Installation Material

Pipe clamp, double-lobed, with mounting holes, for fastening machine installation pipes. Can be used for: Machine installation pipe MI 60... Machine installation pipe MIG 60... Installation pipe connection MIA 60... Dimensions (approx. dimensions) Height H x Width W x Length L: 61 x 30 x 160 mm Mounting holes: 9.5 x 20 mm Center distance: 120 mm for pipe Ø: 60 mm Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Sales unit: 20 pieces
Lieske Part No.: 723807

Heavy-duty steel dowel, with fixed threaded rod, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The steel dowel has not been tested by the building authorities and can therefore only be used for minor fastenings! Dimensions (approx. dimensions) for thread: M 8 Nominal drilling diameter: 14 mm Dowel length L: 60 mm Total length L: 100 mm Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 1315752

Nail anchor. Anchor for use in concrete for multiple fastening. The nail anchor is placed in a drill hole and spread by applying the load. The nail anchor is suitable for push-through installation. To be installed by lightly hammering the nail head. Permissible loads for centric tension, transverse load and diagonal tension at any angle as well as anchor characteristics and component dimensions for concrete strength classes = B 25 or C 20/25 and = B 55 or C 50/60. The entire approval notice no. ETA-18/0541 must be observed when dimensioning! For outdoor areas we recommend nail anchors made of stainless steel! For use in functional maintenance or for suspended ceilings with fire protection requirements (model pipe system guideline MLAR 2/2015) please observe additional regulations! Area of application The anchor can be used as a multiple fastening for anchoring light ceiling coverings and suspended ceilings in accordance with DIN 18168, as well as for statically comparable anchoring up to 1 kN/m² - also in the tension zone generated by load stresses. Technical details Total length L: 65 mm Nominal bore diameter: 6 mm Clamping range t fix: = 30 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081/4042, blue passivated Approval no.: ETA-18/0541 DoP NI001
Sales unit: 100 pieces
Lieske Part No.: 265452

NIEDAX - Make: NA 6X5 nail anchor made ​​of steel, galvanized to DIN 5 96
, passivated. For use in the functional integrity please follow additional rules!Permissible loads for train-centric, cross and shear loading at any angle and anchor characteristics and dimensions for concrete strength> = 25 B and C, 2/25 When assessing the entire certification No. is: ETA 6 /
75 to note! For outdoor use, we recommend anchor made of stainless steel!Dimensions: Permissible load of single anchors:
, 6 kN Permissible bending moment M: 4 Nm max. Torque when attaching the fixture with torques = t M (D) - Nm nominal drill hole diameter d () = 6 mm cutting diameter <= 6,4 mm hole in the subsequent component d (f) <= 7 mm minimum hole depth h ( )> = 4 mm minimum anchoring depth h (v)> = 3 mm spacing between outer anchors of adjoining groups or between single anchors az> = 2 mm spacing of the outer anchors the component edge ar> =:
mm minimum thickness d (a) = 8 mm total length l = 4 mm fixture thickness t fix <= 5 mm Certificate No.:. ETA 6 /
75 Scope: The anchor may as multiple fixing for the anchorage for suspended ceilings and suspended ceilings according to DIN
8
68, as well as for static anchors similar to
kN / mý - used - even in the tension zone generated from load voltages. For outdoor use, we recommend anchor made &#8203;&#8203;of stainless steel. NIEDAX model no. 6x5 NA Type: NA6x5 item:
ST.
Sales unit: 100 pieces
Lieske Part No.: 537737

Holzschraube, mit Tellerkopf und Torxantrieb. Zur Befestigung von Niedax Kabeltragsystemen mit integriertem Funktionserhalt an tragenden Holzbauteilen nach DIN EN 1995-1-2. Europäische techn. Bewertung: Zulassungs.Nr. ETA-19/0553. Zur Verwendung im Funktionserhalt bitte Zusatzvorschriften beachten! Gew.-Aussen-Ø : 10 mm Länge : 100 mm Gewindelänge : 93 mm Torxantrieb : T40 Kopf-Ø : 22,5 mm Empf. Anzugsmoment : 9,5 Nm Bohrungs-Ø Nadelholz : 6,0 mm Bohrungs-Ø Buche, Eiche, Esche : 7,0 mm Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert
Sales unit: 50 pieces
Lieske Part No.: 705776

