Holzschraube, mit Tellerkopf und Torxantrieb. Zur Befestigung von Niedax Kabeltragsystemen mit integriertem Funktionserhalt an tragenden Holzbauteilen nach DIN EN 1995-1-2. Europäische techn. Bewertung: Zulassungs.Nr. ETA-19/0553. Zur Verwendung im Funktionserhalt bitte Zusatzvorschriften beachten! Gew.-Aussen-Ø : 6 mm Länge : 60 mm Gewindelänge : 56 mm Torxantrieb : T30 Kopf-Ø : 14 mm Empf. Anzugsmoment : 9,5 Nm Bohrungs-Ø Nadelholz : 4,0 mm Bohrungs-Ø Buche, Eiche, Esche : 4,0 mm Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert
Sales unit: 100 pieces
Lieske Part No.: 705772

Schraubanker mit Flachrundkopf und Torxantrieb T30. Zur Verwendung im Funktionserhalt bzw. für Unterdecken mit brandschutztechnischen Anforderungen (Muster-Leitungsanlagen-Richtlinie MLAR 2/2015) bitte Zusatzvorschriften beachten! Anwendung : Anzahl und Anordnung der Schraubanker sind der Ausführungsplanung bzw. dem statischen Nachweis zu entnehmen und einzuhalten. Einbau und Montage gemäß Europäisch Technischer Bewertung ETA-15/0784 bzw. Montageanleitung im gerissenen und ungerissenen Beton C20/25 bis C50/60. Bei der Bemessung ist der gesamte Zulassungsbescheid ETA-15/0784 zu beachten. Zur Verwendung in Mauerwerk gemäß Europäisch Technischer Bewertung ETA-20/0132. Für Kalksandstein KS, Kalksandlochstein KSL und Vollziegel MZ liegt ein Brandschutzgutachten für den Funktionserhalt vor. Verwendung in trockenen Innenräumen. Setzen des Schraubankers mit Tangential Schlagschrauber oder von Hand. Verwendung für : Sammelhalter SHS... Technische Angaben Ø : 6 mm Länge L : 35 mm Kopf-Ø : 11 mm Bohrnenn-Ø : 5 mm Klemmbereich t fix : 1 mm empfohlenes Drehmoment : 10 Nm Torxantrieb : T30 Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert Zulassungs-Nr. : ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 691746

Screw anchor with flat round head and Torx drive T30. For use in functional maintenance or for suspended ceilings with fire protection requirements (model pipe system guideline MLAR 2/2015), please observe additional regulations! Application: The number and arrangement of the screw anchors can be found in the implementation plan or the static proof and must be observed. Installation and assembly in accordance with European Technical Assessment ETA-15/0784 or assembly instructions in cracked and non-cracked concrete C20/25 to C50/60. The entire approval notice ETA-15/0784 must be observed when dimensioning. For use in masonry, see general type approval Z-21.1-2103. A fire protection report for functional maintenance is available for KS sand-lime brick, KSL perforated sand-lime brick and MZ solid brick. Use in dry interior rooms. Set the screw anchor with a tangential impact wrench or by hand. Use for: Collective holder SHS... Technical details Ø: 6 mm Length L: 50 mm Head Ø: 11 mm Nominal bore Ø: 5 mm Clamping range t fix: 5 mm Recommended torque: 10 Nm Torx drive: T30 Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated Approval no.: ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 1348981

