Installation Material

NIEDAX - Make: 222 H
Toggle bolt with ceiling hook, galvanized according to DIN 50961, blue passivated, for cavity walls and ceilings, including one washer according to DIN EN ISO 7089 and 1 Hex nut to DIN EN ISO 4035th The load values ​​include a safety factor of 4 The carrying capacity apply only with adequate bearing capacity of the ground.

Haleninnendurchm. 13mm

Threaded Rod: 4 M

Thread length: 70 mm

Total length L: 95 mm

Capacity Q: 0.1 kN

Hole diameter: 12 mm

NIEDAX model no. 222 H

Type: 222H
Item: 25 ST.
Sales unit: 50 pieces
Lieske Part No.: 220605

NIEDAX - Brand: 223 D toggle bolts threaded rod, galvanized to DIN 5 96
, Blue passivated, for cavity walls and ceilings, including 2 washers according to DIN EN ISO 7 89 and 2 hexagonal nuts according to DIN EN ISO 4 35 The load values ​​include a safety factor of 4 The carrying capacity apply only with adequate bearing capacity of the ground. Threaded rod: threaded rod 5 M Length:
F mm Load capacity:
, KN Hole diameter:
5 mm NIEDAX model no. 223 D Type: 223D item: 25 ST.
Sales unit: 50 pieces
Lieske Part No.: 866011

Toggle anchor with ceiling hook, galvanized according to DIN EN ISO 2081, blue passivated, the axle is made of brass, for use on hollow ceilings and walls, including 1 flat washer and 1 hexagon nut according to DIN EN ISO 4035. The load values include a safety factor of 5. The load-bearing capacity information only applies if the substrate has sufficient load-bearing capacity. Threaded rod: M 5 Thread length: 70 mm Total length: 98 mm Borehole diameter: 15 mm Required cavity depth: 70 mm Max. panel thickness: 20 mm Load-bearing capacity F: 0.12 kN
Sales unit: 50 pieces
Lieske Part No.: 544996

Ceiling outlet for web cable, with hook screw and dowel Ø 10 mm, can be used for 2-, 3-, and 4-core web cable, impact-resistant, halogen-free. To prevent plaster damage, the ceiling outlet for web cable must be used on every cable outlet, unless wall outlet boxes are required! Dimensions (approx. dimensions) B : 50 mm Material ceiling outlet/dowel : PS (polystyrene) Material hook screw : galvanized steel wire Material hexagon nut : brass, bare Color : white
Sales unit: 50 pieces
Lieske Part No.: 532821

Anchor/profile rail model 2986, C-profile according to DIN EN 60715, perforated. Matching U-clamps (BU... and BUK...). The SKC 86 protective cap must be installed in areas where there is a personal risk. To ensure that the protective cap can be fitted without any problems, a distance of at least 30 mm must be kept from the end of the profile. Please observe additional regulations for use in functional maintenance! The fastening of the anchor rail to the subsoil and the fastening distances can be found in the relevant valid test certificate. Dimensions (approx. dimensions) H x W x D: 22 x 40 x 2 mm Slot width: 18 mm Profile perforation: 11.5 x 30 mm Center distance: 50 mm Delivery length L: 2000 mm Material: Steel, strip galvanized according to DIN EN 10346
Sales unit: 2 meters
Lieske Part No.: 366375

Pipe and cable spacing clamp, with long fastening hole, for cables and electrical installation pipes in accordance with DIN EN 61386-21, for screwing on with push-through anchor DAM 6X... or screw anchor NSA 6X.../FKK-T30. Dimensions (approx. dimensions) W x L : 18 x 89 mm Long fastening hole : 6.4 x 10 mm for cable Ø : 47 - 55 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 50 Material : Steel, hot-dip galvanized in accordance with DIN EN ISO 1461 Screw material : Stainless steel, material no. 1.4301, 1.4303 Niedax model no. : 856 F
Sales unit: 20 pieces
Lieske Part No.: 466975

