Screw in Fixing hardware

Flat head screw with hexagon socket according to DIN 7380. Dimensions (approx. dimensions) Thread: M 8 Length L: 16 mm Wrench size: SW 5 Material: Steel, hot-dip galvanized according to DIN EN ISO 1461
Sales unit: 50 pieces
Lieske Part No.: 1102149

E-clips, screw clamp, for screwing onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 1 - 18 mm Height H: 40 mm Support width B: 22 mm for connecting threaded rod: M 10 Load capacity F: 0.6 kN Material: Steel, galvanized/chromated in accordance with DIN 50021
Sales unit: 25 pieces
Lieske Part No.: 862032

Cup screw, including hexagon nut and washer according to DIN EN ISO 7093-1, for fastening the cable ladder fastening ULKG and HSK 15 E3 to the boom KTA.... Dimensions (approx. dimensions) Thread: M 6 Thread length L: 30 mm Max. screw tightening torque: 7 Nm Material: Stainless steel, material no. 1.4401, 1.4404
Lieske Part No.: 193600

Cover fastening, consisting of plastic rivet and screw, for fastening the GRP cable tray/cable ladder covers as well as GRP cable tray and cable ladder fitting covers, halogen-free. A hole Ø 8.2 mm is required to fasten the cover. When fastening, ensure that under normal conditions 2 pieces per meter are attached alternately. Due to external influences, such as wind loads, the number of cover fastenings must be increased. . Can be used for: GRP cable tray/cable ladder cover KKD... GRP cable tray cover KPD... GRP cover for cable tray BKDR 200, BKDR 300 and BKDR 400 GRP cable tray fitting cover Bend 45° KKCD... Bend 90° KKBD... Bend 90°, small KKWD... Gutter riser bend KKBID... Gutter fall bend KKBAD... Level KKETD... Attachment T-piece, small KKSSD... Attachment T-piece, large KKSTD... Reduction, right KKRRD... Reduction, left KKRLD... GRP cable ladder fitting cover Bend 90° ULBD... Bend 90°, large ULBGD... Bend 2x45° ULBAD... T-piece ULTED... Crossing ULXD... Dimensions (approx. dimensions) Rivet Ø: 9 mm Rivet height: 14 mm Rivet plate : Ø 20 mm Material : PA (polyamide) Colour : black RAL : 9005 (similar)
Sales unit: 50 pieces
Lieske Part No.: 587017

E-clips, flange claw, for hammering onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 8 - 14 mm Clamping depth C: 33 mm Mounting distance to support flange B: 7.5 mm Side and bottom connection: M 6 Connection hole: Ø 7 mm Load capacity F: 0.45 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 100 pieces
Lieske Part No.: 537586

E-clips, screw clamp, for screwing onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 1 - 23 mm Height H x Width B: 54 x 49 mm Width of lower leg A: 59 mm for connecting threaded rod: M 12 Load capacity F: 3 kN Material: Steel, galvanized/chromated in accordance with DIN 50021
Sales unit: 25 pieces
Lieske Part No.: 336117

E-clips, screw clamp, for screwing onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 1 - 19 mm Height H x Width B: 45 x 42 mm Width of lower leg A: 50 mm for threaded rod through hole: Ø 9 mm Load capacity F: 2.35 kN Material: Steel, galvanized/chromated in accordance with DIN 50021
Sales unit: 25 pieces
Lieske Part No.: 537588

Flat head screw with slot according to DIN EN ISO 1580, for fixing the perforated cable trays on the rail 2970 with the diagonal sliding nut GSF 0406. Can be used for: Divider fastening clamp KLWC 11 Cable ladder end outlet plate KLAB ... Divider fastening clamp KLWC 16 Wide span cable ladder end outlet plate WLAB ... Dimensions (approx. dimensions) L: 12 mm Thread: M 6 Material: Steel, galvanized according to DIN EN ISO 4042, blue passivated.
Sales unit: 25 pieces
Lieske Part No.: 263685

Flat head screw similar to DIN EN ISO 1580, including flange nut and washer similar to DIN EN ISO 7089, halogen-free. Dimensions (approx. dimensions) Thread: M 8 Thread length L: 20 mm Max. screw tightening torque: 3 Nm Material: PA (polyamide)
Lieske Part No.: 204949

Round-head screw according to DIN 603, including body washer according to DIN EN ISO 7093-1 and toothed flange nut according to DIN EN 1661, for cable tray fastening on perforated anchor rails. Dimensions (approx. dimensions) L: 45 mm Thread: M 6 Material: galvanized according to DIN EN ISO 4042, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 161523