Schraubanker mit Sechskantkopf und metrischem Anschlußgewinde M 6. Zur Verwendung im Funktionserhalt bzw. für Unterdecken mit brandschutztechnischen Anforderungen (Muster-Leitungsanlagen-Richtlinie MLAR 2/2015) bitte Zusatzvorschriften beachten! Anwendung : Anzahl und Anordnung der Schraubanker sind der Ausführungsplanung bzw. dem statischen Nachweis zu entnehmen und einzuhalten. Einbau und Montage gemäß Europäisch Technischer Bewertung ETA-15/0784 bzw. Montageanleitung im gerissenen und ungerissenen Beton C20/25 bis C50/60. Bei der Bemessung ist der gesamte Zulassungsbescheid ETA-15/0784 zu beachten. Zur Verwendung in Mauerwerk gemäß Europäisch Technischer Bewertung ETA-20/0132. Für Kalksandstein KS, Kalksandlochstein KSL und Vollziegel MZ liegt ein Brandschutzgutachten für den Funktionserhalt vor. Verwendung in trockenen Innenräumen. Setzen des Schraubankers mit Tangential Schlagschrauber oder von Hand. Verwendung für : Schraubabstandschellen SAS... Rohr- und Kabelabstandschellen 85... G Technische Angaben Ø : 6 mm Gesamtlänge L : 55 mm Bohrnenn-Ø : 5 mm Anschlußgewinde : M 6 empfohlenes Drehmoment : 10 Nm Schlüsselweite : SW 10 Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert Zulassungs-Nr. : ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 691747

Schraubanker mit großem Flachrundkopf und Torxantrieb T30. Zur Verwendung im Funktionserhalt bzw. für Unterdecken mit brandschutztechnischen Anforderungen (Muster-Leitungsanlagen-Richtlinie MLAR 2/2015) bitte Zusatzvorschriften beachten! Anwendung : Anzahl und Anordnung der Schraubanker sind der Ausführungsplanung bzw. dem statischen Nachweis zu entnehmen und einzuhalten. Einbau und Montage gemäß Europäisch Technischer Bewertung ETA-15/0784 bzw. Montageanleitung im gerissenen und ungerissenen Beton C20/25 bis C50/60. Bei der Bemessung ist der gesamte Zulassungsbescheid ETA-15/0784 zu beachten. Zur Verwendung in Mauerwerk gemäß Europäisch Technischer Bewertung ETA-20/0132. Für Kalksandstein KS, Kalksandlochstein KSL und Vollziegel MZ liegt ein Brandschutzgutachten für den Funktionserhalt vor. Verwendung in trockenen Innenräumen. Setzen des Schraubankers mit Tangential Schlagschrauber oder von Hand. Verwendung für : Ankerschienen = 18 mm Schlitzweite Technische Angaben Ø : 7,5 mm Länge L : 40 mm Kopf-Ø : 17 mm Bohrnenn-Ø : 6 mm Klemmbereich t fix : 5 mm empfohlenes Drehmoment : 20 Nm Torxantrieb : T30 Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert Zulassungs-Nr. : ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 691744

Schraubanker mit großem Flachrundkopf und Torxantrieb T30. Zur Verwendung im Funktionserhalt bzw. für Unterdecken mit brandschutztechnischen Anforderungen (Muster-Leitungsanlagen-Richtlinie MLAR 2/2015) bitte Zusatzvorschriften beachten! Anwendung : Anzahl und Anordnung der Schraubanker sind der Ausführungsplanung bzw. dem statischen Nachweis zu entnehmen und einzuhalten. Einbau und Montage gemäß Europäisch Technischer Bewertung ETA-15/0784 bzw. Montageanleitung im gerissenen und ungerissenen Beton C20/25 bis C50/60. Bei der Bemessung ist der gesamte Zulassungsbescheid ETA-15/0784 zu beachten. Zur Verwendung in Mauerwerk gemäß Europäisch Technischer Bewertung ETA-20/0132. Für Kalksandstein KS, Kalksandlochstein KSL und Vollziegel MZ liegt ein Brandschutzgutachten für den Funktionserhalt vor. Verwendung in trockenen Innenräumen. Setzen des Schraubankers mit Tangential Schlagschrauber oder von Hand. Verwendung für : Ankerschienen = 18 mm Schlitzweite Technische Angaben Ø : 7,5 mm Länge L : 50 mm Kopf-Ø : 17 mm Bohrnenn-Ø : 6 mm Klemmbereich t fix : 15 mm empfohlenes Drehmoment : 20 Nm Torxantrieb : T30 Werkstoff : Stahl, galvanisch verzinkt nach DIN EN ISO 19598/4042, blaupassiviert Zulassungs-Nr. : ETA-15/0784
Sales unit: 100 pieces
Lieske Part No.: 691745