Hammer foot clamp, with strip-galvanized steel pressure tray according to DIN EN 10346, hammer foot clamp hot-dip galvanized according to DIN EN ISO 1461, suitable for NIEDAX series/anchor rails (2910-2920) with 11-12 mm slot width, counter trays (GWA/GWS...) and double trays (DW...) must be ordered separately. Allocation one above the other: 2 cables for cable Ø: 14 - 16 mm
Sales unit: 100 pieces
Lieske Part No.: 318813

Hammer foot clamp, with strip-galvanized steel pressure tray according to DIN EN 10346, hammer foot clamp hot-dip galvanized according to DIN EN ISO 1461, suitable for NIEDAX series/anchor rails (2910-2920) with 11-12 mm slot width, counter trays (GWA/GWS...) and double trays (DW...) must be ordered separately. Allocation one above the other: 2 cables for cable Ø: 22 - 26 mm
Sales unit: 100 pieces
Lieske Part No.: 318819

Hammer foot clamp, with strip-galvanized steel pressure tray according to DIN EN 10346, hammer foot clamp hot-dip galvanized according to DIN EN ISO 1461, suitable for NIEDAX series/anchor rails (2910-2920) with 11-12 mm slot width, counter trays (GWA...) and double trays (DW...) must be ordered separately. Allocation one above the other: 2 cables for cable Ø: 42 - 46 mm
Sales unit: 50 pieces
Lieske Part No.: 318823

Hammer foot clamp, with strip-galvanized steel pressure tray according to DIN EN 10346, hammer foot clamp hot-dip galvanized according to DIN EN ISO 1461, suitable for NIEDAX series/anchor rails (2910-2920) with 11-12 mm slot width, counter trays (GWA/GWS...) and double trays (DW...) must be ordered separately. Allocation one above the other: 3 cables for cable Ø: 14 - 16 mm
Sales unit: 100 pieces
Lieske Part No.: 318826

Cable support tray system for wall mounting or for fastening to rails. In accordance with VDE 0298-565-1 and VDE 0298-565-2, a maximum support distance of 0.8 m should not be exceeded. The load-bearing capacity information only applies if the support is sufficiently anchored to the supporting surface and if the surfaces of the vertical profile/anchor rails and the tray support rails in the clamping area are made of steel or galvanized steel. If the clamping area has a coat of paint, this must be removed, otherwise the load-bearing capacity is not given or guaranteed. Danger of slipping! 1. The cable support tray system in tray widths of 40, 50, 60, 70, 80 and 120 mm is available on request. Fastening material must be ordered separately, depending on the application. Dimensions (approx. dimensions) Tray W x L: 100 x 200 mm Number of support trays: 1 Load capacity F at B/2: 0.5 kN Rail H x W: 140 x 72 mm Rail holes: 11 x 16 mm Center hole spacing: 100 mm Number of holes: 2 Material: Steel, hot-dip galvanized according to DIN EN ISO 1461
Lieske Part No.: 1882702

U-clamp, for angle iron, with strip-galvanized steel pressure pan according to DIN EN 10346, bracket hot-dip galvanized according to DIN EN ISO 1461, can also be used on unequal-sided angle steel and U-iron with a max. leg length of 40 mm, counter pans (GWU/GWS...) and double pans (DW...) must be ordered separately. Allocation one above the other: 3 cables for cable Ø: 26 - 28 mm Angle iron dimensions H x W x D: 40 x 40 x 4-6 mm
Sales unit: 100 pieces
Lieske Part No.: 318828

Universal U-clamp, with strip-galvanized steel pressure pan according to DIN EN 10346, bracket hot-dip galvanized according to DIN EN ISO 1461, suitable for NIEDAX anchor rails (2985-2996Z) with 18-22 mm slot width, counter pans (GWU/GWS...) and double pans (DW...) must be ordered separately. For use in functional maintenance, please observe additional regulations! Allocation one above the other: 3 cables for cable Ø: 16 - 18 mm
Sales unit: 100 pieces
Lieske Part No.: 318762

