Installation Material

Terminal covers KA165 are used to increase the protection class to IP20 for MS/MO165
Sales unit: 10 pieces
Lieske Part No.: 326531

OTS40T3 Terminal cover snap-on mounting transparent plastic
Lieske Part No.: 472913

The 3-pole contactors of the AFS series are designed for machine safety applications. They are supplied with a permanently mounted, color-coded, side auxiliary contact block and are therefore ideal for monitoring and controlling power circuits with motors, slightly inductive or non-inductive loads. The integrated auxiliary contacts are positively guided and designed as mirror contacts in accordance with IEC60947-5-1 Appendix L. They also have built-in overvoltage protection and do not require any additional suppressors. Minimum switching capacity of the auxiliary contacts 12V / 3mA, with a failure rate of 10-7 in accordance with IEC 60947-5-4.
Lieske Part No.: 2022730

M16/12.P Screw Clamp Terminal Blocks - Ground - Green-Yellow,16mm² RatedCrossSection, 12mm Spacing G32, TH 35-7.5, TH 35-15 Rail
Lieske Part No.: 988206

As an interface, interface relays connect the electronic control level, for example PLC, with the level of the sensors/actuators. They perform various functions: switching of direct or alternating voltage loads with different ohmic, inductive and capacitive components, switching in the voltage range from a few mV to 250 V, switching in the current range from a few mA to 16 A, amplifying weak control signals, potential isolation of control and load circuits and signal multiplication. The CR-P series has 9 different coil voltages with 1-2 changeover contacts. Two base variants are available: standard base and logical base. Pluggable function modules such as reverse polarity protection / freewheeling diode, LED module, RC elements, overvoltage protection or time modules expand the areas of application of the pluggable PCB relays.
Lieske Part No.: 595393

The CMS current sensors are part of the ABB energy monitoring InSite with the control units SCU100 and SCU200. The sensors measure TRMS, AC and DC currents (instantaneous, min/max and hold values) and transmit these values to the InSite control unit via a 4-pin ribbon cable.
The sensors can be used with the protection and switching devices of the ABB System pro M compact® and enable installation in the rear terminal of the protection device. The closed solid-core sensors have a high measurement accuracy of 0.5% and are less sensitive to EMC effects from adjacent final circuits.
Lieske Part No.: 875569

The CMS current sensors are part of the ABB energy monitoring InSite with the control units SCU100 and SCU200. The sensors measure TRMS, AC and DC currents (instantaneous, min/max and hold values) and transmit these values to the InSite control unit via a 4-pin ribbon cable.
The sensors can be used with the protection and switching devices of the ABB System pro M compact® and enable installation in the rear terminal of the protection device. The closed solid-core sensors have a high measurement accuracy of 0.5% and are less sensitive to EMC effects from adjacent final circuits.
Lieske Part No.: 875562

The CMS current sensors are part of the ABB energy monitoring InSite with the control units SCU100 and SCU200. The sensors measure TRMS, AC and DC currents (instantaneous, min/max and hold values) and transmit these values to the InSite control unit via a 4-pin ribbon cable.
The sensors can be used with the protection and switching devices of the ABB System pro M compact® and enable installation in the rear terminal of the protection device. The closed solid-core sensors have a high measurement accuracy of 0.5% and are less sensitive to EMC effects from adjacent final circuits.
Lieske Part No.: 875555

Cable marking sheet for self-labeling, 3 markers / sheet, dimensions 69 x 25 x 19mm
Sales unit: 100 pieces
Lieske Part No.: 1425141

Cable marking sheet for self-labeling, 3 markers / sheet, dimensions 127 x 25 x 25mm
Sales unit: 100 pieces
Lieske Part No.: 1425142

Cable ties with steel nose closure, robust, 15,200 x 12.7 mm, 1110 N, black, Acetal ®*
Sales unit: 5 pieces
Lieske Part No.: 1311301

