Wall Plugs in Fixing hardware

Die fischer PowerFast II FPF II CTP BC ist eine galvanisch verzinkte, blau passivierte Schraube mit Teilgewinde und Innenstern-Aufnahme. Der Senkkopf ermöglicht die oberflächenbündige Montage im Holz. Die Ausführung mit Teilgewinde ermöglicht das feste Aneinanderziehen von Holzelementen. Die Schraube eignet sich für Befestigungen von tragenden Bauteilen in beschichtetem Holz, Hartholz, Weichholz und Holzverbindungen. Verkaufseinheit: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 540746

Die fischer PowerFast II FPF II CTF BC ist eine galvanisch verzinkte, blau passivierte Schraube mit Vollgewinde und Innenstern-Aufnahme. Der Senkkopf ermöglicht die oberflächenbündige Montage im Holz. Das durchgängige Gewinde über die gesamte Schraubenlänge sorgt für eine optimale Kraftübertragung. Die Schraube eignet sich ideal für die Befestigung bei allgemeinen Holzverbindungen, von Beplankungen, Sockelleisten sowie Tür- und Metallbeschlägen. Verkaufseinheit: 50 ST.
Sales unit: 50 pieces
Lieske Part No.: 540602

Die fischer PowerFast II FPF II CTF BC ist eine galvanisch verzinkte, blau passivierte Schraube mit Vollgewinde und Innenstern-Aufnahme. Der Senkkopf ermöglicht die oberflächenbündige Montage im Holz. Das durchgängige Gewinde über die gesamte Schraubenlänge sorgt für eine optimale Kraftübertragung. Die Schraube eignet sich ideal für die Befestigung bei allgemeinen Holzverbindungen, von Beplankungen, Sockelleisten sowie Tür- und Metallbeschlägen. Verkaufseinheit: 50 ST.
Sales unit: 50 pieces
Lieske Part No.: 540585

For many materials such as concrete, bricks and wood. Can be combined with cable ties up to 9 mm wide. Simply hammer into hole (7-8 mm). LOK01B is intended for soft masonry and 6 mm holes. LOK05 with spacing to guide bundles at a distance from the masonry. The LOK wall plug is used in combination with a cable tie for the efficient laying and fastening of cables and lines in buildings.
Sales unit: 100 pieces
Lieske Part No.: 311572

Kippdübel, mit Gewindestange, inkl. 1 U-Scheibe nach DIN EN ISO 7089, 1 Flachscheibe und 2 Sechskantmuttern nach DIN EN ISO 4032, für den Einsatz an Hohlraumdecken und -wänden. Gewinde : M 5 Gewindelänge : 100 mm Gesamtlänge : 100 mm Bohrloch-Ø : 13 mm Erforderliche Hohlraumtiefe : 70 mm max. Plattendicke : 40 mm Tragfähigkeit zul. F : 0,16 kN (die Tragfähigkeitsangaben beinhalten eine 5-fache Sicherheit und gelten nur bei ausreichender Tragfähigkeit des Untergrundes) Werkstoff : Stahl, galvanisch verzinkt Verkaufseinheit: 1 ST.
Lieske Part No.: 1241174

Kippdübel, mit Deckenhaken, inkl. 2 U-Scheiben nach DIN EN ISO 7089 und 2 Sechskantmuttern nach DIN EN ISO 4035, für den Einsatz an Hohlraumdecken und -wänden. Gewinde : M 5 Gewindelänge : 80 mm Gesamtlänge : 130 mm Bohrloch-Ø : 15 mm Erforderliche Hohlraumtiefe : 70 mm max. Plattendicke : 50 mm Tragfähigkeit zul. F : 0,6 kN (die Tragfähigkeitsangaben beinhalten eine 5-fache Sicherheit und gelten nur bei ausreichender Tragfähigkeit des Untergrundes) Werkstoff : Stahl, galvanisch verzinkt Werkstoff Achse : Messing Verkaufseinheit: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 1241238