GRIPPLE set cross anchor and express lock, quick suspension system, versatile and ready to use, for attachment to steel, concrete or wooden beams. The load-bearing capacity F only applies to assembly according to regulations. Set consists of: 1 cut-to-length wire rope with cross anchor for drill hole and end sleeve 1 self-locking GRIPPLE for quick attachment with express lock (integrated adjustment system) Dimensions (approx. dimensions) Rope Ø: 2 mm Rope length L: 1 m Drill hole Ø: 8 mm Load-bearing capacity F: 0.45 kN (5-fold safety against breakage) Wire rope material: steel, galvanized
Sales unit: 10 pieces
Lieske Part No.: 467978

U-clamp, for angle iron, with plastic pressure tray made of PP, halogen-free, tray insert strip-galvanized according to DIN EN 10346, bracket hot-dip galvanized according to DIN EN ISO 1461, can also be used on unequal-sided angle steel and U-iron with a maximum leg length of 40 mm, counter trays (GWU...) must be ordered separately. Assignment: 1 cable for cable Ø: 82 - 90 mm Angle iron dimensions H x W x D: 40 x 40 x 4-6 mm
Sales unit: 25 pieces
Lieske Part No.: 318840

U-clamp, for angle iron, with plastic pressure tray made of PP, halogen-free, tray insert strip galvanized according to DIN EN 10346, bracket hot-dip galvanized according to DIN EN ISO 1461, can also be used on unequal-sided angle steel and U-iron with a maximum leg length of 40 mm, counter trays (GWU...) must be ordered separately. Assignment: 1 cable for cable Ø: 90 - 100 mm Angle iron dimensions H x W x D: 40 x 40 x 4-6 mm
Sales unit: 25 pieces
Lieske Part No.: 318841

U-clamp, for angle iron, with plastic pressure tray made of PP, halogen-free, tray insert strip galvanized according to DIN EN 10346, bracket hot-dip galvanized according to DIN EN ISO 1461, can also be used on unequal-sided angle steel and U-iron with a max. leg length of 40 mm, counter trays (GWU/GWS...) and double trays (DW...) must be ordered separately. Allocation one above the other: 2 cables for cable Ø: 18 - 22 mm Angle iron dimensions H x W x D: 40 x 40 x 4-6 mm
Sales unit: 100 pieces
Lieske Part No.: 318842

Bügelschelle, für Winkeleisen, einschließlich Kunststoffdruckwanne mit UV-Schutz und Zapfenschraube M 6 mit Mehrfachantrieb, einsetzbar an gleich- und ungleichschenkligem Winkelstahl sowie U-Eisen. Gegenwannen GWU ... / GWS ... und Doppelwanne DW ... bitte gesondert bestellen. Verwendung für : gleich- und ungleichschenkligem Winkelstahl sowie U-Eisen mit einer Schenkellänge von max. 40 mm sowie einer Dicke von 4 - 6 mm Abmessungen (ca. Maße) Belegung übereinander : 2 Kabel für Kabel-Ø : 26 - 30 mm Werkstoff Bügel : Stahl, tauchfeuerverzinkt nach DIN EN ISO 1461 Werkstoff Druckwanne : Polypropylen (PP), halogenfrei, mit UV-Schutz, Farbton schwarz Werkstoff Wanneneinlage : Stahl, bandverzinkt nach DIN EN 10346 Verkaufseinheit: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 2144067

