Installation with push-in clamps requires no additional tools or pipe clamps. Ready to use out of the box, saving installation time and labor. Plastic clamps and base are non-corrosive to pipes. Push-in clamps are available in 2 sizes to suit the project. The base has a variety of holes to accommodate different clamp sizes and configurations. Additional push-in clamps can be purchased separately to attach additional pipe runs. Foamed pad provides a low abrasion surface for better protection of the roof covering. Provides superior load distribution, even on uneven roof surfaces. Compatible with roof surfaces including single ply, bituminous materials, metal and spray foam. Available in multiple sizes and with different load capacities, the system can be customized to suit the application. Easy to transport to the roof.
Sales unit: 10 pieces
Lieske Part No.: 1342344

Installation with push-in clamps requires no additional tools or pipe clamps. Ready to use out of the box, saving installation time and labor. Plastic clamps and base are non-corrosive to pipes. Push-in clamps are available in 2 sizes to suit the project. The base has a variety of holes to accommodate different clamp sizes and configurations. Additional push-in clamps can be purchased separately to attach additional pipe runs. Foamed pad provides a low abrasion surface for better protection of the roof covering. Provides superior load distribution, even on uneven roof surfaces. Compatible with roof surfaces including single ply, bituminous materials, metal and spray foam. Available in multiple sizes and with different load capacities, the system can be customized to suit the application. Easy to transport to the roof.
Sales unit: 5 pieces
Lieske Part No.: 1264418

Pedestal that uses a strut mounting rail to provide a fixed height mounting platform off the roof surface. Hot dip galvanized C-section strut mounting rail, 152mm long, 122mm high and hardware.
Sales unit: 20 pieces
Lieske Part No.: 1329280

Pedestal that provides a fixed height mounting platform on the roof surface with a strut mounting rail. Hot dip galvanized C-profile strut mounting rail, 254 mm long, 122 mm high.
Sales unit: 10 pieces
Lieske Part No.: 1329279

Pedestal that uses a strut mounting rail to provide a fixed height mounting platform away from the roof surface. Hot dip galvanized C-profile strut mounting rail, 254mm long, 163mm high.
Sales unit: 5 pieces
Lieske Part No.: 1329278

Provides superior load-bearing capacity for pipes, conduits, ducts, cable trays and equipment. Foamed overlay provides a low abrasion surface for better protection of roof covering. Compatible with roof surfaces including single ply, bituminous materials, metal and spray foam. Provides superior load distribution, even on uneven roof surfaces. Ready to use out of the box, saving installation time and labor. Available in multiple sizes and load capacities, the system can be customized to suit the application. Easy to transport to the roof. Hot-dip galvanized and UV stabilized for long life.
Sales unit: 5 pieces
Lieske Part No.: 1261730

Base with strut mounting rail profile that allows height changes away from the roof surface. Ready-to-use, immediately deployable solution with hot-dip galvanized strut mounting rail profile and hardware. 254 mm long, height adjustable 152-330 mm.
Sales unit: 5 pieces
Lieske Part No.: 1337337

Standfuß mit Strutmontageschienenprofil, die Höhenänderungen abseits der Dachfläche ermöglicht. Gebrauchsfertige, sofort einsatzber. Lösung mit feuerverz. Strutmontageschienenprofil u. Hardware. 406 mm lang, höhenverstellbar 178-457 mm.
Lieske Part No.: 514201

Extra wide base that uses a strut mounting rail to provide a fixed height mounting platform away from the roof surface. Hot dip galvanized A-profile strut mounting rail, 610mm long, 142mm high.
Sales unit: 2 pieces
Lieske Part No.: 2068331

Installation with push-in clamps is done without additional tools or pipe clamps. The push-in clamps are available in 2 sizes to suit the project. Plastic clamps and base do not have a corrosive effect on the pipes.
Sales unit: 100 pieces
Lieske Part No.: 1342075

Installation with push-in clamps is done without additional tools or pipe clamps. The push-in clamps are available in 2 sizes to suit the project. Plastic clamps and base do not have a corrosive effect on the pipes.
Sales unit: 100 pieces
Lieske Part No.: 1343705

Self-locking stainless steel nuts allow for application-specific attachment to the support base, including easy attachment of stainless steel mounting rails, threaded rods or project-specific fasteners. Foamed overlay provides a low abrasion surface for better protection of the roof covering. Compatible with roof surfaces including single ply, bituminous materials, metal and spray foam. Provides superior load distribution, even on uneven roof surfaces. Available in multiple sizes and load capacities, the system can be customized to meet application requirements. Includes square mounting rail slots to create a 305mm wide H-frame (PBUM16 only). Base is UV stabilized thermoplastic material.
Sales unit: 20 pieces
Lieske Part No.: 1342077

Self-locking stainless steel nuts allow for application-specific attachment to the support base, including easy attachment of stainless steel mounting rails, threaded rods or project-specific fasteners. Foamed overlay provides a low abrasion surface for better protection of the roof covering. Compatible with roof surfaces including single ply, bituminous materials, metal and spray foam. Provides superior load distribution, even on uneven roof surfaces. Available in multiple sizes and load capacities, the system can be customized to meet application requirements. Includes square mounting rail slots to create a 305mm wide H-frame (PBUM16 only). Base is UV stabilized thermoplastic material.
Sales unit: 10 pieces
Lieske Part No.: 2068390

Self-locking stainless steel nuts allow for application-specific attachment to the support base, including easy attachment of stainless steel mounting rails, threaded rods or project-specific fasteners. Foamed overlay provides a low abrasion surface for better protection of the roof covering. Compatible with roof surfaces including single ply, bituminous materials, metal and spray foam. Provides superior load distribution, even on uneven roof surfaces. Available in multiple sizes and load capacities, the system can be customized to meet application requirements. Includes square mounting rail slots to create a 305mm wide H-frame (PBUM16 only). Base is UV stabilized thermoplastic material.
Sales unit: 5 pieces
Lieske Part No.: 2068391

