Installation Material

GRIPPLE trapezoidal hook and express fastener, quick suspension system, versatile and ready to use, for fastening to trapezoidal sheet ceilings. The load-bearing capacity F only applies if the ceiling is sufficiently anchored to the supporting surface and installed correctly. Make sure that the selected end is suitable for the respective support structure and follow the manufacturer's recommendations for all installations. Set consists of: 1 cut-to-length wire rope with trapezoidal sheet hook 1 self-locking GRIPPLE for quick fastening with express fastener (integrated adjustment system) Dimensions (approx. dimensions) Rope Ø: 2 mm Rope length L: 2 m Hook Ø: 5 mm Load-bearing capacity F: 0.45 kN (5-fold safety against breakage was calculated on a 2 mm trapezoidal sheet) Wire rope material: steel, galvanized
Sales unit: 10 pieces
Lieske Part No.: 1332691

GRIPPLE trapezoidal hook and express fastener, quick suspension system, versatile and ready to use, for fastening to trapezoidal sheet ceilings. The load-bearing capacity F only applies if the ceiling is sufficiently anchored to the supporting surface and installed correctly. Make sure that the selected end is suitable for the respective support structure and follow the manufacturer's recommendations for all installations. Set consists of: 1 cut-to-length wire rope with trapezoidal sheet hook 1 self-locking GRIPPLE for quick fastening with express fastener (integrated adjustment system) Dimensions (approx. dimensions) Rope Ø: 2 mm Rope length L: 3 m Hook Ø: 5 mm Load-bearing capacity F: 0.45 kN (5-fold safety against breakage was calculated on a 2 mm trapezoidal sheet) Wire rope material: steel, galvanized
Sales unit: 10 pieces
Lieske Part No.: 1332690

GRIPPLE trapezoidal hook and express fastener, quick suspension system, versatile and ready to use, for fastening to trapezoidal sheet ceilings. The load-bearing capacity F only applies if the ceiling is sufficiently anchored to the supporting surface and installed correctly. Make sure that the selected end is suitable for the respective support structure and follow the manufacturer's recommendations for all installations. Set consists of: 1 cut-to-length wire rope with trapezoidal sheet hook 1 self-locking GRIPPLE for quick fastening with express fastener (integrated adjustment system) Dimensions (approx. dimensions) Rope Ø: 2 mm Rope length L: 5 m Hook Ø: 5 mm Load-bearing capacity F: 0.45 kN (5-fold safety against breakage was calculated on a 2 mm trapezoidal sheet) Wire rope material: steel, galvanized
Sales unit: 10 pieces
Lieske Part No.: 369808

GRIPPLE angle protector No.2-3, to reinforce the support point and to effectively distribute the weight load, prevents rope friction, for GRIPPLE rope systems, halogen-free. Dimensions (approx. dimensions) Leg length: 50 mm for rope Ø: 1.5 - 3 mm Material: Polypropylene (PP)
Sales unit: 10 pieces
Lieske Part No.: 1316178

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width Dimensions (approx. dimensions) Length L: 50 mm Width B: 21 mm Sliding nut height H: 17 mm Thread: M 10 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: grey polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 697283

Sliding nut with fixing aid, for C anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2996Z with 22 mm slot width wall bracket STRUT HKC 96Z/... hanging post and wall bracket STRUT HKC 96ZD/... Dimensions (approx. dimensions) Length L: 50 mm Width B: 25 mm Sliding nut height H: 18 mm Thread: M 10 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: gray polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 239560

Sliding nut with fixing aid, for C-anchor rails, for anchor rails with 18 mm slot width can only be used from the profile end with a fastening screw, not suitable in combination with the anchor rail 2986-1.75... for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on. Use for: anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width Dimensions (approx. dimensions) Length L: 50 mm Width B: 21 mm Sliding nut height H: 17 mm Thread: M 12 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: grey polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 1332945

