Clamps in Fixing hardware

Kabeltragwannensystem, für die Wandmontage oder zur Befestigung an Schienen. In Anlehnung an die VDE 0298-565-1 und VDE 0298-565-2 sollte ein max. Stützabstand von 0,8 m nicht überschritten werden. Die Tragfähigkeitsangaben gelten nur bei ausreichender Verankerung mit dem tragenden Untergrund und wenn im Klemmbereich die Oberflächen der vertikal verlaufenden Profil-/Ankerschienen und der Wannentragschienen aus Stahl oder verzinktem Stahl sind. Ist der Klemmbereich mit einem Farbanstrich versehen, muss dieser entfernt werden, da sonst die Tragfähigkeit nicht gegeben bzw. gewährleistet ist. Gefahr des Abrutschens! 1. Das Kabeltragwannensystem in den Wannenbreiten 40, 50, 60, 70, 80 und 120 mm auf Anfrage als Sonderanfertigung lieferbar. Befestigungsmaterial muss, je nach Anwendungsfall, gesondert bestellt werden. Abmessungen (ca. Maße) Wanne B x L : 100 x 200 mm Anzahl der Tragwannen übereinander : 5 Abstand der Tragwannen : 100 mm Tragfähigkeit F bei B/2 : 0,5 kN Schiene H x B : 485 x 72 mm Schienenlochung : 11 x 16 mm mittiger Lochabstand : 100 mm Anzahl der Lochung : 5 Werkstoff : Stahl, tauchfeuerverzinkt nach DIN EN ISO 1461 Verkaufseinheit: 1 ST.
Lieske Part No.: 509654

NIEDAX - Make: LW 16
Long trough for clamp clamp type B 16, BA 16, BU 16, BF 16 and BW 16, from steel strip galvanized to DIN EN 10346th Additionally approved for function maintenance to DIN 4102, Part 12.1.91, if the boundary conditions are fulfilled for integrity and then only for the Band type B 16 + BU 16

for cable diameter: 8 - 13 mm

L Length: 200 mm

NIEDAX model no. LW 16

Type: LW16
Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 150979

NIEDAX - Make: LW 22 long trough for clamp clamp type B 22, BA 22, BU 22, BF 22 and BW 22, from steel strip galvanized to DIN EN
346th Additionally approved for function maintenance to DIN 4
2, part
2 /
.9
If the conditions are met for integrity and then only for the Band type B 22 + BU 22 for cable diameter:
3 -
9 mm Length L: 2 mm NIEDAX model no. LW 22 Type: LW22 item:
ST.
Sales unit: 100 pieces
Lieske Part No.: 845505

NIEDAX - Make: LW 26
long trough for clamp clamp type B 26, BA 26, BU 26, BF 26 and BW 26, from steel strip galvanized to DIN EN 10346th Additionally approved for function maintenance to DIN 4102, Part 12.1.91, if the boundary conditions are fulfilled for integrity and then only for the Band type B 26 + BU 26 for cable diameters 19 - 23 mm



L Length: 200 mm

NIEDAX model no. LW 26 Type: LW26


Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 370240

NIEDAX - Make: LW 34
long trough for clamp clamp type B 34, BA 34, BU 34, BF 34 and BW 34, from steel strip galvanized to DIN EN 10346th Additionally approved for function maintenance to DIN 4102, Part 12.1.91, if the boundary conditions are fulfilled for integrity and then only for the Band type B 34 + BU 34 for cable diameters 23 - 31 mm



L Length: 200 mm

NIEDAX model no. LW 34 Type: LW34


Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 635644

NIEDAX - Make: LW 38
long trough for clamp clamp type B 38, BA 38, BU 38, BF 38 and BW 38, from steel strip galvanized to DIN EN 10346th Additionally approved for function maintenance to DIN 4102, Part 12.1.91, if the boundary conditions are fulfilled for integrity and then only for the Band type B 38 + BU 38 for cable diameters: 31 - 36 mm