Holzschraube, mit Tellerkopf und Torxantrieb. Zur Befestigung von Niedax Kabeltragsystemen mit integriertem Funktionserhalt an tragenden Holzbauteilen nach DIN EN 1995-1-2. Europäische techn. Bewertung: Zulassungs.Nr. ETA-19/0553. Zur Verwendung im Funktionserhalt bitte Zusatzvorschriften beachten! Gew.-Aussen-Ø : 10 mm Länge : 140 mm Gewindelänge : 84 mm Torxantrieb : T40 Kopf-Ø : 22,5 mm Empf. Anzugsmoment : 9,5 Nm Bohrungs-Ø Nadelholz : 6,0 mm Bohrungs-Ø Buche, Eiche, Esche : 7,0 mm Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert
Sales unit: 50 pieces
Lieske Part No.: 705777

Holzschraube, mit Tellerkopf und Torxantrieb. Zur Befestigung von Niedax Kabeltragsystemen mit integriertem Funktionserhalt an tragenden Holzbauteilen nach DIN EN 1995-1-2. Europäische techn. Bewertung: Zulassungs.Nr. ETA-19/0553. Zur Verwendung im Funktionserhalt bitte Zusatzvorschriften beachten! Gew.-Aussen-Ø : 6 mm Länge : 60 mm Gewindelänge : 56 mm Torxantrieb : T30 Kopf-Ø : 14 mm Empf. Anzugsmoment : 9,5 Nm Bohrungs-Ø Nadelholz : 4,0 mm Bohrungs-Ø Buche, Eiche, Esche : 4,0 mm Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert
Sales unit: 100 pieces
Lieske Part No.: 705772

Schraubanker mit Flachrundkopf und Torxantrieb T30. Zur Verwendung im Funktionserhalt bzw. für Unterdecken mit brandschutztechnischen Anforderungen (Muster-Leitungsanlagen-Richtlinie MLAR 2/2015) bitte Zusatzvorschriften beachten! Anwendung : Anzahl und Anordnung der Schraubanker sind der Ausführungsplanung bzw. dem statischen Nachweis zu entnehmen und einzuhalten. Einbau und Montage gemäß Europäisch Technischer Bewertung ETA-15/0784 bzw. Montageanleitung im gerissenen und ungerissenen Beton C20/25 bis C50/60. Bei der Bemessung ist der gesamte Zulassungsbescheid ETA-15/0784 zu beachten. Zur Verwendung in Mauerwerk gemäß Europäisch Technischer Bewertung ETA-20/0132. Für Kalksandstein KS, Kalksandlochstein KSL und Vollziegel MZ liegt ein Brandschutzgutachten für den Funktionserhalt vor. Verwendung in trockenen Innenräumen. Setzen des Schraubankers mit Tangential Schlagschrauber oder von Hand. Verwendung für : Sammelhalter SHS... Technische Angaben Ø : 6 mm Länge L : 35 mm Kopf-Ø : 11 mm Bohrnenn-Ø : 5 mm Klemmbereich t fix : 1 mm empfohlenes Drehmoment : 10 Nm Torxantrieb : T30 Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert Zulassungs-Nr. : ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 691746

Screw anchor with flat round head and Torx drive T30. For use in functional maintenance or for suspended ceilings with fire protection requirements (model pipe system guideline MLAR 2/2015), please observe additional regulations! Application: The number and arrangement of the screw anchors can be found in the implementation plan or the static proof and must be observed. Installation and assembly in accordance with European Technical Assessment ETA-15/0784 or assembly instructions in cracked and non-cracked concrete C20/25 to C50/60. The entire approval notice ETA-15/0784 must be observed when dimensioning. For use in masonry, see general type approval Z-21.1-2103. A fire protection report for functional maintenance is available for KS sand-lime brick, KSL perforated sand-lime brick and MZ solid brick. Use in dry interior rooms. Set the screw anchor with a tangential impact wrench or by hand. Use for: Collective holder SHS... Technical details Ø: 6 mm Length L: 50 mm Head Ø: 11 mm Nominal bore Ø: 5 mm Clamping range t fix: 5 mm Recommended torque: 10 Nm Torx drive: T30 Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated Approval no.: ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 1348981