Toggle anchor with ceiling hook, galvanized according to DIN EN ISO 2081, blue passivated, the axle is made of brass, for use on hollow ceilings and walls, including 1 flat washer and 1 hexagon nut according to DIN EN ISO 4035. The load values include a safety factor of 5. The load-bearing capacity information only applies if the substrate has sufficient load-bearing capacity. Threaded rod: M 5 Thread length: 70 mm Total length: 98 mm Borehole diameter: 15 mm Required cavity depth: 70 mm Max. panel thickness: 20 mm Load-bearing capacity F: 0.12 kN
Sales unit: 50 pieces
Lieske Part No.: 544996

NIEDAX - Make: 224 H toggle bolt with ceiling hook, galvanized to DIN 5 96
, blue passivated, for cavity walls and ceilings, including
washer according to DIN EN ISO 7 89 and
hexagon nut to DIN EN ISO 4 35 The load values ​​include a safety factor of 4 The carrying capacity apply only with adequate bearing capacity of the ground. Hakeninnendurchm. 2 mm threaded rod: M 6 Thread Length:
mm total length L:
32 mm Load capacity F: 25 kN hole diameter:
7 mm NIEDAX model no. 224 H Type: 224H item:
ST.
Sales unit: 25 pieces
Lieske Part No.: 946872

Push-through anchor with metric connection thread M 6, including galvanized flange nut. Permissible loads for centric tension, transverse load and diagonal tension at any angle as well as anchor characteristics and component dimensions for concrete strength classes = B 25 or C 20/25 and = B 55 or C 50/60. The entire approval notice no.: ETA-18/0541 must be observed when dimensioning! For outdoor areas we recommend push-through anchors made of stainless steel! For use in functional maintenance or for suspended ceilings with fire protection requirements (model pipe system guideline MLAR 2/2015) please note additional regulations! Area of application: The anchor can be used as a multiple fastening for anchoring light ceiling cladding and suspended ceilings in accordance with DIN 18168, as well as for statically comparable anchoring up to 1 kN/m² - also in the tensile zone generated by load stresses. When setting the push-through anchor, ensure that the effective anchoring depth is maintained. Compliance is ensured by adhering to the permissible thickness of the fixture (clamping range). Technical details Connecting thread: M 6 Total length L: 55 mm Nominal drilling diameter: 6 mm Clamping range t fix: = 10 mm Effective anchoring depth h ef: 30 mm Recommended torque: 4 Nm Wrench size: 10 Material: Steel, galvanized in accordance with DIN EN ISO 2081/4042, blue passivated Approval no.: ETA-18/0541 DoP NI001
Sales unit: 100 pieces
Lieske Part No.: 1337353

NIEDAX - Make: DAM 6X5
Through anchor, steel, galvanized to DIN 50961, passivated, including galvanized nut and galvanized washer. For use in the functional integrity please follow additional rules! Permissible loads for train-centric, cross and shear loading at any angle and anchor characteristics and dimensions for concrete strength> = B 25 and C 20 / 25th When calculating the
entire certification No.: ETA-06/0175 to note! For outdoor use, we recommend anchor made of stainless steel!

Dimensions:

permissible load of single anchors: 1.6 kN

Permissible bending moment M: 4 Nm
max. Torque when attaching the fixture with torque =
Key M (D): 4 Nm

Nominal drill hole diameter d (0) = 6 mm

Cutting diameter of <= 6,4 mm
Through hole in the subsequent
Component d (f) <= 7 mm

minimum hole depth h (0)> = 40 mm

minimum anchoring depth h (v)> = 30 mm
Center distance between the outer anchors of adjoining groups
or single anchors az> = 200 mm
Spacing of the outer anchor
to the component edge ar> = 100 mm

Minimum thickness d (a) = 80 mm

Total length l = 50 mm

Fixture thickness t fix <= 5 mm

Certificate No.:. ETA-06/0175

Scope: The anchor may as multiple fixing for the anchorage for suspended ceilings and suspended ceilings according to DIN 18168, as well as for static anchors similar to 1 kN / mý - used - even in the tension zone generated from load voltages.

