Installation Material

2-part cable tie with EdgeClip, pre-assembled. The head of the tie can be moved to the optimal bundle position. Type EC9, EC10, EC21 and EC22 for bundle diameters from 1 mm. For edges of 1 - 3 mm. Elements from the EdgeClip series are a very good alternative wherever holes and weld studs cannot be drilled and adhesives cannot be used due to higher temperatures. The EdgeClip family is used for bundling and fastening cable harnesses and hoses, primarily in the automotive, construction and electrical industries, as well as in cable harness production.
Sales unit: 500 pieces
Lieske Part No.: 140314

Type: T30REC4B PA66HS,PA66HIRHS BK 500 ST

Sales unit: 500 pieces
Lieske Part No.: 288758

Type: T30REC4A PA66HS, PA66HIRHS BK ST 500 item: 500 ST.
Sales unit: 500 pieces
Lieske Part No.: 365766

2-part cable tie with EdgeClip, pre-assembled. The head of the tie can be moved to the optimal bundle position. Type EC9, EC10, EC21 and EC22 for bundle diameters from 1 mm. For edges of 1 - 3 mm. Elements from the EdgeClip series are a very good alternative wherever holes and weld studs cannot be drilled and adhesives cannot be used due to higher temperatures. The EdgeClip family is used for bundling and fastening cable harnesses and hoses, primarily in the automotive, construction and electrical industries, as well as in cable harness production.
Sales unit: 500 pieces
Lieske Part No.: 2054013

2-teiliger Kabelbinder mit EdgeClip, vormontiert. Der Kopf des Binders kann in optimale Bündelposition gebracht werden. Typ EC9, EC10, EC21 und EC22 für Bündeldurchmesser ab 1 mm. Für Kanten von 1 - 3 mm. Elemente aus der EdgeClip-Serie sind eine sehr gute Alternative überall dort, wo Lochbohrungen und Schweißbolzen nicht realisierbar und Kleber aufgrund höherer Temperaturen nicht einsetzbar sind. Anwendung findet die EdgeClip-Familie zur Bündelung und Befestigung von Kabelbäumen und Schläuchen überwiegend in der Automobil-, Bau- und Elektroindustrie sowie in der Kabelbaumfertigung.
Sales unit: 500 pieces
Lieske Part No.: 757987

2-part cable tie with EdgeClip, pre-assembled. The head of the tie can be moved to the optimal bundle position. Type EC9, EC10, EC21 and EC22 for bundle diameters from 1 mm. For edges of 1 - 3 mm. Elements from the EdgeClip series are a very good alternative wherever holes and weld studs cannot be drilled and adhesives cannot be used due to higher temperatures. The EdgeClip family is used for bundling and fastening cable harnesses and hoses, primarily in the automotive, construction and electrical industries, as well as in cable harness production.
Sales unit: 500 pieces
Lieske Part No.: 183758

2-part cable tie with slatted base, pre-assembled. The head of the tie can be moved to the optimal bundle position. Easy assembly, no tools required. Protects against dirt and dust penetration through plates. Various sheet thicknesses can be used with a single slatted base part. Also for blind holes with thread. These fastening ties are used wherever efficient work combined with high holding forces is required. They can be used in control cabinet and vehicle construction, for example.
Sales unit: 500 pieces
Lieske Part No.: 1051654

2-part cable tie with slatted base, pre-assembled. The head of the tie can be moved to the optimal bundle position. Easy assembly, no tools required. Protects against dirt and dust penetration through plates. Various sheet thicknesses can be used with a single slatted base part. Also for blind holes with thread. These fastening ties are used wherever efficient work combined with high holding forces is required. They can be used in control cabinet and vehicle construction, for example.
Sales unit: 500 pieces
Lieske Part No.: 1232045