Bügelschelle, für Winkeleisen, einschließlich Kunststoffdruckwanne mit UV-Schutz und Zapfenschraube M 6 mit Mehrfachantrieb, einsetzbar an gleich- und ungleichschenkligem Winkelstahl sowie U-Eisen. Gegenwannen GWU ... / GWS ... und Doppelwanne DW ... bitte gesondert bestellen. Verwendung für : gleich- und ungleichschenkligem Winkelstahl sowie U-Eisen mit einer Schenkellänge von max. 40 mm sowie einer Dicke von 4 - 6 mm Abmessungen (ca. Maße) Belegung übereinander : 2 Kabel für Kabel-Ø : 30 - 34 mm Werkstoff Bügel : Stahl, tauchfeuerverzinkt nach DIN EN ISO 1461 Werkstoff Druckwanne : Polypropylen (PP), halogenfrei, mit UV-Schutz, Farbton schwarz Werkstoff Wanneneinlage : Stahl, bandverzinkt nach DIN EN 10346 Verkaufseinheit: 1 ST.
Sales unit: 100 pieces
Lieske Part No.: 2144068

U-clamp, for angle iron, with plastic pressure tray made of PP, halogen-free, tray insert strip galvanized according to DIN EN 10346, bracket hot-dip galvanized according to DIN EN ISO 1461, can also be used on unequal-sided angle steel and U-iron with a max. leg length of 40 mm, counter trays (GWU...) and double trays (DW...) must be ordered separately. Allocation one above the other: 2 cables for cable Ø: 46 - 50 mm Angle iron dimensions H x W x D: 40 x 40 x 4-6 mm
Sales unit: 50 pieces
Lieske Part No.: 318844

U-clamp, with toothed clamp base, with plastic pressure tray made of PP, halogen-free, tray insert strip-galvanized according to DIN EN 10346, bracket hot-dip galvanized according to DIN EN ISO 1461, for flat iron with a thickness of 4-12 mm, can also be used on existing steel structures, counter trays (GWU/GWS...) must be ordered separately. Assignment: 1 cable for cable Ø: 22 - 26 mm
Sales unit: 100 pieces
Lieske Part No.: 318845

U-clamp, with toothed clamp base, with plastic pressure tray made of PP, halogen-free, tray insert strip-galvanized according to DIN EN 10346, bracket hot-dip galvanized according to DIN EN ISO 1461, for flat iron with a thickness of 4-12 mm, can also be used on existing steel structures, counter trays (GWU/GWS...) and double trays (DW...) must be ordered separately. Allocation one above the other: 2 cables for cable Ø: 22 - 26 mm
Sales unit: 100 pieces
Lieske Part No.: 318847

U-clamp, with toothed clamp base, with plastic pressure tray made of PP, halogen-free, tray insert strip-galvanized according to DIN EN 10346, bracket hot-dip galvanized according to DIN EN ISO 1461, for flat iron with a thickness of 4-12 mm, can also be used on existing steel structures, counter trays (GWU/GWS...) and double trays (DW...) must be ordered separately. Allocation one above the other: 2 cables for cable Ø: 26 - 30 mm
Sales unit: 100 pieces
Lieske Part No.: 318848

Profile clamp including M 8 stud screw with slotted hexagon head and clamping plate, for clamping to support profiles with parallel flanges or with slanted flanges up to a maximum of 14% inclination and as a supply line to the energy consumers. The fastening materials used can vary depending on the application! Dimensions (approx. dimensions) H x W x L: 57 x 40 x 47 mm Threaded connections: M 8 Load capacity specification vertical nominal load F1: 1.8 kN Load capacity specification vertical nominal load F2: 1.6 kN Flange thickness of the support t: 6 - 35 mm Screw tightening torque: 4 Nm Wrench size: SW 13 Material: Stainless steel, material no. 1.4571
Sales unit: 25 pieces
Lieske Part No.: 468457

Cylinder head screw according to DIN EN ISO 1207, with slot. Dimensions (approx. dimensions) Length L: 20 mm Thread: M 6 Strength class: 4.8 Material: Steel, galvanized according to DIN EN ISO 4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 318854