NIEDAX model no. DAM 6x5

Type: DAM6x5
Item: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 253806

NIEDAX - Make: DAZ 10X10
stud anchor, steel, galvanized to DIN 50961, blue passivated, including galvanized galvanized washer and nut. For use in the functional integrity please follow additional rules! For outdoor use, we recommend anchor made &#8203;&#8203;of stainless steel!

Dimensions:

Diam.x max. Mat thickness: M 10 x 10 mm embedment depth: 60 mm Mounting Torque: 45 Nm Drill diameter: 10 mm Hole depth including mounting part thickness: 80mm Certificate No.:. ETA-00/0001 and ETA-05/0069 NIEDAX Model No. .: DAZ 10x10 Type: DAZ10X10 item: 50 ST.
Sales unit: 50 pieces
Lieske Part No.: 114924

NIEDAX - Make: DAZ 10X30
stud anchor, steel, galvanized to DIN 50961, blue passivated, including galvanized galvanized washer and nut. For use in the functional integrity please follow additional rules! For outdoor use, we recommend anchor made of stainless steel!

Dimensions:

Diam. x max.Mat thickness: M 10 x 30 mm embedment depth: 60 mm Mounting Torque: 45 Nm Drill diameter: 10 mm






Including drill hole depth
Assembly part thickness: 100 mm

Certificate No.:. ETA-00/0001 and ETA-05/0069

NIEDAX model no. DAZ 10x30 Type: DAZ10X30


Item: 100 ST.
Sales unit: 25 pieces
Lieske Part No.: 663291

Heavy-duty steel dowel, with fixed threaded rod, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The steel dowel has not been tested by the building authorities and can therefore only be used for minor fastenings! Dimensions (approx. dimensions) for thread: M 8 Nominal drilling diameter: 14 mm Dowel length L: 60 mm Total length L: 100 mm Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 1315752

Heavy-duty steel dowel, with fixed threaded rod, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The steel dowel has not been tested by the building authorities and can therefore only be used for secondary fastenings! Dimensions (approx. dimensions) for thread: M 12 Nominal drilling diameter: 20 mm Dowel length L: 80 mm Total length L: 120 mm Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 25 pieces
Lieske Part No.: 460380

Nail anchor. Anchor for use in concrete for multiple fastening. The nail anchor is placed in a drill hole and spread by applying the load. The nail anchor is suitable for push-through installation. To be installed by lightly hammering the nail head. Permissible loads for centric tension, transverse load and diagonal tension at any angle as well as anchor characteristics and component dimensions for concrete strength classes = B 25 or C 20/25 and = B 55 or C 50/60. The entire approval notice no. ETA-18/0541 must be observed when dimensioning! For outdoor areas we recommend nail anchors made of stainless steel! For use in functional maintenance or for suspended ceilings with fire protection requirements (model pipe system guideline MLAR 2/2015) please observe additional regulations! Area of application The anchor can be used as a multiple fastening for anchoring light ceiling coverings and suspended ceilings in accordance with DIN 18168, as well as for statically comparable anchoring up to 1 kN/m² - also in the tension zone generated by load stresses. Technical details Total length L: 65 mm Nominal bore diameter: 6 mm Clamping range t fix: = 30 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081/4042, blue passivated Approval no.: ETA-18/0541 DoP NI001
Sales unit: 100 pieces
Lieske Part No.: 265452