Type: T50RFT6-MC5-BK-D1

Sales unit: 500 pieces
Lieske Part No.: 873934

2-part cable tie with slatted base, pre-assembled. The head of the tie can be moved to the optimal bundle position. Easy assembly, no tools required. Protects against dirt and dust penetration through plates. Various sheet thicknesses can be used with a single slatted base part. Also for blind holes with thread. These fastening ties are used wherever efficient work combined with high holding forces is required. They can be used in control cabinet and vehicle construction, for example.
Sales unit: 500 pieces
Lieske Part No.: 1314990

Quantity: 500 ST.
Sales unit: 500 pieces
Lieske Part No.: 969211

Easy installation, no tools required. Expansion anchors lock into place with an audible and tangible click. High pull-out and holding force, even when subjected to loads from different directions. Plates protect against dirt and dust penetration. KSFT variants with rounded expansion anchors for minimized installation height. The T50SST5 variant offers support against axial displacement. Fastening ties with expansion anchors are used to securely bundle and fasten cable harnesses and hoses in control cabinet construction, the automotive industry and the aerospace industry. This fastening solution is used to secure cable harnesses. We offer a variety of plate thicknesses and hole sizes for every application.
Sales unit: 500 pieces
Lieske Part No.: 2092998

2-teiliger Kabelbinder mit Spreizanker als Fußteil, vormontiert. Der Kopf des Binders kann in die optimale Bündelposition gebracht werden. Einfache Montage, werkzeugfrei. Spreizanker verrasten hör- und fühlbar. Hohe Auszugs- und Haltekraft, auch bei Belastungen aus unterschiedlichen Richtungen. Schützt vor eindringendem Schmutz und Spritzwasser durch Teller. Diese Befestigungsbinder finden überall dort Anwendung, wo rationelles Arbeiten verbunden mit hohen Haltekräften gefordert ist. Sie werden u.a. im Automobilbereich eingesetzt und überall dort, wo Leitungen sicher geführt werden sollen.
Sales unit: 500 pieces
Lieske Part No.: 687527

Type: BMS-100

Lieske Part No.: 140455

Type: SAC1 ST WH 100 ST

Sales unit: 100 pieces
Lieske Part No.: 248424

Type: LKCRF1 PA66 BK 500 ST item: ST 13000.
Sales unit: 13000 pieces
Lieske Part No.: 428642

Selbstklebender Sockel zur schnellen und einfachen Montage. Befestigungslösung ohne zusätzlichen Kabelbinder. Bietet Potential zur Prozessoptimierung. Entwickelt, um Schläuche, Leitungen und Kabelbündel zu halten. Verschiedene Größen für verschiedene Bündeldurchmesser erhältlich. Es können zwei Typen von Kleber angeboten werden. Die RA Befestigungssockel sind eine ideale Lösung für alle Anwendungen, die schwer zugänglich sind oder bei denen nur selbstklebende Befestigungslösungen eingesetzt werden dürfen und das Schrauben inakzeptabel ist. RA Befestigungssockel benötigen keinen zusätzlichen Kabelbinder. Sie bieten Potential zur Prozessoptimierung in der Automobilindustrie, im Bereich Nutzfahrzeuge oder im Gewerbebau.
Sales unit: 100 pieces
Lieske Part No.: 500218

Design enables secure form-fitting to the bundled goods. Conventional cable clamps can be replaced. Stocking different clamp sizes is no longer necessary. For heavy-duty cable ties up to 13.5 mm wide. Bundles can be maintained by simply replacing cable ties. Developed for the automotive and truck industries, Heavy Duty Mounts (HDM) are used wherever robust, secure and permanent bundling is required. Rail vehicle construction and the defense and agricultural industries are also focus markets.
Lieske Part No.: 1131197

Clamps that are pushed onto an edge. Reopenable fastening elements with EdgeClip. Also for subsequent installation. Low-vibration guidance of even larger pipes and cables. Can be closed with one hand, noticeable locking. The covers can be opened for maintenance or subsequent installation. EC27 also secures smaller bundles rattling-free using a spring. EdgeClips are used in the automotive and electrical industries when holes cannot be drilled or no other fastening points are available.
Sales unit: 500 pieces
Lieske Part No.: 2058362