Round-head screw according to DIN 603, including body washer according to DIN EN ISO 7093-1 and toothed flange nut according to DIN EN 1661, for cable tray fastening on perforated anchor rails. Dimensions (approx. dimensions) L: 45 mm Thread: M 6 Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 50 pieces
Lieske Part No.: 654327

Round-head screw according to DIN 603, including body washer according to DIN EN ISO 7093-1 and toothed flange nut according to DIN EN 1661, for cable tray fastening on perforated anchor rails. Dimensions (approx. dimensions) L: 60 mm Thread: M 6 Material: galvanized according to DIN EN ISO 4042, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 169249

Round-head screw according to DIN 603, including body washer according to DIN EN ISO 7093-1 and toothed flange nut according to DIN EN 1661, for cable tray fastening on perforated anchor rails. Dimensions (approx. dimensions) L: 45 mm Thread: M 8 Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 50 pieces
Lieske Part No.: 540873

Round head screw similar to DIN 603, including toothed flange nut according to DIN EN 1661. Dimensions (approx. dimensions) Thread: M 12 Length L: 30 mm Strength class: 8.8 Material: Steel, hot-dip galvanized according to DIN EN ISO 1461
Sales unit: 10 pieces
Lieske Part No.: 444195

Flat head screw similar to DIN 603, including toothed flange nut according to DIN EN 1661. For use in functional maintenance please observe additional regulations! Dimensions (approx. dimensions) L: 12 mm Thread: M 6 Screw material: stainless steel, material no. 1.4571 Flange nut material: stainless steel, material no. 1.4401, 1.4404
Sales unit: 50 pieces
Lieske Part No.: 247607

Round-head screw similar to DIN 603, including toothed flange nut according to DIN EN 1661. For use in functional maintenance or for suspended ceilings with fire protection requirements (model pipe system guideline MLAR 2/2015), please observe additional regulations! Dimensions (approx. dimensions) Thread: M 6 Length L: 12 mm Strength class: 4.8 Material: Steel, hot-dip galvanized according to DIN EN ISO 1461
Sales unit: 50 pieces
Lieske Part No.: 957748

Round-head screw similar to DIN 603, including toothed flange nut according to DIN EN 1661. For use in functional maintenance or for suspended ceilings with fire protection requirements (model pipe system guideline MLAR 2/2015), please observe additional regulations! Dimensions (approx. dimensions) Thread: M 6 Length L: 16 mm Strength class: 4.8 Material: Steel, hot-dip galvanized according to DIN EN ISO 1461
Sales unit: 10 pieces
Lieske Part No.: 179514

Round head screw similar to DIN 603, with toothed flange nut according to DIN EN 1661. Dimensions (approx. dimensions) Thread: M 6 Length: 20 mm Material: Stainless steel, material no. 1.4401, 1.4404
Sales unit: 100 pieces
Lieske Part No.: 185163

Round head screw similar to DIN 603, with toothed flange nut according to DIN EN 1661. Dimensions (approx. dimensions) Thread: M 6 Length: 20 mm Material: Steel, Geomet galvanized (zinc/aluminium flake coating)
Sales unit: 100 pieces
Lieske Part No.: 193141

Round head screw similar to DIN 603, with toothed flange nut according to DIN EN 1661. Dimensions (approx. dimensions) Thread: M 6 Length: 20 mm Material: Steel, galvanized according to DIN EN ISO 2081/4042, thick-layer passivated
Sales unit: 100 pieces
Lieske Part No.: 371326

Flat head screw similar to DIN 603, including toothed flange nut according to DIN EN 1661. Dimensions (approx. dimensions) Thread: M 8 Length L: 16 mm Strength class: 8.8 Material: Steel, hot-dip galvanized according to DIN EN ISO 1461
Lieske Part No.: 339119

GRIPPLE adapter M 6, transition adapter for attaching the GRIPPLE rope systems to a component. The load-bearing capacity F only applies if the anchoring to the supporting surface is sufficient and the installation is carried out in accordance with the regulations. Dimensions (approx. dimensions) Thread: M 6 Thread length: 20 mm for rope Ø: 1.5 - 3 mm Drill Ø: 7 mm Load-bearing capacity F: 0.9 kN (5 times the safety against breakage depending on the rope thickness of the rope system used) Material: Steel, galvanized
Sales unit: 10 pieces
Lieske Part No.: 877084