NIEDAX - Make: NA 6X5 nail anchor made &#8203;&#8203;of steel, galvanized to DIN 5 96
, passivated. For use in the functional integrity please follow additional rules!Permissible loads for train-centric, cross and shear loading at any angle and anchor characteristics and dimensions for concrete strength> = 25 B and C, 2/25 When assessing the entire certification No. is: ETA 6 /
75 to note! For outdoor use, we recommend anchor made of stainless steel!Dimensions: Permissible load of single anchors:
, 6 kN Permissible bending moment M: 4 Nm max. Torque when attaching the fixture with torques = t M (D) - Nm nominal drill hole diameter d () = 6 mm cutting diameter <= 6,4 mm hole in the subsequent component d (f) <= 7 mm minimum hole depth h ( )> = 4 mm minimum anchoring depth h (v)> = 3 mm spacing between outer anchors of adjoining groups or between single anchors az> = 2 mm spacing of the outer anchors the component edge ar> =:
mm minimum thickness d (a) = 8 mm total length l = 4 mm fixture thickness t fix <= 5 mm Certificate No.:. ETA 6 /
75 Scope: The anchor may as multiple fixing for the anchorage for suspended ceilings and suspended ceilings according to DIN
8
68, as well as for static anchors similar to
kN / mý - used - even in the tension zone generated from load voltages. For outdoor use, we recommend anchor made &#8203;&#8203;of stainless steel. NIEDAX model no. 6x5 NA Type: NA6x5 item:
ST.
Sales unit: 100 pieces
Lieske Part No.: 537737

NIEDAX - Make: SMU 10
Hexagonal nut to DIN EN ISO 4032 and washer according to DIN EN ISO 7089, galvanized to ISO 4042, blue passivated. For use in the functional integrity please follow additional rules!

for thread: M 10 NIEDAX model no. SMU 10 Type: SMU10




Quantity: 1 unit.
Sales unit: 50 pieces
Lieske Part No.: 241122

To increase the clamping height of cable clamps from 10 to 13 mm for larger cable cross-sections.
Sales unit: 50 pieces
Lieske Part No.: 930929

The dowel can be driven directly into the aerated concrete (gas concrete strength class G2). From strength class G4 onwards, a 5 mm or 6 mm hole should be pre-drilled.
Screw length: component thickness + 40 mm (6 mm) / 55 mm (8 mm)
Sales unit: 100 pieces
Lieske Part No.: 365697

Concrete anchors 9
/ DG flame resistant, gas for driving into concrete. Material glass fiber reinforced polyamide Style: 8 x 5 mm Type: 9
GD 8x5 Package: 5 ea.
Sales unit: 50 pieces
Lieske Part No.: 547459

Impact screw: tempered steel, galvanized, transparent passivated.
Sales unit: 100 pieces
Lieske Part No.: 972906

Also suitable as a cavity anchor, with a collar to prevent slipping. 3 attached fins absorb the torque.
Required minimum screw length = anchor length + component thickness + 1 x screw diameter.
The pull-out value applies to wood screws with the largest screw diameter in concrete of class B25.
Our safety value recommendation: 5 times
Sales unit: 100 pieces
Lieske Part No.: 1101170

Also suitable as a cavity anchor, with a collar to prevent slipping. 3 attached fins absorb the torque.
Required minimum screw length = anchor length + component thickness + 1 x screw diameter.
The pull-out value applies to wood screws with the largest screw diameter in concrete of class B25.
Our safety value recommendation: 5 times
Sales unit: 100 pieces
Lieske Part No.: 110118

Also suitable as a cavity anchor, with a collar to prevent slipping. 3 attached fins absorb the torque.
Required minimum screw length = anchor length + component thickness + 1 x screw diameter.
The pull-out value applies to wood screws with the largest screw diameter in concrete of class B25.
Our safety value recommendation: 5 times
Sales unit: 50 pieces
Lieske Part No.: 1101182

Also suitable as a cavity anchor, with a collar to prevent slipping. 3 attached fins absorb the torque.
Required minimum screw length = anchor length + component thickness + 1 x screw diameter.
The pull-out value applies to wood screws with the largest screw diameter in concrete of class B25.
Our safety value recommendation: 5 times
Sales unit: 25 pieces
Lieske Part No.: 1101183

Insulation dowel for universal, easy fastening in plastered thermal insulation composite systems. With self-tapping tip.
Sales unit: 10 pieces
Lieske Part No.: 1956264

Required minimum screw length = dowel length + component thickness + 1 x screw diameter.
Extraction force applies to wood screws with the largest screw diameter; required safety factors must be taken into account.
Sales unit: 100 pieces
Lieske Part No.: 1056455