Schraubanker mit Sechskantkopf und metrischem Anschlußgewinde M 6. Zur Verwendung im Funktionserhalt bzw. für Unterdecken mit brandschutztechnischen Anforderungen (Muster-Leitungsanlagen-Richtlinie MLAR 2/2015) bitte Zusatzvorschriften beachten! Anwendung : Anzahl und Anordnung der Schraubanker sind der Ausführungsplanung bzw. dem statischen Nachweis zu entnehmen und einzuhalten. Einbau und Montage gemäß Europäisch Technischer Bewertung ETA-15/0784 bzw. Montageanleitung im gerissenen und ungerissenen Beton C20/25 bis C50/60. Bei der Bemessung ist der gesamte Zulassungsbescheid ETA-15/0784 zu beachten. Zur Verwendung in Mauerwerk gemäß Europäisch Technischer Bewertung ETA-20/0132. Für Kalksandstein KS, Kalksandlochstein KSL und Vollziegel MZ liegt ein Brandschutzgutachten für den Funktionserhalt vor. Verwendung in trockenen Innenräumen. Setzen des Schraubankers mit Tangential Schlagschrauber oder von Hand. Verwendung für : Schraubabstandschellen SAS... Rohr- und Kabelabstandschellen 85... G Technische Angaben Ø : 6 mm Gesamtlänge L : 55 mm Bohrnenn-Ø : 5 mm Anschlußgewinde : M 6 empfohlenes Drehmoment : 10 Nm Schlüsselweite : SW 10 Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert Zulassungs-Nr. : ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 691747

Schraubanker mit großem Flachrundkopf und Torxantrieb T30. Zur Verwendung im Funktionserhalt bzw. für Unterdecken mit brandschutztechnischen Anforderungen (Muster-Leitungsanlagen-Richtlinie MLAR 2/2015) bitte Zusatzvorschriften beachten! Anwendung : Anzahl und Anordnung der Schraubanker sind der Ausführungsplanung bzw. dem statischen Nachweis zu entnehmen und einzuhalten. Einbau und Montage gemäß Europäisch Technischer Bewertung ETA-15/0784 bzw. Montageanleitung im gerissenen und ungerissenen Beton C20/25 bis C50/60. Bei der Bemessung ist der gesamte Zulassungsbescheid ETA-15/0784 zu beachten. Zur Verwendung in Mauerwerk gemäß Europäisch Technischer Bewertung ETA-20/0132. Für Kalksandstein KS, Kalksandlochstein KSL und Vollziegel MZ liegt ein Brandschutzgutachten für den Funktionserhalt vor. Verwendung in trockenen Innenräumen. Setzen des Schraubankers mit Tangential Schlagschrauber oder von Hand. Verwendung für : Ankerschienen = 18 mm Schlitzweite Technische Angaben Ø : 7,5 mm Länge L : 40 mm Kopf-Ø : 17 mm Bohrnenn-Ø : 6 mm Klemmbereich t fix : 5 mm empfohlenes Drehmoment : 20 Nm Torxantrieb : T30 Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert Zulassungs-Nr. : ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 691744