L Length: 200 mm

NIEDAX model no. LW 38 Type: lw38


Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 613556

NIEDAX - Make: LW 42
Long trough for clamp clamp type B 42, BA 42, BU 42, BF 42 and BW 42, from steel strip galvanized to DIN EN 10346th Additionally approved for function maintenance to DIN 4102, Part 12.1.91, if the boundary conditions are fulfilled for integrity and then only for the Band type B 42 + BU 42

for cable diameters 36 - 40 mm

L Length: 200 mm

NIEDAX model no. LW 42

Type: LW42
Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 564796

Long tray, for all U-clamps, to increase the contact surface. For use in functional maintenance, please observe additional regulations! for U-clamp: B ... BA ... BU ... BF ... BW ... in functional maintenance approved for: B ... without counter tray BU ... without counter tray for C-profile rails with slot width: 11 - 12 mm 16 - 17 mm 18 - 22 mm for flat iron with material thickness t: 4 - 12 mm for angle steel, U-iron with a leg length: 40 mm and t= 4 - 6 mm Dimensions (approx. dimensions) for cable Ø: 39 - 43 mm Length L: 200 mm Material: Steel, strip galvanized in accordance with DIN EN 10346
Sales unit: 100 pieces
Lieske Part No.: 545417

NIEDAX - Make: LW 5 long trough for clamp clamp type B 5, 5 BA, BU 5, 5 BF and BW 5, from steel strip galvanized to DIN EN
346th Additionally approved for function maintenance to DIN 4
2, part
2 /
.9
If the conditions are met for integrity and then only for the Band type B 5 + BU 5th for cable diameters 43 - 47 mm Length L: 2 mm NIEDAX Model No.: LW 5 Type: LW5 item.
ST.
Sales unit: 50 pieces
Lieske Part No.: 882897

Long trough, for all U-clamps, to increase the contact surface. For use in functional maintenance, please observe additional regulations! for U-clamp: B ... BA ... BU ... BF ... BW ... in functional maintenance approved for: B ... without counter trough BU ... without counter trough for C-profile rails with slot width: 11 - 12 mm 16 - 17 mm 18 - 22 mm for flat iron with material thickness t: 4 - 12 mm for angle steel, U-iron with a leg length: 40 mm and t= 4 - 6 mm Dimensions (approx. dimensions) for cable Ø: 47 - 51 mm Length L: 200 mm Material: Steel, strip galvanized in accordance with DIN EN 10346
Sales unit: 50 pieces
Lieske Part No.: 893472

Long trough, for all U-clamps, to increase the contact surface. For use in functional maintenance, please observe additional regulations! for U-clamp: B ... BA ... BU ... BF ... BW ... in functional maintenance approved for: B ... without counter trough BU ... without counter trough for C-profile rails with slot width: 11 - 12 mm 16 - 17 mm 18 - 22 mm for flat iron with material thickness t: 4 - 12 mm for angle steel, U-iron with a leg length: 40 mm and t= 4 - 6 mm Dimensions (approx. dimensions) for cable Ø: 51 - 55 mm Length L: 200 mm Material: Steel, strip galvanized in accordance with DIN EN 10346
Sales unit: 50 pieces
Lieske Part No.: 557701

Long trough, for all U-clamps, to increase the contact surface. For use in functional maintenance, please observe additional regulations! for U-clamp: B ... BA ... BU ... BF ... BW ... in functional maintenance approved for: B ... without counter trough BU ... without counter trough for C-profile rails with slot width: 11 - 12 mm 16 - 17 mm 18 - 22 mm for flat iron with material thickness t: 4 - 12 mm for angle steel, U-iron with a leg length: 40 mm and t= 4 - 6 mm Dimensions (approx. dimensions) for cable Ø: 55 - 61 mm Length L: 200 mm Material: Steel, strip galvanized in accordance with DIN EN 10346
Sales unit: 50 pieces
Lieske Part No.: 678117

Long trough, for all U-clamps, to increase the contact surface. For use in functional maintenance, please observe additional regulations! for U-clamp: B ... BA ... BU ... BF ... BW ... in functional maintenance approved for: B ... without counter trough BU ... without counter trough for C-profile rails with slot width: 11 - 12 mm 16 - 17 mm 18 - 22 mm for flat iron with material thickness t: 4 - 12 mm for angle steel, U-iron with a leg length: 40 mm and t= 4 - 6 mm Dimensions (approx. dimensions) for cable Ø: 61 - 67 mm Length L: 200 mm Material: Steel, strip galvanized in accordance with DIN EN 10346
Sales unit: 50 pieces
Lieske Part No.: 212985