Deltec, locking head, double locking made of durable and weather-resistant acetate, the locking is made of a corrosion-resistant copper alloy according to marine classification, 21.6 x 19.1 x 12.6mm, black, PU 25
Sales unit: 25 pieces
Lieske Part No.: 1311327

Deltec, pre-assembled cable ties with double locking heads made of durable, weather-resistant acetate, 254 x 12.7mm, UV-resistant, halogen-free, excellent resistance to moisture and salt water environments, PU 50
Sales unit: 50 pieces
Lieske Part No.: 1325385

Deltec, practical set consisting of 5 small spools of cable tape á 15.2m and 150 locking heads for efficient work on site, PU 1
Sales unit: 150 pieces
Lieske Part No.: 1583722

Deltec, practical set consisting of 10 small spools of cable tape á 15.2m and 300 locking heads for efficient work on site, PU 1
Sales unit: 80 pieces
Lieske Part No.: 1583723

Spacer, robust, for pressing in, for cable ties width up to 12.7 mm, black, polypropylene UV-resistant
Lieske Part No.: 300621

Deltec, pre-assembled cable ties with double locking heads made of durable, weather-resistant acetate, 406.4 x 12.7mm, UV-resistant, halogen-free, excellent resistance to moisture and salt water environments, VPE
Sales unit: 50 pieces
Lieske Part No.: 1325384

Straight metal screw connection, for liquid-tight metal protective hoses, made of galvanized cast steel with chrome-plated surface, inner sleeve made of polyamide, nominal size 3/8 inch or 16 mm, thread connection NPT 1/2 inch, protection class IP67
Sales unit: 100 pieces
Lieske Part No.: 338840

Straight metal screw connection, for liquid-tight metal protective hoses, made of galvanized cast steel with chrome-plated surface, inner sleeve made of polyamide, nominal size 3/4 inch or 25 mm, thread connection NPT 3/4 inch, protection class IP67
Lieske Part No.: 338834

45° - angled metal screw connection, for liquid-tight metal protective hoses, made of galvanized cast steel with chrome-plated surface, inner sleeve made of polyamide, nominal size 1/2 inch or 20 mm, threaded connection NPT 1/2 inch, protection class IP67
Sales unit: 50 pieces
Lieske Part No.: 297255

Straight metal screw connection, for liquid-tight metal protective hoses, made of galvanized cast steel with chrome-plated surface, inner sleeve made of polyamide, nominal size 2 inches or 63 mm, threaded connection NPT 2 inches, protection class IP67
Sales unit: 5 pieces
Lieske Part No.: 297254

Straight metal screw connection, for liquid-tight metal protective hoses, made of galvanized cast steel with chrome-plated surface, inner sleeve made of polyamide, nominal size 1 1/2 inch or 50 mm, threaded connection NPT 1 1/2 inch, protection class IP67
Sales unit: 10 pieces
Lieske Part No.: 1581170

45° - angled metal screw connection, for liquid-tight metal protective hoses, made of galvanized cast steel with chrome-plated surface, inner sleeve made of polyamide, nominal size 1 1/2 inch or 50 mm, thread connection NPT 1 1/2 inch, protection class
Sales unit: 2 pieces
Lieske Part No.: 1581168

90° - angled metal screw connection, for liquid-tight metal protective hoses, made of galvanized cast steel with chrome-plated surface, inner sleeve made of polyamide, nominal size 1 1/2 inch or 50 mm, thread connection NPT 1 1/2 inch, protection class
Sales unit: 2 pieces
Lieske Part No.: 1581121

TYPEA Liquid-tight and flexible plastic protective hose with smooth inner and outer surface, construction 2-layer PVC with nylon braid, color orange, nominal size 1/2 inch or 20 mm, protection class IP 66, length 61 m. 1 roll = 200 Ft = 61
Lieske Part No.: 300620