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2996Z with 22 mm slot width wall bracket STRUT HKC 96Z/... hanging post and wall bracket STRUT HKC 96ZD/... Dimensions (approx. dimensions) Length L: 50 mm Width B: 25 mm Sliding nut height H: 18 mm Thread: M 12 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: gray polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 740765

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width Dimensions (approx. dimensions) Length L: 50 mm Width B: 21 mm Sliding nut height H: 17 mm Thread: M 6 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: grey polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 1332811

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2996Z with 22 mm slot width wall bracket STRUT HKC 96Z/... hanging post and wall bracket STRUT HKC 96ZD/... Dimensions (approx. dimensions) Length L: 50 mm Width B: 25 mm Sliding nut height H: 18 mm Thread: M 6 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: gray polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 1332944

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width Dimensions (approx. dimensions) Length L: 50 mm Width B: 21 mm Sliding nut height H: 17 mm Thread: M 8 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: grey polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 168388

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2996Z with 22 mm slot width wall bracket STRUT HKC 96Z/... hanging post and wall bracket STRUT HKC 96ZD/... Dimensions (approx. dimensions) Length L: 50 mm Width B: 25 mm Sliding nut height H: 18 mm Thread: M 8 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: gray polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 193567

Sliding nut, without screw, can be used at any point with a fastening screw in the profile. Please observe additional regulations for use in functional maintenance! Use for: Anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width 2996Z with 22 mm slot width Wall bracket STRUT HKC 96Z/... Hanging post and wall bracket HKC 96ZD/... Dimensions (approx. dimensions) Length L: 34 mm Width B: 15.5 mm Height H: 10 mm Thread: M 10 Strength class: 8 Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684
Sales unit: 100 pieces
Lieske Part No.: 746614

NIEDAX - Make: GMZ M
2 F sliding nut, steel, channel bars for C-Model 2985, 2986, 2988 and 299 with slot width
8 mm (usable only by the end of the profile) and for C-anchor rails model 2987, 299
, 2992, 2994, 2995, 2996 and 2996Z with 22/26 mm slot width, GMZ M
2 F can be used at any point in the profile with fixing screw, hot-dip galvanized to DIN EN ISO
684th Dimensions L x W: 34 x
8 mm height of the sliding nut:
mm with thread M
2 Property class: 8 NIEDAX model no. GMZ M
2 F Type: GMZM
2F
ST.
Sales unit: 100 pieces
Lieske Part No.: 749335

Gitterrinnen-Befestigungsklemme, horizontal/vertikal, zur Befestigung von Gitterrinnen an horizontalen und vertikalen Stahlträgerflanschen, eine wechselseitige Anordnung der Hakenschrauben gewährleistet eine sichere Befestigung der Gitterrinne an der Gitterrinnen-Befestigungsklemme, eine rechtwinklige Aussparung in den Schenkeln ermöglicht eine Anbringung an runden Stützenprofilen oder eine Montage von Kabelschutzrohren = Ø 30 mm, bei horizontaler Montage kann eine zusätzliche Abhängung mittels Gewindestab M 10/... an der Befestigungsklemmenspitze durch eine Lochung Ø 11 mm erfolgen, stirnseitig kann überdies eine Schraubabstandsschelle SASS 30 befestigt werden, durch Auslässe in der horizontalen Auflagefläche besteht die Möglichkeit zur Montage von bis zu 4 Bügelschellen B(K) 12 - 90 (je nach Größe) in Registerverlegung, einschließlich anteilmäßigen Befestigungszubehör aus Edelstahl, Werkstoff Nr. 1.4301, AISI 304. Verwendung für Gitterrinnen : GR... GRS... GRL... GRCI... MTC...100 - ... MTCG ... Abmessungen (ca. Maße) Gesamtlänge L : 173 mm Auflagelänge L1 : 148 mm Stahlträgerflanschstärke : = 20 mm Tragfähigkeit F1 horizontal bei L 1/2 : 0,6 kN Tragfähigkeit F2 vertikal bei L 1/2 : 0,9 kN Schraubenanzugsmoment : 4 Nm Werkstoff : Stahl, tauchfeuerverzinkt nach DIN EN ISO 1461
Sales unit: 10 pieces
Lieske Part No.: 832935