Gitterrinnen-Befestigungsklemme, horizontal/vertikal, zur Befestigung von Gitterrinnen an horizontalen und vertikalen Stahlträgerflanschen, eine wechselseitige Anordnung der Hakenschrauben gewährleistet eine sichere Befestigung der Gitterrinne an der Gitterrinnen-Befestigungsklemme, eine rechtwinklige Aussparung in den Schenkeln ermöglicht eine Anbringung an runden Stützenprofilen oder eine Montage von Kabelschutzrohren = Ø 30 mm, bei horizontaler Montage kann eine zusätzliche Abhängung mittels Gewindestab M 10/... an der Befestigungsklemmenspitze durch eine Lochung Ø 11 mm erfolgen, stirnseitig kann überdies eine Schraubabstandsschelle SASS 30 E3 befestigt werden, durch Auslässe in der horizontalen Auflagefläche besteht die Möglichkeit zur Montage von bis zu 4 Bügelschellen B 14 - 76 E3 (je nach Größe) in Registerverlegung, einschließlich anteilmäßigen Befestigungszubehör aus Edelstahl, Werkstoff Nr. 1.4301, AISI 304. Verwendung für Gitterrinnen : GR... E3 GRS... E3 MTC...100 - ... E3 MTCG ... Abmessungen (ca. Maße) Gesamtlänge L : 173 mm Auflagelänge L1 : 148 mm Stahlträgerflanschstärke : = 20 mm Tragfähigkeit F1 horizontal bei L 1/2 : 0,35 kN Tragfähigkeit F2 vertikal bei L 1/2 : 0,6 kN Schraubenanzugsmoment : 4 Nm Werkstoff : Edelstahl, Werkstoff Nr. Verkaufseinheit: 1 ST.
Sales unit: 10 pieces
Lieske Part No.: 536492

Hammer head screw, with teeth, including hexagon nut and washer in accordance with DIN EN ISO 7093-1, can be used at any point in the profile. Use for: anchor rail 2996Z with 22 mm slot width, wall bracket STRUT HKC 96Z/..., hanging post and wall bracket STRUT HKC 96ZD/... Dimensions (approx. dimensions) Head length: 34.5 mm Head width: 19.5 mm Head height: 11 mm Thread: M 12 Length L: 30 mm Strength class: 4.6 Material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Sales unit: 50 pieces
Lieske Part No.: 469435

Flat head screw with hexagon socket according to DIN 7380. Dimensions (approx. dimensions) Thread: M 8 Length L: 16 mm Wrench size: SW 5 Material: Steel, hot-dip galvanized according to DIN EN ISO 1461
Sales unit: 50 pieces
Lieske Part No.: 1102149

Sammelhalter, mit einer hohen mechanischen Festigkeit, zur Verlegung von Leitungsbündel an Wand und Decke, zur Schnellbefestigung mit Schlüssellochtechnologie, geeignet zur Montage in korrosiver Umgebung sowie für die Lebensmittelindustrie. Zur Verwendung im Funktionserhalt bzw. für Unterdecken mit brandschutztechnischen Anforderungen (Muster-Leitungsanlagen-Richtlinie MLAR 2/2015) bitte Zusatzvorschriften beachten! Abmessungen (ca. Maße) Höhe H x Breite B (lichte Innenmaße) : 56 x 34 mm max. Belegung : 15 Leitungen NYM 3x1.5 mm² Werkstoff : Edelstahl, Werkstoff Nr. 1.4571, AISI 316Ti Verkaufseinheit: 1 ST.
Lieske Part No.: 878030

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric electrical installation pipe. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 12 x 45 mm Internal connection thread : M 6 for cable Ø : 19 - 21 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 20 Material : steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material : steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no. : SAS 20 V
Sales unit: 50 pieces
Lieske Part No.: 1342455

E-clips, flange claw, for hammering onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 14 - 20 mm Clamping depth C: 33 mm Mounting distance to support flange B: 7.5 mm Side and bottom connection: M 6 Connection hole: Ø 7 mm Load capacity F: 0.45 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 100 pieces
Lieske Part No.: 460701

E-clips, flange claw with angle hanger, for hammering onto a wide range of support flanges, for threaded rod suspensions. Dimensions (approx. dimensions) for flange thickness T: 8 - 14 mm for connecting threaded rod: M 8 Distance to flange surface A: 54 mm Load capacity F: 0.68 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 25 pieces
Lieske Part No.: 460706