GRIPPLE wire rope cutter, special tool for cutting GRIPPLE wire ropes made of galvanized steel or stainless steel, clean cutting prevents the wire rope ends from splicing. Dimensions (approx. dimensions) for rope diameter: 1.5 - 3 mm
Lieske Part No.: 917165

Suspension No. 1, 2, 3 threaded end L = 3 meter
assembly / type: Ø 1 mm
Execution: No. 1: supports up to 10 kg Type: GAG-1/3


Package: 10 PCS.
Sales unit: 10 pieces
Lieske Part No.: 661812

No suspension
with cross-anchoring L = 5 meters - supports up to
kg, Ø: ca
mm Component / Type: Threaded End Type: GAG
/ 5 item:
ST.
Sales unit: 10 pieces
Lieske Part No.: 537209

No suspension
, 2, 3 threaded end L = 3 meter assembly / type: Ø 2 mm Finish: # 2: supports up to 9 kg Type: GAG-3/3 Quantity:
ST.
Sales unit: 10 pieces
Lieske Part No.: 764677

Suspension No. 1, 2, 3 threaded end L = 3 meters
Assembly / type: Ø 3 mm
Type: 3: supports up to 90 kg

Type: GAG-3/3
Package: 10 PCS.
Sales unit: 10 pieces
Lieske Part No.: 173601

GRIPPLE set hooks, quick suspension system, versatile and ready to use, for attachment to supports, mesh cable trays, profile clamps, flange claws, loops and eyelets. The load-bearing capacity F only applies to correct assembly. Set consists of: 1 cut wire rope with a hook at the end 1 self-locking GRIPPLE for quick attachment 1 GRIPPLE adjustment/release pin (1x included for each smallest unit) Dimensions (approx. dimensions) Rope Ø: 2 mm Rope length L: 1 m Load-bearing capacity F: 0.45 kN (5-fold safety against breakage) Wire rope material: steel, galvanized
Sales unit: 10 pieces
Lieske Part No.: 278718

No suspension
, 2, 3 with loop L = 3 meter assembly / type: Ø ca
mm Design: No
: Loads up to
kg Type: GAK
/ 3 Quantity:
ST.
Sales unit: 10 pieces
Lieske Part No.: 882863

No suspension
with cross-anchoring L = 5 meters - supports up to
kg, Ø: ca
mm Component / Type: with loop type: GAK
/ 5 item:
ST.
Sales unit: 10 pieces
Lieske Part No.: 918918

No suspension
, 2, 3 with loop L = 3 meter assembly / type: Ø 2 mm Finish: # 2: loads up to 45 kg Type: GAK-2/3 Quantity:
ST.
Sales unit: 10 pieces
Lieske Part No.: 906754

Suspension No. 1, 2, 3 with loop L = 3 meters
Assembly / type: Ø 3 mm
Type: 3: supports up to 90 kg

Type: GAC-3/3
Package: 10 PCS.
Sales unit: 10 pieces
Lieske Part No.: 234786

No suspension
, 2, 3 with L = 3 m cross-anchoring assembly / type: Ø ca
mm Design: No
: Supports up to
kg Type: GAQ-
/ 3 Quantity:
ST.
Sales unit: 10 pieces
Lieske Part No.: 972484

No suspension
with cross-anchoring L = 5 meters - supports up to
kg, Ø: ca
mm Component / Type: with cross-anchoring Type: GAQ-
/ 5 item:
ST.
Sales unit: 10 pieces
Lieske Part No.: 824585

Suspension No. 1, 2, 3 with L = 3 m cross-anchoring
assembly / type: Ø 2 mm
Finish: # 2: loads up to 45 kg Type: GAQ-2/3


Package: 10 PCS.
Sales unit: 10 pieces
Lieske Part No.: 670648

GRIPPLE set cross anchor, quick suspension system, versatile and ready to use, for attachment to sheet steel roofs and suspended ceilings. The load-bearing capacity F only applies to correct installation. Set consists of: 1 cut-to-length wire rope with cross anchor for drill hole and end sleeve 1 self-locking GRIPPLE for quick attachment 1 GRIPPLE adjustment/release pin (1x included for each smallest PU) Dimensions (approx. dimensions) Rope Ø: 3 mm Rope length L: 3 m Drill hole Ø: 10 mm Permissible load-bearing capacity F: 0.9 kN (5-fold safety against breakage) Wire rope material: steel, galvanized
Sales unit: 10 pieces
Lieske Part No.: 426864