Long tray, for all U-clamps, to increase the contact surface. For use in functional maintenance, please observe additional regulations! for U-clamp: B ... BA ... BU ... BF ... BW ... in functional maintenance approved for: B ... without counter tray BU ... without counter tray for C-profile rails with slot width: 11 - 12 mm 16 - 17 mm 18 - 22 mm for flat iron with material thickness t: 4 - 12 mm for angle steel, U-iron with a leg length: 40 mm and t= 4 - 6 mm Dimensions (approx. dimensions) for cable Ø: 67 - 73 mm Length L: 200 mm Material: Steel, strip galvanized in accordance with DIN EN 10346
Sales unit: 50 pieces
Lieske Part No.: 599983

Pole connection holder, with coupling, for crossing fastening of cable protection pipes to the poles of cable trays and cable ladders. Can be used for: Machine installation pipe MI 30... on cable trays RL..., RS... etc. and cable ladders KL... Dimensions (approx. dimensions) for pole clamp width B: = 15 mm Clamp length: 120 mm Coupling Ø: 30 mm Coupling length: 80 mm Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Lieske Part No.: 317845

Beam connection holder, with round steel bracket, for crossing fastening of cable protection pipes to beams of cable trays and cable ladders. Can be used for: Machine installation pipe MI 30... on cable trays RL..., RS... etc. and cable ladders KL... Dimensions (approx. dimensions) for beam clamp width B: = 15 mm Clamp length: 120 mm Round steel bracket Ø: 30 mm Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Lieske Part No.: 125531

Stile connection holder, with round steel bracket, for crossing fastening of cable protection pipes to stiles of wide-span cable trays and wide-span cable ladders. Can be used for: Machine installation pipe MI 30... on wide-span cable trays WRL..., WRLM... and wide-span cable ladders WSL..., WSLM... Dimensions (approx. dimensions) for stile clamp width B: = 30 mm Clamp length: 120 mm Round steel bracket Ø: 30 mm Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Lieske Part No.: 125529

Pole connection holder, with round steel bracket, for crossing fastening of cable protection pipes to the poles of the Allround cable ladders. Can be used for: Machine installation pipe MI 30... on Allround cable ladders KRC... / KRO... Dimensions (approx. dimensions) for cable ladder poles H x W: 60 x 20 mm Clamp length: 120 mm Round steel bracket Ø: 30 mm Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Lieske Part No.: 593760

Stile connection holder, with round steel bracket, for crossing fastening of cable protection pipes to stiles of wide-span cable trays and wide-span cable ladders. Can be used for: machine installation pipe MI 60..., machine installation pipe MIG 60... and installation pipe connection MIA 60... on wide-span cable trays WRL..., WRLM... and wide-span cable ladders WSL..., WSLM... Dimensions (approx. dimensions) for stile clamp width B: = 30 mm Clamp length: 120 mm Round steel bracket Ø: 60 mm Material: steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Lieske Part No.: 125489

Pipe clamp, double-lobed, with mounting holes, for fastening machine installation pipes. Can be used for: Machine installation pipe MI 30... Dimensions (approx. dimensions) Height H x Width W x Length L: 29.5 x 25 x 85 mm Mounting holes: 8.5 x 10 mm Center distance: 60 mm for pipe Ø: 30 mm Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Sales unit: 20 pieces
Lieske Part No.: 125494

Pipe clamp, double-lobed, with mounting holes, for fastening machine installation pipes. Can be used for: Machine installation pipe MI 60... Machine installation pipe MIG 60... Installation pipe connection MIA 60... Dimensions (approx. dimensions) Height H x Width W x Length L: 61 x 30 x 160 mm Mounting holes: 9.5 x 20 mm Center distance: 120 mm for pipe Ø: 60 mm Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Sales unit: 20 pieces
Lieske Part No.: 723807

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 14 - 15 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 50 pieces
Lieske Part No.: 303234

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the cable's terminal space for fastening a cable. Please observe additional regulations for use in functional maintenance! Dimensions (approx. dimensions) W x L: 12 x 35 mm Internal connection thread: M 6 for cable Ø: 10 - 11 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material: Steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no.: SAS 10 V
Sales unit: 50 pieces
Lieske Part No.: 1342451