Biegsamer Metallbügel für eine Vielzahl von Bündeln. Kostengünstige Befestigungslösung ohne Kabelbinder. Einfache Installation auf glatten, sauberen Oberflächen. Die SAC-Serie ist eine ideale Lösung für alle Anwendungen, die schwer zugänglich sind oder bei denen nur selbstklebende Befestigungslösungen eingesetzt werden dürfen. Typische Anwendungen finden sich bei der Herstellung von Haushaltsgeräten oder im Wohnwagenbau.
Sales unit: 1000 pieces
Lieske Part No.: 1276638

Screwable mounting base. Easy installation using standard screws. Particularly suitable for secure hold in the event of vibrations. The cable tie can be looped in from four sides for quick and flexible installation. The main areas of application are in control cabinet construction, in industrial series production and in areas where the large base plate must ensure stable fastening.
Sales unit: 100 pieces
Lieske Part No.: 2057130

Self-adhesive mounting base. Synthetic rubber adhesive for universal applications. Largest possible adhesive surface. 4-way looping direction of the cable ties for quick and flexible assembly. The main areas of application for the self-adhesive TY-ITS bases are in control cabinet construction, in industrial series production and in areas where the large base plate must ensure stable fastening, but screw fastening is not possible.
Sales unit: 12000 pieces
Lieske Part No.: 2056978

Self-adhesive mounting base. Synthetic rubber adhesive for universal applications. Largest possible adhesive surface. 4-way looping direction of the cable tie for quick and flexible installation. Can also be fixed quickly and easily with a screw. The main areas of application for the self-adhesive TY-ITS bases are in control cabinet construction, in industrial series production and in areas where the large base plate must ensure stable fastening, but screw fastening is not possible.
Sales unit: 200 pieces
Lieske Part No.: 2056979

Fast and easy fixing with a screw. The main areas of application for the self-adhesive TY-ITS bases are in control cabinet construction, in industrial series production and in areas where the large base plate must ensure stable fastening, but screw fastening is not possible.
Sales unit: 6000 pieces
Lieske Part No.: 2056980

Push und Click-Anwendung zur einfachen Befestigung von Leitungen. Kupplungststücke der IAHC-Halter ermöglichen Verbindung mehrerer Halter miteinander. Halter wird in die spezifizierte Lochbohrung eingeklickt. AHC( )SS und AHC( )SB können auf einen 5mm Bolzen gesteckt werden. IAHC( )T verfügen nur über Kupplungsstücke. Diese Halter sind eine schnelle und einfache Methode, um Leitungen zu fixieren und zu bündeln. Ursprünglich für die Automobilindustrie entwickelt, finden sich auch in diversen anderen Industriezweigen Anwendungen für diese praktischen Halter.
Sales unit: 400 pieces
Lieske Part No.: 687529

EdgeClips can be installed by simply sliding them on. The integrated metal clip holds the clip firmly on the edge. The metal clip is made of specially coated spring steel. If neither drilling nor adhesive can be used.
Sales unit: 500 pieces
Lieske Part No.: 2058363

Design enables secure form-fitting to the bundled goods. Conventional cable clamps can be replaced. Stocking different clamp sizes is no longer necessary. For heavy-duty cable ties up to 13.5 mm wide. Bundles can be maintained by simply replacing cable ties. Developed for the automotive and truck industries, Heavy Duty Mounts (HDM) are used wherever robust, secure and permanent bundling is required. Rail vehicle construction and the defense and agricultural industries are also focus markets.
Lieske Part No.: 1346802

EdgeClips can be installed by simply sliding them on. The integrated metal clip holds the clip firmly on the edge. The metal clip is made of specially coated spring steel. If neither drilling nor adhesive can be used.
Sales unit: 1000 pieces
Lieske Part No.: 2058364