NIEDAX - Make: RCM
Ring bolt M
, forged, for the attachment of node chains, galvanized to DIN 5 96
, blue passivated, including two hex nuts. Breaking load: 2
kN Thread: M
opening size of ring: mm NIEDAX model no. RCM type: RCM




ST.
Sales unit: 50 pieces
Lieske Part No.: 526968

NIEDAX - Make: RCM 6 M 6 screw ring, forged, for the attachment of node chains, galvanized to DIN 5 96
, blue passivated, including two hex nuts. Breaking load: 7,3 kN Thread: M 6 opening size of ring: 6.5 mm NIEDAX model no. 6 RCM type: RCM6 item:
ST.
Sales unit: 50 pieces
Lieske Part No.: 843536

NIEDAX - Make: RCM 8 M 8 screw ring, forged, for the attachment of node chains, galvanized to DIN 5 96
, Blue passivated, including two hex nuts. Breaking load:
4.6 kN Thread: M 8 opening size of ring: 8.5 mm NIEDAX model no. RCM 8 Type: RCM8 item:
ST.
Sales unit: 50 pieces
Lieske Part No.: 921499

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 20 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 231309

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 25 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 532836

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 35 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 100 pieces
Lieske Part No.: 1426291

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 40 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 231323

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 10 Screw length: 50 mm Strength class: 8.8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 1315777

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 12 Screw length: 100 mm Strength class: 8.8 Screw tightening torque: 84 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 338376

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 12 Screw length: 120 mm Strength class: 8.8 Screw tightening torque: 84 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 231298

Hexagon head screw with slot similar to DIN EN ISO 4018, head with slot according to DIN 962. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 8 Screw length: 12 mm Strength class: 4.6 Screw tightening torque: 9.1 Nm Wrench size: SW 11 Material: Steel, galvanized according to DIN EN ISO 4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 537581

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 8 Screw length: 25 mm Strength class: 8.8 Screw tightening torque: 24.6 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 100 pieces
Lieske Part No.: 1426290

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 8 Screw length: 30 mm Strength class: 70 Screw tightening torque: 16 Nm Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 100 pieces
Lieske Part No.: 467986

Hexagon head screw according to DIN EN ISO 4017. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads via friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! Dimensions (approx. dimensions) Thread: M 8 Screw length: 40 mm Strength class: 70 Screw tightening torque: 16 Nm Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 100 pieces
Lieske Part No.: 1327254

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) Thread: M 10 Screw length: 25 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 705629

Hexagon screw according to DIN EN ISO 4017, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 10 Screw length: 30 mm Screw strength class: 70 Nut strength class: 70 Max. screw tightening torque: 30 Nm Material: Stainless steel, material no. 1.4404, AISI 316L
Sales unit: 100 pieces
Lieske Part No.: 163108

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 10 Screw length: 40 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 329313

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 10 Screw length: 50 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 281317

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) Thread: M 10 Screw length: 70 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 729351

Hexagon screw according to DIN EN ISO 4017, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 12 Screw length: 50 mm Screw strength class: 10.9 Nut strength class: 10 Screw tightening torque: 123 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 20 pieces
Lieske Part No.: 169269

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 12 Screw length: 50 mm Screw strength class: 10.9 Nut strength class: 10 Screw tightening torque: 123 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 20 pieces
Lieske Part No.: 134554

Hexagon screw according to DIN EN ISO 4017, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 12 Screw length: 70 mm Screw strength class: 10.9 Nut strength class: 10 Screw tightening torque: 123 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 20 pieces
Lieske Part No.: 169273

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) Thread: M 12 Screw length: 70 mm Screw strength class: 10.9 Nut strength class: 10 Screw tightening torque: 123 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 20 pieces
Lieske Part No.: 784993

Hexagon screw according to DIN EN ISO 4017, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 16 Screw length: 40 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 206 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 20 pieces
Lieske Part No.: 774576