E-clips, flange claw 180°, for hammering onto a wide range of support flanges, for threaded rod suspension. Dimensions (approx. dimensions) for flange thickness T: 8 - 14 mm Impact depth B: 20.3 mm Tab distance to flange edge A: 26 mm Connection hole: Ø 6.5 mm Load capacity F: 0.2 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 100 pieces
Lieske Part No.: 460711

E-clips, flange claw 180°, for hammering onto a wide range of support flanges, for threaded rod suspension. Dimensions (approx. dimensions) for flange thickness T: 14 - 20 mm Impact depth B: 20.3 mm Tab distance to flange edge A: 26.6 mm Connection hole: Ø 6.5 mm Load capacity F: 0.2 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 100 pieces
Lieske Part No.: 460712

E-Klips, Schraubklemme mit Winkelabhänger, zum Anschrauben an verschiedenste Trägerflansche, für Gewindestababhängung. Abmessungen (ca. Maße) für Flanschstärke T : 1 - 18 mm Klemmauflage D : 19,5 mm für Anschlussgewindestab : M 10 Tragfähigkeit F : 0,45 kN Werkstoff : Stahl, mechanisch verzinkt/passiviert nach DIN EN ISO 9227 Verkaufseinheit: 25 ST.
Sales unit: 25 pieces
Lieske Part No.: 1276568

E-Klips, Flanschkralle mit Rohrclip, zum Aufschlagen mit dem Hammer auf verschiedenste Trägerflansche, Rohrclip an Flanschkralle drehbar, für Rohrabhängung. Abmessungen (ca. Maße) für Flanschstärke T : 14 - 20 mm Aufschlagtiefe B : 26,6 mm für Rohr-Ø : 26 - 32 mm Tragfähigkeit F : 0,12 kN Werkstoff : Stahl, mechanisch verzinkt/passiviert nach DIN EN ISO 9227 Verkaufseinheit: 25 ST.
Sales unit: 25 pieces
Lieske Part No.: 1276569

E-clips, flange claw with pipe clip, for striking with a hammer on various support flanges, pipe clip on flange claw can be rotated, for pipe suspension. Dimensions (approx. dimensions) for flange thickness T: 14 - 20 mm Impact depth B: 26.6 mm for pipe Ø: 18 - 25 mm Load capacity F: 0.07 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 25 pieces
Lieske Part No.: 460717

E-clips, flange claw with pipe clip, for striking with a hammer on various support flanges, pipe clip on flange claw can be rotated, for pipe suspension. Dimensions (approx. dimensions) for flange thickness T: 14 - 20 mm Impact depth B: 26.6 mm for pipe Ø: 29 - 33 mm Load capacity F: 0.07 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 25 pieces
Lieske Part No.: 460718

E-clips, universal flange claw with pipe clip, for striking with a hammer on a wide variety of support flanges, pipe clip on flange claw can be rotated, for pipe suspension. For flange thickness T: 14 - 20 mm Clamping depth of the flange claw: 33 mm For pipe Ø: 26 - 32 mm Load capacity F: 0.45 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 25 pieces
Lieske Part No.: 460720

E-clips, universal flange claw with pipe clip, for hammering onto a wide range of support flanges, pipe clip can be rotated on the flange claw, for pipe suspension. For flange thickness T: 14 - 20 mm Clamping depth of the flange claw: 33 mm For pipe Ø: 32 - 40 mm Load capacity F: 0.45 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 25 pieces
Lieske Part No.: 460721

Universal U-clamp, made entirely of stainless steel, material no. 1.4301, suitable for NIEDAX anchor rails (2985-2996Z) with 18-22 mm slot width, counter troughs (GWU...) and double troughs (DW...) must be ordered separately. For use in functional maintenance, please observe additional regulations! Allocation one above the other: 2 cables for cable Ø: 16 - 18 mm
Sales unit: 100 pieces
Lieske Part No.: 1051097