Flaches Design für Anwendungen mit engen Platzverhältnissen. Selbstklebende Sockel zur schnellen und einfachen Montage. Wird ohne zusätzlichen Kabelbinder verwendet. Bietet Potential zur Prozessoptimierung. Verschiedene Größen für verschiedene Bündeldurchmesser erhältlich. Kostengünstige Lösung und einfache Installation. Geeignet für Anwendungen auf glatten, sauberen Oberflächen. Die selbstklebenden Sockel der RB-Serie bieten eine größere Führungsfreiheit und reduzieren das Korrosionsrisiko im Vergleich zu Schraubbefestigungen. Sie eignen sich hervorragend für die werkzeuglose Installation und können wieder geöffnet und erneut verwendet werden. Dies ist vor allem dann hilfreich, wenn Bündel schnell und einfach ausgetauscht werden müssen. Die RB-Serie kann ohne Kabelbinder verwendet werden und bietet Prozessoptimierungspotential für eine Vielzahl von Anwendungen.
Sales unit: 200 pieces
Lieske Part No.: 1280994

Flaches Design für Anwendungen mit engen Platzverhältnissen. Selbstklebende Sockel zur schnellen und einfachen Montage. Wird ohne zusätzlichen Kabelbinder verwendet. Bietet Potential zur Prozessoptimierung. Verschiedene Größen für verschiedene Bündeldurchmesser erhältlich. Kostengünstige Lösung und einfache Installation. Geeignet für Anwendungen auf glatten, sauberen Oberflächen. Die selbstklebenden Sockel der RB-Serie bieten eine größere Führungsfreiheit und reduzieren das Korrosionsrisiko im Vergleich zu Schraubbefestigungen. Sie eignen sich hervorragend für die werkzeuglose Installation und können wieder geöffnet und erneut verwendet werden. Dies ist vor allem dann hilfreich, wenn Bündel schnell und einfach ausgetauscht werden müssen. Die RB-Serie kann ohne Kabelbinder verwendet werden und bietet Prozessoptimierungspotential für eine Vielzahl von Anwendungen.
Sales unit: 100 pieces
Lieske Part No.: 176049

For parallel guidance of two bundles that can be rotated 360° relative to each other. The H-design ensures a good form fit to the bundled goods. The head of the tie can be brought into the optimal bundle position. For cable ties up to 12.7 mm wide. Also for subsequent assembly of bundled goods. These elements were developed for the automotive and truck industries, but can be used in any area where a connection of two bundles and a defined distance are required.
Lieske Part No.: 2058192

Quantity: 10000 ST.
Sales unit: 100 pieces
Lieske Part No.: 960496

Curved design for additional cable protection. Easy installation using a screw or bolt. High security, especially in areas with high vibration. Various sizes and materials available. Specially designed for securing heavy cable bundles, these mounting bases can be used in many industries from agriculture to truck manufacturing. They offer a very secure fastening and can be used in combination with cable ties up to 8.3 mm wide.
Sales unit: 100 pieces
Lieske Part No.: 1133119

Easy installation, no tools required. Protects against dirt and dust penetration through plates. Defined bundle diameter. For subsequent installation of bundled goods. This fastening element enables flexible processing of cables and hoses. The bundled goods are simply pressed into the clip and held there by slats. It is possible to accommodate several cables and add cables later. The clip also allows radial twisting of the bundled goods.
Sales unit: 5000 pieces
Lieske Part No.: 2058365

Fastening elements for corrugated pipes for nominal widths of 4.5-17 mm. For M6 welding studs. Soft-push mechanism for easy, tool-free assembly. Safe guidance of the pipe by simply clicking in. Axial displacement is prevented by the profile in the corrugated pipe holder. Fastening element can be removed by unscrewing the welding stud. These holders are used in the automotive industry, cable assembly and electrical industry, for example. Due to their simple and time-saving assembly, they have become established wherever corrugated hoses and corrugated pipes need to be fastened quickly and securely.
Sales unit: 500 pieces
Lieske Part No.: 1131195