Gitterrinnen-Befestigungsklemme, horizontal/vertikal, zur Befestigung von Gitterrinnen an horizontalen und vertikalen Stahlträgerflanschen, eine wechselseitige Anordnung der Hakenschrauben gewährleistet eine sichere Befestigung der Gitterrinne an der Gitterrinnen-Befestigungsklemme, eine rechtwinklige Aussparung in den Schenkeln ermöglicht eine Anbringung an runden Stützenprofilen oder eine Montage von Kabelschutzrohren = Ø 30 mm, bei horizontaler Montage kann eine zusätzliche Abhängung mittels Gewindestab M 10/... an der Befestigungsklemmenspitze durch eine Lochung Ø 11 mm erfolgen, stirnseitig kann überdies eine Schraubabstandsschelle SASS 30 befestigt werden, durch Auslässe in der horizontalen Auflagefläche besteht die Möglichkeit zur Montage von bis zu 4 Bügelschellen B(K) 12 - 90 (je nach Größe) in Registerverlegung, einschließlich anteilmäßigen Befestigungszubehör. Verwendung für Gitterrinnen : GR... GRS... GRL... GRCI... MTC...100 - ... MTCG ... Abmessungen (ca. Maße) Gesamtlänge L : 173 mm Auflagelänge L1 : 148 mm Stahlträgerflanschstärke : = 20 mm Tragfähigkeit F1 horizontal bei L 1/2 : 0,6 kN Tragfähigkeit F2 vertikal bei L 1/2 : 0,9 kN Schraubenanzugsmoment : 4 Nm Werkstoff : Stahl, bandverzinkt nach DIN EN 10346
Sales unit: 10 pieces
Lieske Part No.: 696019

Hook screw with M 6 thread, including toothed special flange nut similar to DIN EN 1661, for fastening the mesh cable trays to brackets, to mesh cable tray hanging posts, and to joint connectors. Please note additional regulations for use in functional maintenance! Can be used for: mesh cable trays up to max. 6 mm wire thickness Dimensions (approx. dimensions) Thread: M 6 Thread length: 15 mm Flange nut: Ø 17 mm Material: steel, galvanized in accordance with DIN EN ISO 4042, blue passivated.
Lieske Part No.: 187895

NIEDAX - Make: GSF 0404
Schräggleitmutter with spring (phosphated), for fixing of cable trays on C-anchor rails model 2970 and 2971 according to DIN EN 60715 with slot width 16 mm, GSF ... used at any point in the profile, galvanized according to DIN 50961, passivated.

Dimensions L x W: 26 x 15.5 mm

Height of the sliding nut: 4mm

with thread M 4

Total height: 14 mm

NIEDAX model no. GSF 0404 Type: GSF0404


Quantity: 1 unit.
Sales unit: 25 pieces
Lieske Part No.: 459412

NIEDAX - Make: GSF 0405
Schräggleitmutter with spring (phosphated), for fixing of cable trays on C-anchor rails model 2970 and 2971 according to DIN EN 60715 with slot width 16 mm, GSF ... used at any point in the profile, galvanized according to DIN 50961, passivated.

Dimensions L x W: 26 x 15.5 mm

Height of the sliding nut: 4mm

with thread M 5

Total height: 14 mm

NIEDAX model no. GSF 0405

Type: GSF0405
Item: 100 ST.
Sales unit: 25 pieces
Lieske Part No.: 247075

NIEDAX - Make: GSF 4 6 Schräggleitmutter with spring (phosphated), for fixing of cable trays on C-anchor rails model 297 and 297
according to DIN EN 6 7
5 with slot width
6 mm, as well as for attaching skimmers WBL ... the wide span cable ladders on rail extrusion according to DIN EN 297 6 7
5 with slot width
6 mm, GSF ... used at any point in the profile, galvanized to DIN 5 96
, passivated. Dimensions L x W: 26 x
5.5 mm height of the sliding nut 4 mm with thread M 6 Total height:
4 mm NIEDAX model no. GSF 4 6 Type: GSF 4 6 item:
ST.
Lieske Part No.: 811572