Der braune Ty-Rap Stahlnasenkabelbinder aus Polyamid 6.6 ist in mehreren Längen und Breiten und unterschiedlichen Zugfestigkeiten erhältlich. Diese Baureihe ist hauptsächlich für Anwendungen im Innenbereich geeignet. Die korrosionsbeständige, antimagnetische Stahlnase aus dem Edelstahl Typ 316 im Kabelbinderkopf garantiert den stärksten und sichersten Halt, der am Markt zu finden ist. Der leistungsstarke und zuverlässige Ty-Rap kann unter widrigsten Bedingungen wie unter Vibrationen, Hitze oder Kälte eingesetzt werden. Die abgerundeten Kanten und Konturen des Kopfes und des Binders sorgen für eine anwenderfreundliche Handhabung und verhindern, dass die Isolation der Kabel und Leitungen durch scharfe Kanten oder Verzahnungen beschädigt werden. Zudem reduziert der glatte Körper ohne Rasterzähne oder Rillen die Zahl überbeanspruchter Stellen. Die leichte Noppung auf der Innenseite des Bandes gewährleistet einen festen Sitz des Binders auf dem Kabelbündel. Eine große Auswahl an Zubehör ergänzt das Sortiment.
Sales unit: 1000 pieces
Lieske Part No.: 1278168

The Ty-Rap steel nose cable tie made of fluoropolymer ECTFE is characterized by very low smoke development in the event of a fire and is therefore suitable for applications where reduced smoke development is required, such as in security areas and assembly areas. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold available on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The slight nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 1311946

The natural-colored Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 100 pieces
Lieske Part No.: 1583811

The black UV-resistant Ty-Rap steel nose cable tie for the railway industry made of polyamide 6.6 (certified according to the latest standards: NFF 16-101/102 and EN 45545-2) is available in several lengths and widths and different tensile strengths. This series is especially suitable for outdoor installations. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used in the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 323654

The purple Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used in the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 1314073

The gray Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used in the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 1317230

The black UV-resistant Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is especially suitable for outdoor installations. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 1317229

The orange Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 1314075

The white Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used in the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 646792

The natural-colored Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 1317228

Der rote Ty-Rap Stahlnasenkabelbinder aus Polyamid 6.6 ist in mehreren Längen und Breiten und unterschiedlichen Zugfestigkeiten erhältlich. Diese Baureihe ist hauptsächlich für Anwendungen im Innenbereich geeignet. Die korrosionsbeständige, antimagnetische Stahlnase aus dem Edelstahl Typ 316 im Kabelbinderkopf garantiert den stärksten und sichersten Halt, der am Markt zu finden ist. Der leistungsstarke und zuverlässige Ty-Rap kann unter widrigsten Bedingungen wie unter Vibrationen, Hitze oder Kälte eingesetzt werden. Die abgerundeten Kanten und Konturen des Kopfes und des Binders sorgen für eine anwenderfreundliche Handhabung und verhindern, dass die Isolation der Kabel und Leitungen durch scharfe Kanten oder Verzahnungen beschädigt werden. Zudem reduziert der glatte Körper ohne Rasterzähne oder Rillen die Zahl überbeanspruchter Stellen. Die leichte Noppung auf der Innenseite des Bandes gewährleistet einen festen Sitz des Binders auf dem Kabelbündel. Eine große Auswahl an Zubehör ergänzt das Sortiment.
Sales unit: 1000 pieces
Lieske Part No.: 636477

The green Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 466840

The gray Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used in the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 1314076

The yellow Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used in the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 1313481

The orange Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 928714

The purple Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used in the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 1000 pieces
Lieske Part No.: 928789

The Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths and 10 different colors. This series is especially suitable for outdoor installations. The cable tie is packaged in recyclable plastic bags with Euro holes and contains 2% carbon for military specifications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used in the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 100 pieces
Lieske Part No.: 300110