Compact, flat design. Suitable for applications with minimal space. Can be combined with cable ties up to 5 mm wide. 4-way looping direction for use in line or at a 90° angle. CTAM sockets made of PEEK are used in applications where special material properties are required. On the one hand, these sockets can be installed in areas with high continuous temperatures of up to + 240 °C, e.g. for attachments to the exhaust system or in the engine compartment. In the semiconductor industry, products made of PEEK are used in test laboratories, among other things, to minimize the influence of external gases. Due to the good resistance to radiation, the sockets are suitable for use in medical technology/X-ray technology. The good resistance to acids and other chemicals speaks for use in the chemical industry. CTAM sockets can be an excellent replacement for previous metal solutions.
Sales unit: 100 pieces
Lieske Part No.: 982322

Kompakte, flache Bauweise. Kombinierbar mit Kabelbindern bis zu 5 mm Breite. 4-Wege-Einschlaufrichtung. Zum Einsatz kommen die CTAM-Sockel aus dem Werkstoff PEEK bei Anwendungen, wo besondere Materialeigenschaften gefordert sind. Einerseits können diese Sockel in Bereichen mit hoher Dauertemperatur bis + 240 °C verbaut werden, z. B. bei Befestigungen am Abgassystem oder im Motorraum. In der Halbleiterindustrie werden Produkte aus PEEK u. a. in Testlaboren eingesetzt, um den Einfluss von fremden Ausgasungen zu minimieren. Aufgrund der guten Strahlenresistenz eignen sich die Sockel für die Verwendung in der Medizintechnik/Röntgentechnik. Für den Einsatz in der chemischen Industrie spricht die gute Beständigkeit gegen Säuren und andere Chemikalien. CTAM-Sockel können hervorragend bisherige Metallösungen ersetzen.
Sales unit: 5000 pieces
Lieske Part No.: 948700

Easy installation without damaging the surface of the carrier. Fast maintenance of the bundle by simply replacing the cable tie. The head of the tie can be brought into the optimal bundle position. Can be used with various sheet thicknesses. These elements were developed for the automotive and truck industry, but can be used in any area where a firm and permanent fastening is required. With the carrier clamps, cables, lines and hydraulic lines can be easily guided and fixed in agricultural machinery construction, the rail industry, but also in shipbuilding and industrial buildings.
Sales unit: 200 pieces
Lieske Part No.: 1055128

Easy installation without damaging the surface of the carrier. Fast maintenance of the bundle by simply replacing the cable tie. The head of the tie can be brought into the optimal bundle position. Can be used with various sheet thicknesses. These elements were developed for the automotive and truck industry, but can be used in any area where a firm and permanent fastening is required. With the carrier clamps, cables, lines and hydraulic lines can be easily guided and fixed in agricultural machinery construction, the rail industry, but also in shipbuilding and industrial buildings.
Sales unit: 200 pieces
Lieske Part No.: 1055129

Low profile design for applications where space is limited. Self-adhesive bases for quick and easy installation. Used without additional cable ties. Offers potential for process optimization. Various sizes available for different bundle diameters. Cost-effective solution and easy installation. Suitable for applications on smooth, clean surfaces. The RB series self-adhesive bases offer greater routing freedom and reduce the risk of corrosion compared to screw fastenings. They are ideal for tool-free installation and can be reopened and reused. This is especially useful when bundles need to be replaced quickly and easily. The RB series can be used without cable ties and offers process optimization potential for a wide range of applications.
Sales unit: 1400 pieces
Lieske Part No.: 1129381