NIEDAX - Make: GSF 0408
Schräggleitmutter with spring (phosphated), for fixing of cable trays on C-anchor rails model 2970 and 2971 according to DIN EN 60715 with slot width 16 mm, GSF ... . applicable at any point in the profile, galvanized according to DIN 50961, passivated Dimensions L x W: 26 x 15.5 mm height of the sliding nut 4 mm with thread M 8 Overall Height: 14 mm NIEDAX model no. GSF 0408 Type : GSF0408












Quantity: 1 unit.
Sales unit: 25 pieces
Lieske Part No.: 556373

Inclined sliding nut, for fastening to C-anchor rail model 2920 with slot width 11 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, blue passivated. Dimensions (approx. dimensions) L x W: 20 x 10.5 mm with thread: M 5 Height of the sliding nut: 4 mm
Sales unit: 100 pieces
Lieske Part No.: 744268

Inclined sliding nut, for fastening to C-anchor rail model 2920 with slot width 11 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, blue passivated. Dimensions (approx. dimensions) L x W: 20 x 10.5 mm Height of the sliding nut: 4 mm with thread: M 6
Sales unit: 100 pieces
Lieske Part No.: 318849

Inclined sliding nut, for fastening to C-anchor rails model 2970, 2971 and 2972 with slot width 16 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 26 x 15.5 mm Height of the sliding nut: 3 mm with thread: M 4
Sales unit: 50 pieces
Lieske Part No.: 104800

Inclined sliding nut, for fastening to C-anchor rails model 2970, 2971 and 2972 with slot width 16 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 26 x 15.5 mm Height of the sliding nut: 3 mm with thread: M 5
Sales unit: 50 pieces
Lieske Part No.: 469975

Inclined sliding nut, for fastening to C-anchor rails model 2970, 2971 and 2972 with slot width 16 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 26 x 15.5 mm Height of the sliding nut: 4 mm with thread: M 6
Sales unit: 50 pieces
Lieske Part No.: 724312

Inclined sliding nut, for fastening to C-anchor rails model 2970, 2971 and 2972 with slot width 16 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 26 x 15.5 mm Height of the sliding nut: 4 mm with thread: M 8
Sales unit: 50 pieces
Lieske Part No.: 366769

Inclined sliding nut, without cylinder head screw, for fastening in C-series rail with 11 mm slot width, GSM... can be used at any point in the profile. for series rail: 2910 Dimensions (approx. dimensions) W x tx L: 9.4 x 1.75 x 18 mm Thread: M 4 Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 148059

Inclined sliding nut, for fastening to C-series rail model 2910 with slot width 11 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, blue passivated. Dimensions (approx. dimensions) L (inclined) x W: 16 x 10 mm with thread: M 4 Height of the sliding nut: 3 mm
Sales unit: 100 pieces
Lieske Part No.: 496017

Inclined sliding nut, for fastening to C-series rail model 2910 with slot width 11 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, blue passivated. Dimensions (approx. dimensions) L (inclined) x W: 16 x 10 mm with thread: M 5 Height of the sliding nut: 3 mm
Sales unit: 100 pieces
Lieske Part No.: 307083

Inclined sliding nut, for fastening to C-series rail model 2913 and C-anchor rail 2914 with slot width 11 mm and C-anchor rails model 2916 and 2917 with slot width 12 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, blue passivated. Dimensions (approx. dimensions) L (inclined) x W: 20 x 13 mm with thread: M 4 Height of the sliding nut: 2.5 mm
Sales unit: 500 pieces
Lieske Part No.: 385792