GRIPPLE trapezoidal hook and express fastener, quick suspension system, versatile and ready to use, for fastening to trapezoidal sheet metal ceilings. The load-bearing capacity F only applies if the ceiling is sufficiently anchored to the supporting surface and installed correctly. Make sure that the selected end is suitable for the respective support structure and follow the manufacturer's recommendations for all installations. Set consists of: 1 cut-to-length wire rope with trapezoidal sheet hook 1 self-locking GRIPPLE for quick fastening with express fastener (integrated adjustment system) Dimensions (approx. dimensions) Rope Ø: 2 mm Rope length L: 1 m Hook Ø: 5 mm Load-bearing capacity F: 0.45 kN (5-fold safety against breakage was calculated on a 2 mm trapezoidal sheet) Wire rope material: steel, galvanized
Sales unit: 10 pieces
Lieske Part No.: 169250

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width Dimensions (approx. dimensions) Length L: 50 mm Width B: 21 mm Sliding nut height H: 17 mm Thread: M 10 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: grey polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 697283

Sliding nut with fixing aid, for C anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2996Z with 22 mm slot width wall bracket STRUT HKC 96Z/... hanging post and wall bracket STRUT HKC 96ZD/... Dimensions (approx. dimensions) Length L: 50 mm Width B: 25 mm Sliding nut height H: 18 mm Thread: M 10 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: gray polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 239560

Sliding nut with fixing aid, for C-anchor rails, for anchor rails with 18 mm slot width can only be used from the profile end with a fastening screw, not suitable in combination with the anchor rail 2986-1.75... for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on. Use for: anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width Dimensions (approx. dimensions) Length L: 50 mm Width B: 21 mm Sliding nut height H: 17 mm Thread: M 12 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: grey polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 1332945

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2996Z with 22 mm slot width wall bracket STRUT HKC 96Z/... hanging post and wall bracket STRUT HKC 96ZD/... Dimensions (approx. dimensions) Length L: 50 mm Width B: 25 mm Sliding nut height H: 18 mm Thread: M 12 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: gray polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 740765

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width Dimensions (approx. dimensions) Length L: 50 mm Width B: 21 mm Sliding nut height H: 17 mm Thread: M 6 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: grey polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 1332811

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2996Z with 22 mm slot width wall bracket STRUT HKC 96Z/... hanging post and wall bracket STRUT HKC 96ZD/... Dimensions (approx. dimensions) Length L: 50 mm Width B: 25 mm Sliding nut height H: 18 mm Thread: M 6 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: gray polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 1332944

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width Dimensions (approx. dimensions) Length L: 50 mm Width B: 21 mm Sliding nut height H: 17 mm Thread: M 8 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: grey polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 168388

Sliding nut with fixing aid, for C-anchor rails, for precise fixing without slipping, especially in vertical applications, the sliding nut is screwed into the profile by 90° using the fixing aid and can be variably positioned by pressing on, can be used at any point in the profile. Use for: anchor rails/profile rails 2996Z with 22 mm slot width wall bracket STRUT HKC 96Z/... hanging post and wall bracket STRUT HKC 96ZD/... Dimensions (approx. dimensions) Length L: 50 mm Width B: 25 mm Sliding nut height H: 18 mm Thread: M 8 Strength class: 8 Sliding nut material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684 Fixing aid material: gray polyamide (PA), halogen-free
Sales unit: 100 pieces
Lieske Part No.: 193567

Sliding nut, without screw, can be used at any point with a fastening screw in the profile. Please observe additional regulations for use in functional maintenance! Use for: Anchor rails/profile rails 2985, 2986, 2988 and 2990 with 18 mm slot width 2996Z with 22 mm slot width Wall bracket STRUT HKC 96Z/... Hanging post and wall bracket HKC 96ZD/... Dimensions (approx. dimensions) Length L: 34 mm Width B: 15.5 mm Height H: 10 mm Thread: M 10 Strength class: 8 Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461/10684
Sales unit: 100 pieces
Lieske Part No.: 746614

NIEDAX - Make: GMZ M
2 F sliding nut, steel, channel bars for C-Model 2985, 2986, 2988 and 299 with slot width
8 mm (usable only by the end of the profile) and for C-anchor rails model 2987, 299
, 2992, 2994, 2995, 2996 and 2996Z with 22/26 mm slot width, GMZ M
2 F can be used at any point in the profile with fixing screw, hot-dip galvanized to DIN EN ISO
684th Dimensions L x W: 34 x
8 mm height of the sliding nut:
mm with thread M
2 Property class: 8 NIEDAX model no. GMZ M
2 F Type: GMZM
2F sales unit:
ST.
Sales unit: 100 pieces
Lieske Part No.: 749335