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class is to be used to determine the torque. Dimensions (approx. dimensions) Thread: M 8 Screw length: 16 mm Screw strength class: 70 Nut strength class: 70 Screw tightening torque: 16 Nm Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 50 pieces
Lieske Part No.: 230404

Hexagon screw according to DIN EN ISO 4017, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class is to be used to determine the torque. Dimensions (approx. dimensions) Thread: M 8 Screw length: 16 mm Screw strength class: 70 Nut strength class: 70 Screw tightening torque: 16 Nm Material: stainless steel, material no. 1.4571
Sales unit: 50 pieces
Lieske Part No.: 774345

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class is to be used to determine the torque. Dimensions (approx. dimensions) Thread: M 8 Screw length: 16 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 24.6 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 10 pieces
Lieske Part No.: 234475

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 8 Screw length: 16 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 24.6 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 10 pieces
Lieske Part No.: 202613

Hexagon nut according to DIN EN ISO 4032, galvanized according to DIN EN ISO 4042, blue passivated. Thread: M10 Strength class: 8 Wrench size: SW 17 / SW 16
Sales unit: 100 pieces
Lieske Part No.: 409222

E-clips, turnbuckle, with hook and eyelet, for tightening the rope suspension. Dimensions (approx. dimensions) Hook and eyelet thread: M 6 Eyelet diameter: 10 mm Clamping range A: 155 - 245 mm Material: Stainless steel, material no. 1.4401, 1.4404
Sales unit: 10 pieces
Lieske Part No.: 537594

Beam clamp, pre-assembled, for mounting on beam flanges in accordance with DIN 1025 with a minimum dimension of 8 - 20 mm and a max. 14% inclination or parallel flanges with a flange thickness of 8 - 20 mm, for vertical suspensions using a threaded rod, pre-assembly of the beam clamp with the threaded rod before assembly is possible. The beam clamp may only be loaded perpendicular to the beam! for threaded rod: = M 8 Dimensions (approx. dimensions) Height H: 61 mm Width B: 17.5 mm Length L: 112 mm Beam flange thickness t: 8 - 20 mm Vertical nominal load F: 2.0 kN Material: Steel, strip galvanized in accordance with DIN EN 10346 Niedax model no.: TKM 1
Sales unit: 25 pieces
Lieske Part No.: 1327253

Beam clamp, pre-assembled, for mounting on beam flanges in accordance with DIN 1025 with a minimum dimension of 8 - 20 mm and a max. 14% inclination or parallel flanges with a flange thickness of 8 - 20 mm, for vertical suspensions using a threaded rod, pre-assembly of the beam clamp with the threaded rod before assembly is possible. The beam clamp may only be loaded perpendicular to the beam! for threaded rod: = M 10 Dimensions (approx. dimensions) Height H: 61 mm Width B: 19.5 mm Length L: 112 mm Beam flange thickness t: 8 - 20 mm Vertical nominal load F: 3.6 kN Material: Steel, strip galvanized in accordance with DIN EN 10346 Niedax model no.: TKM 2
Sales unit: 25 pieces
Lieske Part No.: 1327251

Beam clamp, pre-assembled, for mounting on beam flanges in accordance with DIN 1025 with a minimum dimension of 8 - 20 mm and a max. 14% inclination or parallel flanges with a flange thickness of 8 - 20 mm, for vertical suspensions using a threaded rod, pre-assembly of the beam clamp with the threaded rod before assembly is possible. The beam clamp may only be loaded perpendicular to the beam! for threaded rod: = M 12 Dimensions (approx. dimensions) Height H: 61 mm Width B: 21.5 mm Length L: 112 mm Beam flange thickness t: 8 - 20 mm Vertical nominal load F: 5 kN Material: Steel, strip galvanized in accordance with DIN EN 10346 Niedax model no.: TKM 3
Sales unit: 25 pieces
Lieske Part No.: 1327252