Inclined sliding nut, for fastening to C-series rail model 2913 and C-anchor rail model 2914 with slot width 11 mm and C-anchor rails model 2916 and model 2917 with slot width 12 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, blue passivated. Dimensions (approx. dimensions) L (inclined) x W: 20 x 13 mm with thread: M 5 Height of the sliding nut: 4 mm
Sales unit: 100 pieces
Lieske Part No.: 801450

NIEDAX - Make: GSM 306
Schräggleitmutter, for mounting on DIN rail series Model 2913 and Model 2914 C-anchor rail with slot width 11 mm and C-anchor rails model 2916 and model 2917 with a slot width of 12 mm, GSM ... . applicable at any point in the profile, galvanized according to DIN 50961, blue passivated Dimension L (tilted) xB: 20 x 13 mm with thread: M6 slide nut height: 4 mm NIEDAX model no. 306 GSM Type: GSM306










Item: 100 ST.
Sales unit: 50 pieces
Lieske Part No.: 156595

Inclined sliding nut, for fastening to C-series rail model 2913 and C-anchor rail model 2914 with slot width 11 mm and C-anchor rails model 2916 and model 2917 with slot width 12 mm, GSM... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, blue passivated. Dimensions (approx. dimensions) L (inclined) x W: 20 x 13 mm with thread: M 8 Height of the sliding nut: 4 mm
Sales unit: 50 pieces
Lieske Part No.: 572303

Inclined sliding nut, without cylinder head screw, for C-anchor rails, can be used at any point with a fastening screw in the profile. For anchor rails/profile rails: 2970, 2971, 2972, 2975 and 2980 with 16 mm slot width Dimensions (approx. dimensions) Length L: 31 mm Width B: 15.5 mm Height H: 4 mm Thread: M 6 Material: Steel, galvanized according to DIN EN ISO 2081/4042, thick-layer passivated
Sales unit: 50 pieces
Lieske Part No.: 176305

NIEDAX - Make: GSM 406 E3
Schräggleitmutter, for C-rail anchor E3 2970 model with a slot width of 16 mm, GSM ... E3 at each point in the profile can be used with screw in stainless steel, material no. 1.4301.

Dimensions L x W: 31 x 15.5 mm

Height of the sliding nut: 4mm

with thread M 6

NIEDAX model no. GSM 406 E3

Type: GSM406E3
Quantity: 1 unit.
Sales unit: 50 pieces
Lieske Part No.: 308894

Inclined sliding nut, without cylinder head screw, for C-anchor rails in E5, can be used at any point with a fastening screw in the profile. for anchor rails/profile rails in E5: 2970, 2971, 2972, 2975 and 2980 with 16 mm slot width Dimensions (approx. dimensions) Length L: 31 mm Width B: 15.5 mm Height H: 4 mm Thread: M 6 Material: Stainless steel, material no. 1.4571
Sales unit: 50 pieces
Lieske Part No.: 1313651

NIEDAX - Make: GSM 408
Schräggleitmutter, for C-anchor rails model 2970, 2971, 2972, 2975 and 2980 with a slot width of 16 mm, GSM ... used at any point in the profile with fixing screw, galvanized according to DIN 50961, passivated.

Dimensions L x W: 31 x 15.5 mm

Height of the sliding nut: 6mm

with thread M 8

NIEDAX model no. 408 GSM

Type: GSM408
Item: 100 ST.
Sales unit: 50 pieces
Lieske Part No.: 171381

Inclined sliding nut, without cylinder head screw, for C-anchor rails in E3, can be used at any point with a fastening screw in the profile. for anchor rails/profile rails in E3: 2970, 2971, 2972, 2975 and 2980 with 16 mm slot width Dimensions (approx. dimensions) Length L: 31 mm Width B: 15.5 mm Height H: 4 mm Thread: M 8 Material: Stainless steel, material no. 1.4301/1.4303
Sales unit: 50 pieces
Lieske Part No.: 410527

NIEDAX - Make: GSM 410
Schräggleitmutter, for C-anchor rails model 2970, 2971, 2972, 2975 and 2980 with a slot width of 16 mm, GSM ... used at any point in the profile with fixing screw, galvanized according to DIN 50961, blue passivated.