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation conduits in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric electrical installation conduit. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 12 x 37 mm Internal connection thread : M 6 for cable Ø : 11 - 13 mm for metric electrical installation conduits in accordance with DIN EN 60423 : M 12 Material : steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material : steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no. : SAS 12V
Sales unit: 50 pieces
Lieske Part No.: 1342059

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the cable's terminal space for fastening a cable. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L: 12 x 39 mm Internal connection thread: M 6 for cable Ø: 13 - 15 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material: Steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no.: SAS 14 V
Sales unit: 50 pieces
Lieske Part No.: 1342415

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation conduits in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric electrical installation conduit. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 12 x 41 mm Internal connection thread : M 6 for cable Ø : 15 - 17 mm for metric electrical installation conduits in accordance with DIN EN 60423 : M 16 Material : steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material : steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no. : SAS 16V
Sales unit: 50 pieces
Lieske Part No.: 1342441

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation conduits in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric electrical installation conduit. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 12 x 51 mm Internal connection thread : M 6 for cable Ø : 25 - 27 mm for metric electrical installation conduits in accordance with DIN EN 60423 : M 25 Material : steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material : steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no. : SAS 26 V
Sales unit: 50 pieces
Lieske Part No.: 1342454

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the cable's terminal space for fastening a cable. Please observe additional regulations for use in functional maintenance! Dimensions (approx. dimensions) W x L: 12 x 56 mm Internal connection thread: M 6 for cable Ø: 28 - 30 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material: Steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no.: SAS 30 V
Sales unit: 50 pieces
Lieske Part No.: 1342453

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric pipe. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 16 x 69 mm Internal connection thread : M 6 for cable Ø : 29 - 38 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 32 Material : Steel, galvanized in accordance with DIN EN ISO 2081, thick-film passivated Screw material : Steel, galvanized in accordance with DIN EN ISO 4042, thick-film passivated Niedax model no. : SAS38
Sales unit: 25 pieces
Lieske Part No.: 231268

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken to ensure that the connection thread of the push-through anchor does not protrude into the cable's terminal space, for fastening a cable or a metric pipe. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 16 x 79.5 mm Connection internal thread : M 6 for cable Ø : 38 - 47 mm for metric electrical installation pipes according to DIN EN 60423 : M 40 Material : Steel, galvanized according to DIN EN ISO 2081, thick-layer passivated Screw material : Steel, galvanized according to DIN EN ISO 4042, thick-layer passivated Niedax model no. : SAS 47
Sales unit: 20 pieces
Lieske Part No.: 207435

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable. For fastening a cable or a metric pipe. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 18 x 89 mm Internal connection thread : M 6 for cable Ø : 47 - 55 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 50 Material : Steel, galvanized in accordance with DIN EN ISO 2081, thick-film passivated Screw material : Steel, galvanized in accordance with DIN EN ISO 4042, thick-film passivated Niedax model no. : SAS55
Sales unit: 20 pieces
Lieske Part No.: 266879

Screw spacer clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21, when mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the terminal space of the cable, for fastening a cable or a metric pipe. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) W x L : 18 x 100 mm Internal connection thread : M 6 for cable Ø : 55 - 63 mm for metric electrical installation pipes in accordance with DIN EN 60423 : M 63 Material : Steel, galvanized in accordance with DIN EN ISO 2081, thick-film passivated Screw material : Steel, galvanized in accordance with DIN EN ISO 4042, thick-film passivated Niedax model no. : SAS60
Sales unit: 20 pieces
Lieske Part No.: 736666

Screw spacing clamp, with internal connection thread M 6, for cables and electrical installation pipes in accordance with DIN EN 61386-21. When mounting on push-through anchor DAM 6X... or screw anchor NSA 6X55/SW10-M6, care must be taken that the connection thread of the push-through anchor does not protrude into the cable's terminal space for fastening a cable. Please observe additional regulations for use in functional maintenance! Dimensions (approx. dimensions) W x L: 12 x 33 mm Internal connection thread: M 6 for cable Ø: 7.5 - 10 mm Material: Steel, galvanized in accordance with DIN EN ISO 2081, blue passivated Screw material: Steel, galvanized in accordance with DIN EN ISO 4042, blue passivated Niedax model no.: SAS 8 V
Sales unit: 50 pieces
Lieske Part No.: 1342452