Hammer foot clamp, with pressure tray, made entirely of stainless steel, material no. 1.4301, suitable for NIEDAX series/anchor rails (2910-2920) with 11-12 mm slot width, counter trays (GWA...) must be ordered separately. Assignment: 1 cable for cable Ø: 42 - 46 mm
Sales unit: 100 pieces
Lieske Part No.: 466816

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 20 - 25 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 50 pieces
Lieske Part No.: 460738

Universal clamp, made entirely of stainless steel E5, material no. 1.4571, suitable for NIEDAX anchor rails (2985-2996Z) with 18-22 mm slot width, counter trough (GWU...) must be ordered separately. For use in functional maintenance, please observe additional regulations! Assignment: 1 cable for cable Ø: 22 - 30 mm
Sales unit: 100 pieces
Lieske Part No.: 466810

Pipe and cable spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken to ensure that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for screwing onto screw dowels with a thread length of up to 8 mm. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 14 x 49.5 mm Internal connection thread : M 6 for cable Ø : 15 - 19 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 16 Material : steel, hot-dip galvanized in accordance with DIN EN ISO 1461 Screw material : stainless steel, material no. 1.4301, 1.4303 Niedax model no. : 851 GF
Sales unit: 50 pieces
Lieske Part No.: 466965

Pipe and cable spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken to ensure that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for screwing onto screw dowels with a thread length of up to 8 mm. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 14 x 53 mm Internal connection thread : M 6 for cable Ø : 19 - 24 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 20 Material : steel, hot-dip galvanized in accordance with DIN EN ISO 1461 Screw material : stainless steel, material no. 1.4301, 1.4303 Niedax model no. : 852 GF
Sales unit: 50 pieces
Lieske Part No.: 466970

Pipe and cable spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken to ensure that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for screwing onto screw dowels with a thread length of up to 8 mm. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 18 x 89 mm Internal connection thread : M 6 for cable Ø : 47 - 55 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 50 Material : steel, hot-dip galvanized in accordance with DIN EN ISO 1461 Screw material : stainless steel, material no. 1.4301, 1.4303 Niedax model no. : 856 GF
Sales unit: 20 pieces
Lieske Part No.: 466977

Pipe and cable spacing clamp, with long fastening hole, for cables and electrical installation pipes in accordance with DIN EN 61386-21, for screwing on with push-through anchor DAM 6X... or screw anchor NSA 6X.../FKK-T30. Dimensions (approx. dimensions) W x L : 14 x 49.5 mm Long fastening hole : 6.4 x 10 mm for cable Ø : 15 - 19 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 16 Material : Steel, strip galvanized in accordance with DIN EN 10346 Screw material : Steel, electrogalvanized in accordance with DIN EN ISO 4042 Niedax model no. : 851
Sales unit: 50 pieces
Lieske Part No.: 532822

NIEDAX - Make: AL 851
Pipe and cable clamp spacing, aluminum, screws in stainless steel, with slotted fixing holes for Pg and metric pipes according to DIN EN 60423rd

Long hole: 5.6 x 8 mm for cable diameter: 15 - 19 mm for conduit threads: Pg 11 Pg 9 + for metric Rohrgr: M 16th NIEDAX Model No: AL 851. Type: 851AL










Quantity: 1 unit.
Sales unit: 50 pieces
Lieske Part No.: 131053

NIEDAX - Make 851 G
Pipe and cable clamp distance from galvanized steel strip galvanized to DIN EN 10346, screws to DIN ISO 4042, with internal thread connection M 6, for Pg and metric pipes according to DIN EN 60423rd

for cable diameter: 15 - 19 mm for conduit threads: Pg 9 + 11 for metric Rohrgr: M 16th . NIEDAX Model No: G 851 Type: 851g








Item: 100 ST.
Sales unit: 50 pieces
Lieske Part No.: 260839