The combination of base and cable tie means that a wide range of different clamp diameters can be replaced. Cable ties can be looped in from two sides. Made from stainless steel grade SS316 (V4A). Excellent chemical and temperature resistance. Quick and easy processing. Robust and permanent fixation of all types of bundles. The P-Mount stainless steel bases are suitable for reliable fastening of cables, hoses, protective pipes and pipelines in extreme environments. In combination with stainless steel cable ties from the MBT-S and MBT-H series, they offer a system solution in the areas of shipbuilding, oil and gas production, industrial machinery and vehicles as well as in the food industry and energy supply including renewable energies.
Sales unit: 100 pieces
Lieske Part No.: 1135080

The combination of base and cable tie means that a wide range of different clamp diameters can be replaced. Cable ties can be looped in from two sides. Made from stainless steel grade SS316 (V4A). Excellent chemical and temperature resistance. Quick and easy processing. Robust and permanent fixation of all types of bundles. The stainless steel bases of the SSPC series, in combination with stainless steel cable ties, enable reliable fastening of cables, hoses, protective pipes and pipelines in extreme environments. The bases can be used with metal cable ties up to a width of 10 mm. A first-class system solution for shipbuilding, oil and gas production, industrial machinery and vehicles, as well as for the food industry and energy supply.
Sales unit: 100 pieces
Lieske Part No.: 1135079

Edelstahlsockel SSPC Serie, SS316 (V4A), Artikelnummer: 151-00839
Edelstahlsockel P-mount (Befestigungsloch 6mm)

Eigenschaften:

2-Wege Einschlaufrichtung für Edelstahlkabelbinder
Hergestellt aus Edelstahl der Güte SS316 (V4A)
Hervorragende chemische Beständigkeit
Schnelle und einfache Verarbeitung
Hohe Temperaturbeständigkeit
Robuste und dauerhafte Fixierung von Kabeln, Schläuchen, Schutzrohren und Rohrleitungen



Anwendung
Die Edelstahlsockel P-Mount eignen sich für eine zuverlässige Befestigung von Kabeln, Schläuchen, Schutzrohren und Rohrleitungen in extremer Umgebung. In Kombination mit Edelstahlkabelbindern bis zu einer Breite von 10 mm bieten sie eine Systemlösung in den Bereichen Schiffbau, Öl- und Gasförderung, Industriemaschinenbau und -fahrzeuge sowie in der Lebensmittelindustrie und der Energieversorgung inklusive der erneuerbaren Energien.
Edelstahlsockel SSPC Serie, SS316 (V4A) ist für folgende Industrie-Branchen geeignet

Nahrungsmittelindustrie
Luft- und Raumfahrt
Automobilindustrie
Chemische Industrie
Verteidigungsindustrie
Elektroinstallation
Elektrogroßhandel
Elektronikindustrie
Offshore
Schienenfahrzeugbau
Schiffbau
Solaranlagen
Telekommunikation
Windkraftanlagen
Sales unit: 100 pieces
Lieske Part No.: 172140

Easy installation without damaging the surface of the carrier. Fast maintenance of the bundle by simply replacing the cable tie. The head of the tie can be brought into the optimal bundle position. Can be used with various sheet thicknesses. These elements were developed for the automotive and truck industry, but can be used in any area where a firm and permanent fastening is required. With the carrier clamps, cables, lines and hydraulic lines can be easily guided and fixed in agricultural machinery construction, the rail industry, but also in shipbuilding and industrial buildings.
Sales unit: 200 pieces
Lieske Part No.: 1055130

Gebogenes Design für zusätzlichen Kabelschutz. Einfache Installation mittels Schraube oder Bolzen. Hohe Sicherheit, vor allem in Bereichen mit starker Vibration. Verschiedene Größen und Materialien verfügbar. Speziell für die Befestigung schwerer Kabelbündel konzipiert, können diese Befestigungssockel in vielen Branchen von der Landwirtschaft bis zur LKW-Fertigung eingesetzt werden. Sie bieten eine sehr sichere Befestigung und können in Kombination mit Kabelbindern bis 8,3 mm Breite verwendet werden.
Sales unit: 56000 pieces
Lieske Part No.: 2057131