Schraubanker mit großem Flachrundkopf und Torxantrieb T30. Zur Verwendung im Funktionserhalt bzw. für Unterdecken mit brandschutztechnischen Anforderungen (Muster-Leitungsanlagen-Richtlinie MLAR 2/2015) bitte Zusatzvorschriften beachten! Anwendung : Anzahl und Anordnung der Schraubanker sind der Ausführungsplanung bzw. dem statischen Nachweis zu entnehmen und einzuhalten. Einbau und Montage gemäß Europäisch Technischer Bewertung ETA-15/0784 bzw. Montageanleitung im gerissenen und ungerissenen Beton C20/25 bis C50/60. Bei der Bemessung ist der gesamte Zulassungsbescheid ETA-15/0784 zu beachten. Zur Verwendung in Mauerwerk gemäß Europäisch Technischer Bewertung ETA-20/0132. Für Kalksandstein KS, Kalksandlochstein KSL und Vollziegel MZ liegt ein Brandschutzgutachten für den Funktionserhalt vor. Verwendung in trockenen Innenräumen. Setzen des Schraubankers mit Tangential Schlagschrauber oder von Hand. Verwendung für : Ankerschienen = 18 mm Schlitzweite Technische Angaben Ø : 7,5 mm Länge L : 50 mm Kopf-Ø : 17 mm Bohrnenn-Ø : 6 mm Klemmbereich t fix : 15 mm empfohlenes Drehmoment : 20 Nm Torxantrieb : T30 Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert Zulassungs-Nr. : ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 691745

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 60 - 64 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 25 pieces
Lieske Part No.: 1315988

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 26 - 30 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 50 pieces
Lieske Part No.: 1315971

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 32 - 36 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 50 pieces
Lieske Part No.: 460741

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 38 - 43 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 25 pieces
Lieske Part No.: 460744

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 68 - 72 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 25 pieces
Lieske Part No.: 1315970

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 99 - 105 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 25 pieces
Lieske Part No.: 1315969

Profile clamp including M 8 stud screw with slotted hexagon head and clamping plate, for clamping to support profiles with parallel flanges or with slanted flanges up to a maximum of 14% inclination and as a supply line to the energy consumers. The fastening materials used can vary depending on the application! Dimensions (approx. dimensions) H x W x L: 57 x 40 x 47 mm Threaded connections: M 6 Load capacity specification vertical nominal load F1: 1.8 kN Load capacity specification vertical nominal load F2: 1.6 kN Flange thickness of the support t: 6 - 35 mm Screw tightening torque: 4 Nm Wrench size: SW 13 Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Sales unit: 25 pieces
Lieske Part No.: 1344802

Profile clamp including M 8 stud screw with slotted hexagon head and clamping plate, for clamping to support profiles with parallel flanges or with slanted flanges up to a maximum of 14% inclination and as a supply line to the energy consumers. The fastening materials used can vary depending on the application! Dimensions (approx. dimensions) H x W x L: 57 x 40 x 47 mm Threaded connections: M 8 Load capacity specification vertical nominal load F1: 1.8 kN Load capacity specification vertical nominal load F2: 1.6 kN Flange thickness of the support t: 6 - 35 mm Screw tightening torque: 4 Nm Wrench size: SW 13 Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 25 pieces
Lieske Part No.: 1345238

Profile clamp including M 8 stud screw with slotted hexagon head and clamping plate, for clamping to support profiles with parallel flanges or with slanted flanges up to a maximum of 14% inclination and as a supply line to the energy consumers. The fastening materials used can vary depending on the application! Dimensions (approx. dimensions) H x W x L: 57 x 40 x 47 mm Threaded connections: M 8 Load capacity specification vertical nominal load F1: 1.8 kN Load capacity specification vertical nominal load F2: 1.6 kN Flange thickness of the support t: 6 - 35 mm Screw tightening torque: 4 Nm Wrench size: SW 13 Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Sales unit: 25 pieces
Lieske Part No.: 185134

NIEDAX - Make: RCM
Ring bolt M
, forged, for the attachment of node chains, galvanized to DIN 5 96
, blue passivated, including two hex nuts. Breaking load: 2
kN Thread: M
opening size of ring: mm NIEDAX model no. RCM type: RCM




ST.
Sales unit: 50 pieces
Lieske Part No.: 526968

NIEDAX - Make: RCM 6 M 6 screw ring, forged, for the attachment of node chains, galvanized to DIN 5 96
, blue passivated, including two hex nuts. Breaking load: 7,3 kN Thread: M 6 opening size of ring: 6.5 mm NIEDAX model no. 6 RCM type: RCM6 item:
ST.
Sales unit: 50 pieces
Lieske Part No.: 843536

