INTELLINET 561679
PoE-Powered 8-Port PoE+ Gigabit Switch with PoE passthrough

One PoE++ IEEE 802.3bt (4PPoE) PD PoE port with 90W input power, seven PSE PoE ports, PoE power budget up to 85W, IEEE 802.3at/af compliant
PoE passthrough technology for added value and longer range:
This The 8-Port Gigabit Switch from Intellinet Network Solutions has PoE passthrough technology as its most important feature, which means it can also be used as a PoE extender. It takes power and data from a PoE switch or injector and extends this connection to seven output ports by an additional 100 m. It is powered exclusively via PoE, which makes you completely independent of existing sockets when placing it and therefore saves a lot of money Wiring saves.
Power over Ethernet 802.3at:
This switch supports the IEEE 802.3at protocol, delivering up to 30 watts of power per port*. IEEE802.3af or IEEE802.3at compliant devices connected to the switch do not require additional power, saving significant cost and time on power line routing and eliminating a lot of cable clutter and adapters in exposed locations such as walls and ceilings. Any combination of PoE and non-PoE devices is supported and your equipment is well protected thanks to protection against short circuits, overloads and overvoltages. For devices that do not support the 802.3at/af standard (older access points or network cameras), we recommend using an Intellinet PoE/PoE+ splitter.
Gigabit speed instead of a bottleneck:
Equipped with seven auto-sensing 10/100/1000 Mbit/s RJ45 Gigabit Ethernet ports, this switch offers huge performance for computers, servers and other network devices.
Green Ethernet technology:
Network switches rarely use all ports at the same time. If a PC, notebook, printer or other device on the network is turned off, a normal switch continues to use the same amount of power as if those devices were turned on. Thanks to energy-efficient IEEE 802.3az technology, this switch automatically detects the status of all connected devices and reduces power consumption of unused ports. It can also adjust its own power consumption based on the length of the connected network cable. This combination saves you energy and therefore money.
* The total PoE budget of this switch is 85 watts when used at 90W input power from an Ultra PoE IEEE 802.3bt switch or injector. The maximum usage on one port is 30 watts. - Supports up to 90W input power from a PoE injector or PoE switch

• Power and data connection for up to seven PoE network devices
• Doubles the connection range between PoE source and device from 100m to 200m
• PoE power budget of 85 watts with 90 W input power via IEEE 802.3bt connection
• PoE power budget of 20 watts with IEEE 802.3at connection and 10 watts with IEEE 802.3af connection
• Powered only via PoE
• Saves time and installation costs the transmission of data and power via the existing network cables
• IEEE 802.3at/af-compliant RJ45 PoE/PoE+ outputs
• Output power up to 30 watts per port
• Grounding point to protect against external electrical voltage peaks
• Supports IEEE 802.3at- and IEEE 802.3af- Compliant PoE devices (Wireless Access Points, VoIP phones, IP cameras)
• Supports IEEE 802.3at/af detection as well as protection against short circuit, overload and overvoltage
• 10/100/1000 auto-sensing ports automatically detect the optimal network speed
• 16 Gbit/s Switch Fabric
• Low-power Green Ethernet technology disables unused ports and adjusts power level according to cable length
• All RJ45 ports support Auto-MDIX (Auto Uplink)
• Supports 2,000 MAC addresses with auto-learning and auto -Aging
• Store-and-forward architecture
• Supports IEEE 802.3x flow control at full duplex and backpressure at half duplex
• LEDs for power, link/activity and PoE
• Fan-free design for quiet operation
• Fully NDAA compliant
• 3 year warranty standards
• IEEE 802.3i (10Base-T Ethernet)
• IEEE 802.3u (100Base-TX Fast Ethernet)
• IEEE 802.3ab (Twisted-pair Gigabit Ethernet)
• IEEE 802.3af (Power over Ethernet 802.3at Type 1)
• IEEE 802.3at (Power over Ethernet 802.3at Type 2)
• IEEE 802.3bt (Ultra PoE++/4PPoE Power over Ethernet)
• IEEE 802.3az (Energy Efficient Ethernet [EEE])
• IEEE 802.3x (Flow Control for full duplex mode)
General:

• Supported media
• 10Base- T Cat5e UTP/STP RJ45, 8-pin.
• 100Base-TX Cat5e UTP/STP RJ45, 8-pin.
• 1000Base-T Cat5e UTP/STP RJ45, 8-pin.
• Packet Filter/Forwarding Rate:
• 1,488,000 pps (1,000 Mbit/s)
• 148,800 pps (100 Mbit/s)
• 14,880 pps (10 Mbit/s)
• MAC address table: 2,000 entries
• Backplane speed: 16 Gbit/s
• Store -and-forward architecture
• Certificates: FCC Class B, CE, RoHS
LEDs

• PoE
• Power
• Connection/Activity
Pin assignment RJ45 input port

• Pin 1: DC (-)
• Pin 2: DC (-)
• Pin 3: DC (+)
• Pin 4: DC (+)
• Pin 5: DC (+)
• Pin 6: DC (+)
• Pin 7: DC (-)
• Pin 8: DC (-)
Pin assignment RJ45 output ports

• Pin 1: DC (-)
• Pin 2: DC (-)
• Pin 3: DC (+)
• Pin 6: DC (+)
power

• Via PD port (Port 8)
• Input: IEEE802.3af/at/bt compliant
• PoE power budget: 85 watts (max.)
• Input: 48 - 57 V; up to 90 watts
• output: 44 - 57 V; up to 30 watts per port
Environmental conditions

• Metal housing
• Dimensions: 104 x 240 x 29 mm
• Weight: 660 g
• Operating temperature 0 - 40?
• Storage temperature: -20 - 70°C
• Operating humidity: 10 - 90% RH, not condensing
• Humidity during storage: 5 - 95% RH, non-condensing
Scope of delivery:

• 8-port PoE+ Gigabit switch with PoE passthrough
• Quick guide Color: Black Product dimensions: 104 (L) x 240 (W) x 29 (H) [mm ]