Striking blue for easy visual recognition. Compact design with a slight curvature. Offers a secure hold for the bundled goods. Can be detected by metal devices (result depends on the respective application). Easy installation using a screw. Can be combined with MCT / MCTS cable ties. Particularly suitable for a secure hold in the event of vibrations. Greatly reduced risk of contamination (e.g. of food). Can be used as part of the HACCP process*. MCKR bases in a curved design are used wherever cables and lines with a larger diameter need to be attached. Even in applications with high vibrations, such as production and packaging systems within the food industry, these bases offer a secure hold for the bundled goods.
Sales unit: 100 pieces
Lieske Part No.: 1131194

Das integrierte Design ermöglicht ein einfaches Einsetzen von Hand.. Die Plattendicke von 1,0 bis 3,0 mm ermöglicht eine Vielzahl von Anwendungen.. Das Design mit doppelter Kompression kann bis zu 2 Drähte oder Kabel unterschiedlicher Größe aufnehmen.. Bietet eine hohe Auszugskraft, um extremen Bedingungen standzuhalten.. Der Heavy Duty Metal Edge Clip von HellermannTyton ist eine hervorragende Alternative für das Management von Kabeln und PV-Kabeln, wenn Kunststoffbefestigungen nicht die bevorzugte Methode sind. Der Metal Edge Clip wurde für ein müheloses Einsetzen entwickelt und verfügt über eine hohe Auszugskraft, die extreme Umgebungen toleriert und die Sicherheit bietet, dass die Kabel sicher auf einem Paneel befestigt sind. Der Metal Edge Clip ist einfach zu installieren und kann mit einem Schlitzschraubendreher leicht wieder entfernt werden.
Sales unit: 100 pieces
Lieske Part No.: 705721

Striking blue for easy visual recognition. Compact, flat design. Detectable via metal devices (result depends on the respective application). 4-way looping direction for quick and flexible installation. Even individual pieces can be detected due to the homogeneous distribution of the metal particles. Greatly reduced risk of contamination (e.g. of food). Can be used as part of the HACCP process*. These bases are characterized above all by their compact and flat design and are an ideal addition to our MCTS cable ties. The homogeneously distributed metal components make the product optimally detectable and therefore predestined for use in the food and pharmaceutical industries. With the MCCTAM bases, the cable tie can be looped in all 4 directions, which means that the bundle can run in two directions.
Sales unit: 100 pieces
Lieske Part No.: 2058366

Clearly defined cable routing with up to three bundles. Simple fastening using welded bolts. Inner bore M8 and outer diameter 15 mm, 8 mm recess. Maximum bundle protection thanks to smooth surface. Weight reduction compared to a metal holder. Thermal, electrical and vibration decoupling. Made of glass fiber reinforced plastic, corrosion-free. Maintenance of the bundled goods possible by simply replacing the cable ties. This 3-way spacer for fastening ties was developed to guide up to 3 bundles safely.
Sales unit: 500 pieces
Lieske Part No.: 468064

Striking blue for easy visual recognition. Compact design with a slight curvature. Offers a secure hold for the bundled goods. Can be detected by metal devices (result depends on the respective application). Easy installation using a screw. Can be combined with MCT / MCTS cable ties. Particularly suitable for a secure hold in the event of vibrations. Greatly reduced risk of contamination (e.g. of food). Can be used as part of the HACCP process*. MCKR bases in a curved design are used wherever cables and lines with a larger diameter need to be attached. Even in applications with high vibrations, such as production and packaging systems within the food industry, these bases offer a secure hold for the bundled goods. They can be combined with cable ties up to 8.3 mm wide.
Sales unit: 100 pieces
Lieske Part No.: 149650