NIEDAX - Make: RCM 8 M 8 screw ring, forged, for the attachment of node chains, galvanized to DIN 5 96
, Blue passivated, including two hex nuts. Breaking load:
4.6 kN Thread: M 8 opening size of ring: 8.5 mm NIEDAX model no. RCM 8 Type: RCM8 item:
ST.
Sales unit: 50 pieces
Lieske Part No.: 921499

Hanging bracket, for clipping into the side wall perforation of height-independent cable trays and distribution trays, with connection loop for central suspension using Gripple set hooks, rope or chain. The load-bearing capacity information only applies if the cable tray is sufficiently anchored to the supporting surface. for height-independent cable trays: width 50 mm for distribution trays: RSV 50.050 Dimensions (approx. dimensions) Width B (inside): 54 mm Wire thickness t: 4 Load-bearing capacity F: 0.15 kN Material: steel, wire-galvanized in accordance with DIN EN 10244-2, class D
Sales unit: 50 pieces
Lieske Part No.: 749589

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the cable's terminal space for fastening a cable. Please observe additional regulations for use in functional maintenance! Dimensions (approx. dimensions) W x L: 12 x 35 mm Internal connection thread: M 6 for cable Ø: 10 - 11 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material: Steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no.: SAS 10 V
Sales unit: 50 pieces
Lieske Part No.: 1342451

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation conduits in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric electrical installation conduit. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 12 x 37 mm Internal connection thread : M 6 for cable Ø : 11 - 13 mm for metric electrical installation conduits in accordance with DIN EN 60423 : M 12 Material : steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material : steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no. : SAS 12V
Sales unit: 50 pieces
Lieske Part No.: 1342059

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the cable's terminal space for fastening a cable. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L: 12 x 39 mm Internal connection thread: M 6 for cable Ø: 13 - 15 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material: Steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no.: SAS 14 V
Sales unit: 50 pieces
Lieske Part No.: 1342415

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation conduits in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric electrical installation conduit. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 12 x 41 mm Internal connection thread : M 6 for cable Ø : 15 - 17 mm for metric electrical installation conduits in accordance with DIN EN 60423 : M 16 Material : steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material : steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no. : SAS 16V
Sales unit: 50 pieces
Lieske Part No.: 1342441

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation conduits in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric electrical installation conduit. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 12 x 51 mm Internal connection thread : M 6 for cable Ø : 25 - 27 mm for metric electrical installation conduits in accordance with DIN EN 60423 : M 25 Material : steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material : steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no. : SAS 26 V
Sales unit: 50 pieces
Lieske Part No.: 1342454

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the cable's terminal space for fastening a cable. Please observe additional regulations for use in functional maintenance! Dimensions (approx. dimensions) W x L: 12 x 56 mm Internal connection thread: M 6 for cable Ø: 28 - 30 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material: Steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no.: SAS 30 V
Sales unit: 50 pieces
Lieske Part No.: 1342453

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric pipe. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 16 x 69 mm Internal connection thread : M 6 for cable Ø : 29 - 38 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 32 Material : Steel, galvanized in accordance with DIN EN ISO 2081, thick-film passivated Screw material : Steel, galvanized in accordance with DIN EN ISO 4042, thick-film passivated Niedax model no. : SAS38
Sales unit: 25 pieces
Lieske Part No.: 231268

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken to ensure that the connection thread of the push-through anchor does not protrude into the cable's terminal space, for fastening a cable or a metric pipe. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 16 x 79.5 mm Connection internal thread : M 6 for cable Ø : 38 - 47 mm for metric electrical installation pipes according to DIN EN 60423 : M 40 Material : Steel, galvanized according to DIN EN ISO 2081, thick-layer passivated Screw material : Steel, galvanized according to DIN EN ISO 4042, thick-layer passivated Niedax model no. : SAS 47
Sales unit: 20 pieces
Lieske Part No.: 207435