Dimensions L x W: 31 x 15.5 mm

Height of the sliding nut: 6mm

with thread M 10 NIEDAX model no. 410 GSM Type: GSM410




Item: 100 ST.
Sales unit: 50 pieces
Lieske Part No.: 348135

NIEDAX - Make: GSM 4
E3 Schräggleitmutter, for C-rail anchor 297 E3 model with slot width
6 mm, GSM ... E3 at each point in the profile can be used with screw in stainless steel, material no.
.43
. Dimensions L x W: 3
x
5.5 mm height of the sliding nut 4 mm with thread M
NIEDAX model no. 4 GSM
E3 Type: GSM4
E3 item:
ST.
Sales unit: 50 pieces
Lieske Part No.: 908317

U-sliding nut, for C-anchor channels model 2970 and 2971, U-sliding nut can only be used from the end of the profile, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 24.5 x 19 mm Height of the sliding nut: 10 mm with thread: M 6
Sales unit: 50 pieces
Lieske Part No.: 180082

U-sliding nut, for C-series rail model 2910, U-sliding nut can only be used from the profile end, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 17 x 13 mm Height of the sliding nut: 4.5 mm with thread: M 4
Sales unit: 100 pieces
Lieske Part No.: 675516

U-sliding nut, for C-series rail model 2913 and C-anchor rail model 2914, U-sliding nut can only be used from the end of the profile, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 21.5 x 13 mm Height of the sliding nut: 6.5 mm with thread: M 5
Sales unit: 100 pieces
Lieske Part No.: 926913

U-sliding nut, for C-anchor channels model 2975 and 2980, U-sliding nut can only be used from the end of the profile, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 28.9 x 20 mm Height of the sliding nut: 10 mm with thread: M 6
Sales unit: 50 pieces
Lieske Part No.: 1426323

U-sliding nut, special design, for fastening to C-anchor rails model 2975 and 2980 with slot width 16 mm, GUE... can be used at any point in the profile, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 26.5 x 19 mm Height of the sliding nut: 10 mm with thread: M 6
Sales unit: 50 pieces
Lieske Part No.: 1426300

NIEDAX - Make: GUF 204
. slide nut, with plastic spring clamp for C-series rail model 2910, slide nut is only from profile end use, self-adhesive, captive, galvanized according to DIN 50961, passivated Dimensions L x W: 16 x 14 mm with thread M 4 NIEDAX model no. GUF 204 Type: GUF204








Quantity: 1 unit.
Lieske Part No.: 655570

Sliding nut, with plastic clamping spring, for C-series rail model 2910, sliding nut can only be used from the end of the profile, self-adhesive, captive, galvanized according to DIN EN ISO 2081, thick-layer passivated. Dimensions (approx. dimensions) L x W: 16 x 14 mm with thread: M 5
Lieske Part No.: 744269

Counter trough, for hammer foot clamp, self-adhesive on C-profile rails using a clamping spring, halogen-free. for clamp: B ... BK ... for C-profile rails with slot width: 16 - 17 mm Dimensions (approx. dimensions) for cable Ø: 90 - 100 mm Length L: 45 mm Operating temperature range: -40° to 80°C Color: light gray RAL: 7035 (similar) Material: Polyethylene (PE) silicone-free (free of paint-wetted substances)
Sales unit: 25 pieces
Lieske Part No.: 193743

Counter trough, for hammer foot clamp, self-adhesive on C-profile rails using a clamping spring, halogen-free. for clamp: B ... BK ... for C-profile rails with slot width: 16 - 17 mm Dimensions (approx. dimensions) for cable Ø: 100 - 110 mm Length L: 45 mm Operating temperature range: -40° to 80°C Color: light gray RAL: 7035 (similar) Material: Polyethylene (PE) silicone-free (free of paint-wetted substances)
Lieske Part No.: 402923