Gitterrinnen-Befestigungsklemme, horizontal/vertikal, zur Befestigung von Gitterrinnen an horizontalen und vertikalen Stahlträgerflanschen, eine wechselseitige Anordnung der Hakenschrauben gewährleistet eine sichere Befestigung der Gitterrinne an der Gitterrinnen-Befestigungsklemme, eine rechtwinklige Aussparung in den Schenkeln ermöglicht eine Anbringung an runden Stützenprofilen oder eine Montage von Kabelschutzrohren = Ø 30 mm, bei horizontaler Montage kann eine zusätzliche Abhängung mittels Gewindestab M 10/... an der Befestigungsklemmenspitze durch eine Lochung Ø 11 mm erfolgen, stirnseitig kann überdies eine Schraubabstandsschelle SASS 30 befestigt werden, durch Auslässe in der horizontalen Auflagefläche besteht die Möglichkeit zur Montage von bis zu 4 Bügelschellen B(K) 12 - 90 (je nach Größe) in Registerverlegung, einschließlich anteilmäßigen Befestigungszubehör aus Edelstahl, Werkstoff Nr. 1.4301, AISI 304. Verwendung für Gitterrinnen : GR... GRS... GRL... GRCI... MTC...100 - ... MTCG ... Abmessungen (ca. Maße) Gesamtlänge L : 173 mm Auflagelänge L1 : 148 mm Stahlträgerflanschstärke : = 20 mm Tragfähigkeit F1 horizontal bei L 1/2 : 0,6 kN Tragfähigkeit F2 vertikal bei L 1/2 : 0,9 kN Schraubenanzugsmoment : 4 Nm Werkstoff : Stahl, tauchfeuerverzinkt nach DIN EN ISO 1461 Verkaufseinheit: 1 ST.
Sales unit: 10 pieces
Lieske Part No.: 832935

Gitterrinnen-Befestigungsklemme, horizontal/vertikal, zur Befestigung von Gitterrinnen an horizontalen und vertikalen Stahlträgerflanschen, eine wechselseitige Anordnung der Hakenschrauben gewährleistet eine sichere Befestigung der Gitterrinne an der Gitterrinnen-Befestigungsklemme, eine rechtwinklige Aussparung in den Schenkeln ermöglicht eine Anbringung an runden Stützenprofilen oder eine Montage von Kabelschutzrohren = Ø 30 mm, bei horizontaler Montage kann eine zusätzliche Abhängung mittels Gewindestab M 10/... an der Befestigungsklemmenspitze durch eine Lochung Ø 11 mm erfolgen, stirnseitig kann überdies eine Schraubabstandsschelle SASS 30 befestigt werden, durch Auslässe in der horizontalen Auflagefläche besteht die Möglichkeit zur Montage von bis zu 4 Bügelschellen B(K) 12 - 90 (je nach Größe) in Registerverlegung, einschließlich anteilmäßigen Befestigungszubehör. Verwendung für Gitterrinnen : GR... GRS... GRL... GRCI... MTC...100 - ... MTCG ... Abmessungen (ca. Maße) Gesamtlänge L : 173 mm Auflagelänge L1 : 148 mm Stahlträgerflanschstärke : = 20 mm Tragfähigkeit F1 horizontal bei L 1/2 : 0,6 kN Tragfähigkeit F2 vertikal bei L 1/2 : 0,9 kN Schraubenanzugsmoment : 4 Nm Werkstoff : Stahl, bandverzinkt nach DIN EN 10346 Verkaufseinheit: 1 ST.
Sales unit: 10 pieces
Lieske Part No.: 696019

Hook screw with M 6 thread, including toothed special flange nut similar to DIN EN 1661, for fastening the mesh cable trays to brackets, to mesh cable tray hanging posts, and to joint connectors. Please note additional regulations for use in functional maintenance! Can be used for: mesh cable trays up to max. 6 mm wire thickness Dimensions (approx. dimensions) Thread: M 6 Thread length: 15 mm Flange nut: Ø 17 mm Material: steel, galvanized in accordance with DIN EN ISO 4042, blue passivated.
Lieske Part No.: 187895