Screw spacing clamp, heavy, for screwing on, with fastening hole. Can be used for: Machine installation pipe MI 60... Machine installation pipe MIG 60... Installation pipe connection MIA 60... Dimensions (approx. dimensions) Width W x Length L: 30 x 110 mm Fastening hole Ø: 9 mm for pipe Ø: 60 mm Material: Stainless steel, material no. 1.4301, 1.4303 Screw material: Stainless steel, material no. 1.4301, 1.4303 Niedax model no.: SASS 60 E3
Sales unit: 20 pieces
Lieske Part No.: 1327214

Collective holder, including nail dowel 6 x 50 mm, made of grey polyamide, halogen-free, for laying cable bundles on ceilings and walls. Plastics change their properties when exposed to temperature fluctuations, so the collective holders should be stored in a warmer environment below freezing before processing in order to fully guarantee the functionality of the upper mounting joint! Clear internal dimensions H x W: 105 x 45 mm
Sales unit: 25 pieces
Lieske Part No.: 894377

Collective holder, made of natural-colored polypropylene, contains halogens, flame-retardant according to VDE 0471-2-11-960° and UL 94-V2, for laying cable bundles on ceilings and walls. Plastics change their properties when exposed to temperature fluctuations, so the collective holders should be stored in a warmer environment below freezing before processing in order to fully guarantee the functionality of the upper mounting joint. Clear internal dimensions H x W: 70 x 30 mm
Sales unit: 50 pieces
Lieske Part No.: 617019

Collective holder, made of natural-colored polypropylene, contains halogen, flame-retardant according to VDE 0471-2-11-960° and UL 94-V2, for laying cable bundles on ceilings and walls. Plastics change their properties when exposed to temperature fluctuations, so the collective holders should be stored in a warmer environment below freezing before processing in order to fully guarantee the functionality of the upper mounting joint. Clear internal dimensions H x W: 105 x 45 mm
Sales unit: 25 pieces
Lieske Part No.: 555957

NIEDAX - Make: SHS 30
A holder from steel strip galvanized to DIN EN 10346, for the installation of cable bundles to the wall and ceiling, suitable for 30 cables (NYM 3x1.5 mmý). For use in the functional integrity please follow additional rules!

Clear internal dimensions H x W: 81 x 50 mm NIEDAX model no. SHS 30 Type: SHS30




Item: 100 ST.
Lieske Part No.: 286667

Collective holder with high mechanical strength for laying cable bundles on walls and ceilings. For use in functional maintenance or for suspended ceilings with fire protection requirements (model cable system guideline MLAR 2/2015), please observe additional regulations! Dimensions (approx. dimensions) clear internal dimensions H x W: 114.5 x 90 mm Material: steel, strip galvanized according to DIN EN 10346
Sales unit: 10 pieces
Lieske Part No.: 266486

Clamps 604
Steel, galvanized
Cable diameter: 3 mm

Type: 604 3MM
Item: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 244688

6 4 steel clamps, galvanized wire diameter: 4 mm Type: 6 4 4MM item:
ST.
Sales unit: 100 pieces
Lieske Part No.: 913011

Clamps 604
Steel, galvanized
Cable diameter: 5 mm Type: 604 5MM


Item: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 387227

Clamps 604
Steel, galvanized
Cable diameter: 6 mm

Type: 604 6MM
Item: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 214515

Clamps 6 4 galvanized steel cable diameter: 7 mm Type: 6 4 7MM Quantity:
ST.
Sales unit: 100 pieces
Lieske Part No.: 920338

Clamps 604
Steel, galvanized
Cable diameter: 8 mm

Type: 604 8MM
Item: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 427321

Clamps 604
Steel, galvanized
Cable diameter: 9 mm

Type: 604 9MM
Item: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 470519

Clamps 604
Steel, galvanized
Cable diameter: 10 mm

Type: 604 10MM
Item: 100 ST.
Lieske Part No.: 335982

604 clamps
, galvanized steel
cable diameter: 11 mm Type: 604 11MM


Item: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 691923

Clamps 6 4 galvanized steel cable diameter:
2 mm Type: 6 4
2mm Quantity:
ST.
Sales unit: 100 pieces
Lieske Part No.: 954605

604 clamps
, galvanized steel
cable diameter: 13 mm Type: 604 13MM


Item: 100 ST.
Sales unit: 100 pieces
Lieske Part No.: 612544