Body washer according to DIN EN ISO 7093-1, for covering larger mounting holes, for screws with M 12 thread. Dimensions (approx. dimensions) Inner Ø: 13 mm Outer Ø B: 37 mm Thickness t: 3 mm Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 100 pieces
Lieske Part No.: 564593

Body washer according to DIN EN ISO 7093-1, for covering larger mounting holes, for screws with M 12 thread. Dimensions (approx. dimensions) Inner Ø: 13 mm Outer Ø B: 37 mm Thickness t: 3 mm Material: Steel, galvanized according to DIN EN ISO 4042/2081, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 564598

Body washer according to DIN EN ISO 7093-1, for covering larger mounting holes, for screws with M 6 thread. Dimensions (approx. dimensions) Inner Ø: 6.4 mm Outer Ø B: 18 mm Thickness t: 1.6 mm Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 100 pieces
Lieske Part No.: 375131

Body washer according to DIN EN ISO 7093-1, for covering larger mounting holes, for screws with M 8 thread. Dimensions (approx. dimensions) Inner Ø: 8.4 mm Outer Ø B: 24 mm Thickness t: 2 mm Material: Steel, hot-dip galvanized according to DIN EN ISO 1461
Sales unit: 100 pieces
Lieske Part No.: 163112

NIEDAX - Make: U.S. M10
washer, steel according to DIN EN ISO 7089, DIN 50961 zinc plated, blue passivated, for screws with thread M 10 NIEDAX Model No.: U.S. M10. Type: USM10




Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 137426

Washer according to DIN EN ISO 7089, for screws with thread M 12. Dimensions (approx. dimensions) Inner Ø: 13 mm Outer Ø: 24 mm Thickness t: 2.5 mm Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 369778

Washer according to DIN EN ISO 7089, for screws with thread M 5. Dimensions (approx. dimensions) Inner Ø: 5.3 mm Outer Ø: 10 mm Thickness t: 1 mm Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 504240

Washer according to DIN EN ISO 7089, for screws with thread M 6. Dimensions (approx. dimensions) Inner Ø: 6.4 mm Outer Ø: 12.5 mm Thickness t: 1.6 mm Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 234020

NIEDAX - Make: U.S. M8
washer, steel according to DIN EN ISO 7089, DIN 50961 zinc plated, blue passivated, for screws with thread M 8 NIEDAX Model No.: U.S. M8. Type: USM8




Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 245423

Weitspannträgerklemme, zur Klemmbefestigung von Kabelrinnen, Kabel- und Steigeleitern, Weitspannkabelrinnen und -leitern an waagerecht kreuzenden Tägern, eine versetzt angeordnete Anordnung der Klemme verhindert eine Bewegung in Längsrichtung während der Montage, zwei Kerbstellen am Klemmschenkel ermöglichen eine Anpassung des Schenkels an kürzere Trägerflansche, einschließlich galvanisch verzinktes Befestigungszubehör für Kabelrinnen 2 FLM 6X12 V sowie feuerverzinktes Befestigungszubehör für Kabel- und Steigeleitern und Weitspannkabelrinnen /-leitern 2 FLM 8X13 F. Verwendung für : Kabelrinnen RL ... / RLU ... RLV ... RLCI ... RS .... / RSU ... RLC ... / RLUC ... RLCPV ... Verwendung für : Kabel- und Steigeleitern KSL ... Verwendung für : Weitspannkabelrinnen WRL ... WRLM ... WRU ... Verwendung für : Weitspannkabelleitern WSLM ... WSLS ... Abmessungen (ca. Maße) Höhe H x Breite B x Materialstärke t : 82 x 150 x 2 mm Flanschstärke des Trägers t : 8 - 22 mm Werkstoff : Stahl, bandverzinkt nach DIN EN 10346
Sales unit: 20 pieces
Lieske Part No.: 691755

E-clips, screw clamp, for screwing onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 32 - 47 mm Width B: 70 mm for threaded rod through hole: Ø 14 mm Load capacity F: 1.1 kN Material: steel, hot-dip galvanized
Sales unit: 25 pieces
Lieske Part No.: 144911