With M6 thread.
Impact screw: tempered steel, galvanized, transparent passivated.
Sales unit: 100 pieces
Lieske Part No.: 402114

OBO-impact anchor 9
/ SD: Impact Sockets: tempered steel, galvanized, yellow chromated PA Polyamide, gray white RAL 9 2 Anchor length: 5 x 35 mm Type: 9
SD 5X35 Quantity:
ST.
Sales unit: 100 pieces
Lieske Part No.: 781811

Impact screw: steel, galvanized, transparent passivated.
Sales unit: 100 pieces
Lieske Part No.: 445535

Impact screw: steel, galvanized, transparent passivated.
Sales unit: 100 pieces
Lieske Part No.: 289243

OBO-impact anchor 910/SD: shock bolt: tempered steel, galv galvanized, yellow chromated PA Polyamide, RAL 9002 gray white anchor length: 8 x 50 mm Type: SD 8X55 910 item: 50 ST.
Sales unit: 50 pieces
Lieske Part No.: 555116

Impact dowel for Quick clamps type 2955.
Impact screw: tempered steel, galvanized, transparent passivated.
Sales unit: 100 pieces
Lieske Part No.: 436204

Steckdübel zur Montage in der Elektroinstallation. Geeignet für Beton, Kalksandstein, Vollziegel, Hohllochziegel und Porenbeton. Werkzeuglose Montage durch Eindrücken in Bohrloch an Wand oder Decke. Ohne Schrauben. Zur Installation von z. B. Leitungsführungskanälen oder Kennzeichungsschildern. Verkaufseinheit: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 1247293

Steckdübel zur Montage in der Elektroinstallation. Geeignet für Beton, Kalksandstein, Vollziegel, Hohllochziegel und Porenbeton. Werkzeuglose Montage durch Eindrücken in Bohrloch an Wand oder Decke. Ohne Schrauben. Mit M6-Gewinde zum Aufschrauben von z. B. Quick-Schellen. Verkaufseinheit: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 1247294

Steckdübel zur Montage in der Elektroinstallation. Geeignet für Beton, Kalksandstein, Vollziegel, Hohllochziegel und Porenbeton. Werkzeuglose Montage durch Eindrücken in Bohrloch an Wand oder Decke. Ohne Schrauben. Mit Kabelbinderaufnahme bis 4,8 mm Breite zur Befestigung von Kabeln und Rohren. Verkaufseinheit: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 1247295

Hardened steel, galvanized
with thread M6 x 8 mm.
Sales unit: 100 pieces
Lieske Part No.: 248049

Hardened steel, galvanized
with thread M6 x 8 mm.
Sales unit: 100 pieces
Lieske Part No.: 528533

Hardened steel, galvanized
with thread M6 x 8 mm.
Sales unit: 100 pieces
Lieske Part No.: 928783

Hardened steel, galvanized
with thread M6 x 8 mm.
Sales unit: 100 pieces
Lieske Part No.: 583335

Hardened steel, galvanized
with thread M6 x 8 mm.
Sales unit: 100 pieces
Lieske Part No.: 871189

Hardened steel, bright without thread.
Sales unit: 200 pieces
Lieske Part No.: 964219

Hardened steel, bright without thread.
Sales unit: 200 pieces
Lieske Part No.: 864905

Hardened steel, bright without thread.
Sales unit: 200 pieces
Lieske Part No.: 414751

. with wood screw shaft and thread M6
Sales unit: 100 pieces
Lieske Part No.: 125213

. with wood screw shaft and thread M6
Sales unit: 100 pieces
Lieske Part No.: 323040

. with wood screw shaft and thread M8
Sales unit: 100 pieces
Lieske Part No.: 878633

Serrated lock washer according to DIN 6798, form A.
Sales unit: 100 pieces
Lieske Part No.: 318803

Serrated lock washer according to DIN 6798, form A.
Sales unit: 100 pieces
Lieske Part No.: 315153

Serrated lock washer according to DIN 6798, form A.
Sales unit: 100 pieces
Lieske Part No.: 282614