Der weiße Ty-Rap Stahlnasenkabelbinder aus Polyamid 6.6 ist in mehreren Längen und Breiten und unterschiedlichen Zugfestigkeiten erhältlich. Diese Baureihe ist hauptsächlich für Anwendungen im Innenbereich geeignet. Die korrosionsbeständige, antimagnetische Stahlnase aus dem Edelstahl Typ 316 im Kabelbinderkopf garantiert den stärksten und sichersten Halt, der am Markt zu finden ist. Der leistungsstarke und zuverlässige Ty-Rap kann unter widrigsten Bedingungen wie unter Vibrationen, Hitze oder Kälte eingesetzt werden. Die abgerundeten Kanten und Konturen des Kopfes und des Binders sorgen für eine anwenderfreundliche Handhabung und verhindern, dass die Isolation der Kabel und Leitungen durch scharfe Kanten oder Verzahnungen beschädigt werden. Zudem reduziert der glatte Körper ohne Rasterzähne oder Rillen die Zahl überbeanspruchter Stellen. Die leichte Noppung auf der Innenseite des Bandes gewährleistet einen festen Sitz des Binders auf dem Kabelbündel. Eine große Auswahl an Zubehör ergänzt das Sortiment.
Sales unit: 1000 pieces
Lieske Part No.: 702192

The colored Ty-Rap steel nose cable tie made of polyamide 6.6 is available in many different colors, several lengths and widths and different tensile strengths. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 50 pieces
Lieske Part No.: 1311289

The black UV-resistant Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is especially suitable for outdoor installations. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 50 pieces
Lieske Part No.: 1317162

Der schwarz UV-beständige Ty-Rap Stahlnasenkabelbinder für die Bahnindustrie aus Polyamid 6.6 (zertifiziert nach den aktuellsten Normen: NFF 16-101/102 und EN 45545-2) ist in mehreren Längen und Breiten und unterschiedlichen Zugfestigkeiten erhältlich. Diese Baureihe ist speziell für Installationen im Außenbereich geeignet. Die korrosionsbeständige, antimagnetische Stahlnase aus dem Edelstahl Typ 316 im Kabelbinderkopf garantiert den stärksten und sichersten Halt, der am Markt zu finden ist. Der leistungsstarke und zuverlässige Ty-Rap kann unter widrigsten Bedingungen wie unter Vibrationen, Hitze oder Kälte eingesetzt werden. Die abgerundeten Kanten und Konturen des Kopfes und des Binders sorgen für eine anwenderfreundliche Handhabung und verhindern, dass die Isolation der Kabel und Leitungen durch scharfe Kanten oder Verzahnungen beschädigt werden. Zudem reduziert der glatte Körper ohne Rasterzähne oder Rillen die Zahl überbeanspruchter Stellen. Die leichte Noppung auf der Innenseite des Bandes gewährleistet einen festen Sitz des Binders auf dem Kabelbündel. Eine große Auswahl an Zubehör ergänzt das Sortiment.
Sales unit: 500 pieces
Lieske Part No.: 1283892

The natural-colored Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 500 pieces
Lieske Part No.: 300046

The yellow Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used in the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 500 pieces
Lieske Part No.: 1314077

The green Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 500 pieces
Lieske Part No.: 1314078

The blue Ty-Rap steel nose cable tie made of polyamide 6.6 is available in several lengths and widths and different tensile strengths. This series is mainly suitable for indoor applications. The corrosion-resistant, anti-magnetic steel nose made of type 316 stainless steel in the cable tie head guarantees the strongest and most secure hold that can be found on the market. The powerful and reliable Ty-Rap can be used under the most adverse conditions such as vibration, heat or cold. The rounded edges and contours of the head and the tie ensure user-friendly handling and prevent the insulation of the cables and lines from being damaged by sharp edges or serrations. In addition, the smooth body without ratchet teeth or grooves reduces the number of overstressed areas. The light nubs on the inside of the band ensure that the tie sits firmly on the cable bundle. A large selection of accessories complements the range.
Sales unit: 500 pieces
Lieske Part No.: 1314079