The locking pins are installed without tools. Locking pins and bases do not corrode. Pins and mounting holes match almost all perforated cable trays. Ready to use out of the box, saves installation time and labor. Additional pins can be purchased separately. Foamed pad provides a low abrasion surface for better protection of the roof covering. Provides superior load distribution, even on uneven roof surfaces. Compatible with roof surfaces including single ply, bituminous materials, metal and spray foam. Available in several sizes and with different load capacities, the system can be customized to suit the application. Easy to transport to the roof.
Sales unit: 20 pieces
Lieske Part No.: 1264414

Tool-free, perforated cable tray support kit that provides a fixed height of 4¿ (102 mm) above the roof surface. 12 1/2¿ (317.5 mm) long, ready to use, includes insertion pins. LEED qualified.
Sales unit: 10 pieces
Lieske Part No.: 1264413

The locking pins are installed without tools. Locking pins and bases do not corrode. Pins and mounting holes fit almost all perforated cable trays.
Sales unit: 10 pieces
Lieske Part No.: 1264412

The locking pins are installed without tools. Locking pins and bases do not corrode. Pins and mounting holes match almost all perforated cable trays. Ready to use out of the box, saves installation time and labor. Additional pins can be purchased separately. Foamed pad provides a low abrasion surface for better protection of the roof covering. Provides superior load distribution, even on uneven roof surfaces. Compatible with roof surfaces including single ply, bituminous materials, metal and spray foam. Available in several sizes and with different load capacities, the system can be customized to suit the application. Easy to transport to the roof.
Lieske Part No.: 1264411

CADDY CN connecting link
Diameter in mm: 3.0 mm Type: KN30


Item: 100 ST.
Lieske Part No.: 229684

CADDY CN connecting link
diameter in mm: 4.0 mm Type: KN40


Item: 100 ST.
Lieske Part No.: 639053

CADDY CN connecting link
Diameter in mm: 5.0 mm

Type: KN50
Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 122914

Mounting rail for the production of trapezes, structures and bracing, type A. 2 meters of back-perforated, pre-galvanized mounting rail, 41 x 41 x 2.5 mm.
Sales unit: 10 pieces
Lieske Part No.: 232807

CADDY TKN bracket for threaded rods M6, M8, M10, M12 diameters in mm: M6 Type: TKN / M6 Quantity: 140 ST.
Sales unit: 140 pieces
Lieske Part No.: 193560

CADDY TKN clamp for threaded rod M6, M8, M
, M
2 mm in diameter: M8 Type: TKNM8 P

ST.
Lieske Part No.: 842259

CADDY TKN clip
for threaded rods M6, M8, M10, M12
Diameter in mm: M10

Type: TKN/M10
Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 134091

Mounting rail for the production of trapezes, structures and bracing, type C. 2 meters of back-perforated, pre-galvanized mounting rail, 21 x 41 x 2.5 mm.
Sales unit: 10 pieces
Lieske Part No.: 943961

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 10 pieces
Lieske Part No.: 441021

For securing objects to nVent CADDY Eristrut rails.
Sales unit: 25 pieces
Lieske Part No.: 1316713

Washer for installation in conjunction with mounting rails.
Lieske Part No.: 2068179

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 25 pieces
Lieske Part No.: 199740

For making metal frames with nVent CADDY Eristrut rails.
Lieske Part No.: 577296

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 25 pieces
Lieske Part No.: 1316712

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 10 pieces
Lieske Part No.: 438788

For making metal frames with nVent CADDY Eristrut rails.
Lieske Part No.: 913425

Flat angle for making frames and structures with mounting rails.
Sales unit: 10 pieces
Lieske Part No.: 489215

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 25 pieces
Lieske Part No.: 581702

For making metal frames with nVent CADDY Eristrut rails.
Lieske Part No.: 765022

90° mounting bracket for creating strut mounting rail frames and structures, 2 holes. Hot dip galvanized steel, 1-1 mounting bracket, 50mm x 48mm. Right, 90 degree angle.
Sales unit: 10 pieces
Lieske Part No.: 1316707

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 10 pieces
Lieske Part No.: 1262638

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 10 pieces
Lieske Part No.: 989626

For making metal frames with nVent CADDY Eristrut rails.
Lieske Part No.: 181893

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 10 pieces
Lieske Part No.: 315762

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 10 pieces
Lieske Part No.: 248060

90° mounting bracket for creating strut mounting rail frames and structures, 4 holes. Hot-dip galvanized steel, 2-2 hole angle connector, 102 mm x 86 mm.
Sales unit: 10 pieces
Lieske Part No.: 1316706

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 10 pieces
Lieske Part No.: 1262637

Reinforced 90° mounting bracket for creating strut mounting rail frames and structures, 4 holes. Hot dip galvanized steel, 2-2 hole corner bracket, right hand, 106mm x 89mm.
Lieske Part No.: 141253

Angles for mounting rails for creating frames and structures.
Lieske Part No.: 1316748

Complete with U-bolts and nuts. Assembly in pairs required.
Lieske Part No.: 2068229

T-shaped mounting bracket for creating strut mounting rail frames and structures. Hot dip galvanized steel, triple, double corner connector with eight holes, 43 mm x 140 mm x 102 mm.
Lieske Part No.: 562060

For making metal frames with nVent CADDY Eristrut rails.
Sales unit: 5 pieces
Lieske Part No.: 721506