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable. For fastening a cable or a metric pipe. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 18 x 89 mm Internal connection thread : M 6 for cable Ø : 47 - 55 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 50 Material : Steel, galvanized in accordance with DIN EN ISO 2081, thick-film passivated Screw material : Steel, galvanized in accordance with DIN EN ISO 4042, thick-film passivated Niedax model no. : SAS55
Sales unit: 20 pieces
Lieske Part No.: 266879

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric pipe. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 18 x 100 mm Internal connection thread : M 6 for cable Ø : 55 - 63 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 63 Material : Steel, galvanized in accordance with DIN EN ISO 2081, thick-film passivated Screw material : Steel, galvanized in accordance with DIN EN ISO 4042, thick-film passivated Niedax model no. : SAS60
Sales unit: 20 pieces
Lieske Part No.: 736666

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the cable's terminal space for fastening a cable. Please observe additional regulations for use in functional maintenance! Dimensions (approx. dimensions) W x L: 12 x 33 mm Internal connection thread: M 6 for cable Ø: 7.5 - 10 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material: Steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no.: SAS 8 V
Sales unit: 50 pieces
Lieske Part No.: 1342452

Screw spacing clamp, heavy, for screwing on, with fastening hole. Can be used for: Machine installation pipe MI 60... Machine installation pipe MIG 60... Installation pipe connection MIA 60... Dimensions (approx. dimensions) Width W x Length L: 30 x 110 mm Fastening hole Ø: 9 mm for pipe Ø: 60 mm Material: Stainless steel, material no. 1.4301, 1.4303 Screw material: Stainless steel, material no. 1.4301, 1.4303 Niedax model no.: SASS 60 E3
Sales unit: 20 pieces
Lieske Part No.: 1327214

S-hook for link chain: KG... KF... KN... Dimensions (approx. dimensions) H: 45 mm Material thickness t: 5 mm Load capacity F: 0.3 kN Material: Steel, galvanized/chromated according to DIN 50021
Sales unit: 100 pieces
Lieske Part No.: 912685

S-hook for link chain: KG... KF... KN... Dimensions (approx. dimensions) H: 35 mm Material thickness: 4 mm Material: stainless steel, material no. 1.4401, 1.4404
Sales unit: 100 pieces
Lieske Part No.: 147906

NIEDAX - Make: SHS 30
A holder from steel strip galvanized to DIN EN 10346, for the installation of cable bundles to the wall and ceiling, suitable for 30 cables (NYM 3x1.5 mmý). For use in the functional integrity please follow additional rules!

Clear internal dimensions H x W: 81 x 50 mm NIEDAX model no. SHS 30 Type: SHS30




Item: 100 ST.
Lieske Part No.: 286667

Collective holder with high mechanical strength for laying cable bundles on walls and ceilings. For use in functional maintenance or for suspended ceilings with fire protection requirements (model cable system guideline MLAR 2/2015), please observe additional regulations! Dimensions (approx. dimensions) clear internal dimensions H x W: 114.5 x 90 mm Material: steel, strip galvanized according to DIN EN 10346
Sales unit: 10 pieces
Lieske Part No.: 266486

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 20 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 231309

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 25 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 532836

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 35 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 100 pieces
Lieske Part No.: 1426291

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 40 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 231323

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 50 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 1315777

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 12 Screw length: 100 mm Strength class: 8.8 Screw tightening torque: 84 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 338376

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 12 Screw length: 120 mm Strength class: 8.8 Screw tightening torque: 84 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 231298

Hexagon head screw with slot similar to DIN EN ISO 4018, head with slot according to DIN 962. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 8 Screw length: 12 mm Strength class: 4.6 Screw tightening torque: 9.1 Nm Wrench size: SW 11 Material: Steel, galvanized according to DIN EN ISO 4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 537581

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 8 Screw length: 25 mm Strength class: 8.8 Screw tightening torque: 24.6 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 100 pieces
Lieske Part No.: 1426290