Installation Material from Scotch

Use the 3M Scotchlok UR-2 connector with its special insulation displacement contact to create a reliable electrical connection to wires in communication cables. The conductor is inserted into the U-contact connector, creating a spring-loaded connection. This removes the insulation and presses all conductors together with a firm, elastic pressure in one motion. The conductor insulation does not need to be removed. 3M Scotchlok connectors are factory filled with sealant that protects against corrosion and moisture. They are also available in a dry version for indoor use. Various sizes and wire combinations are available to meet all requirements. Solid wire size 0.4 mm to 0.9 mm with a maximum insulation diameter of 2.08 mm.
Sales unit: 100 pieces
Lieske Part No.: 695350

The 3M Scotchlok UR2-D-JA
R500, 0.4mm - 0.9mm single wire connector (dry), 500/can, can be used to connect two or three conductors with different conductor cross-sections. It is ideal for paper-insulated conductors. The UR2-D is an unfilled polypropylene connector for two copper wires with a diameter of 0.4 mm to 0.9 mm. Listed in the RUS list.
Lieske Part No.: 440492

Sales unit: 10 pieces
Lieske Part No.: 148535

3MT Cold Shrink Insulation Tubing 8420 and 8430 are EPDM tubing that is a unique cold shrink connection system. The products are supplied pre-stretched on a retractable support coil, allowing efficient and easy assembly. When the support coil is retracted after the tubing is positioned, the tubing shrinks to form a watertight seal. The active deformation of the specially formulated material ensures a permanent seal and insulation from the environment.
3MT Cold Shrink Insulation Tubing Series 8420 and 8430 are especially useful for electrical insulation on all solid dielectric (rubber or plastic) insulated wires and cable splices up to 1,000 V. They are suitable for indoor and outdoor use. They often provide good physical protection and environmental shielding for communication lines and other non-electrical applications (including cable jacket repairs). The operating temperature range is -40 °C to 90 °C. In applications where the product is continuously exposed to UV radiation, it should be wrapped with, for example, Scotch® Super 33+T Vinyl Insulation Tape or Scotch® Self-Vulcanizing Silicone Rubber Tape 70.
Sales unit: 10 pieces
Lieske Part No.: 218207

8420 and 8430 cold shrink insulation tubing is EPDM tubing that is a unique cold shrink connection system. The products are supplied pre-stretched on a retractable support coil, allowing efficient and easy assembly. When the support coil is retracted after the tubing is positioned, the tubing shrinks to form a watertight seal. The active deformation of the specially formulated material ensures a permanent seal and insulation from the environment.
8420 and 8430 series cold shrink insulation tubing is especially useful for electrical insulation on all solid dielectric (rubber or plastic) insulated wires and cable splices up to 1,000 V. They are suitable for indoor and outdoor use. They often provide good physical protection and environmental shielding on communication lines and other non-electrical applications (including cable jacket repairs). The temperature range is -40 °C to 90 °C. In applications where the product is continuously exposed to UV radiation, it should be wrapped with Super 33+T vinyl insulation tape or Self-vulcanizing silicone rubber tape 70, for example.
Sales unit: 10 pieces
Lieske Part No.: 876880

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Sales unit: 10 pieces
Lieske Part No.: 806668

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Sales unit: 10 pieces
Lieske Part No.: 323989

Heat-shrink compression connectors for electrically perfect connections and effective protection against moisture.
The 3MT ScotchlokT heat-shrink compression connectors can be used in installation technology wherever you want to connect single-wire conductors using compression technology. After heat-shrinking, the connectors also provide insulation that protects against moisture. This makes them particularly suitable for use in non-air-conditioned rooms or outdoors. The seamless connectors are made of tinned copper and are surrounded by an insulating layer of polyolefin with an inner coating of hot-melt adhesive. They can withstand a maximum voltage of 600 volts and their maximum operating temperature is 105 °C. The compression connectors are available in red, blue and yellow with a maximum conductor cross-section between 1.0 and 6.0 square millimeters. The maximum corresponds to the conductor cross-section. The ScotchlokT heat-shrink compression connectors are UL and CSA listed for use on flexible cables up to 600V.
Sales unit: 125 pieces
Lieske Part No.: 118268

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 846896

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 804885

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 496222

The cold shrink insulation tubes 8420 and 8430 are EPDM tubes that represent a unique cold shrink connection system. The products are supplied pre-stretched on a removable support coil, which enables efficient and easy installation. When the support coil is pulled out after positioning the tube, the tube shrinks and forms a watertight seal. The active deformation of the specially formulated material ensures permanent sealing and insulation from the environment.
Cold shrink tubes are used to insulate all plastic or rubber insulated cables. The products are supplied pre-stretched on a removable support coil, which enables efficient and easy installation. After assembly, the cold shrink tube provides reliable protection against moisture thanks to its constant radial contact pressure. Its good thermal stability and resistance to acids, alkalis, ozone and UV radiation guarantee long-lasting functionality.
Sales unit: 10 pieces
Lieske Part No.: 205992

Effective cable protection with the simplest application - the coaxial sealing kit does not require any tools for installation.
The 3MT cold shrink coaxial cable sealing kit 98-KC reliably protects coaxial connectors and antenna entries indoors and outdoors from moisture. It is especially suitable for applications with mobile phone antennas and base stations. The cold shrink kit also ensures flexible kink protection. Its simple and quick installation by pulling out the support spiral enables reliable installation even without special tools, such as shrink burners. After installation, the cold shrink tubing provides reliable protection against moisture thanks to its constant radial contact pressure. Its very good thermal stability and resistance to acids, alkalis, ozone and UV radiation guarantee long-lasting functionality.
Sales unit: 10 pieces
Lieske Part No.: 911975

8420 and 8430 cold shrink insulation tubing is EPDM tubing that is a unique cold shrink connection system. The products are supplied pre-stretched on a retractable support coil, allowing efficient and easy assembly. When the support coil is retracted after the tubing is positioned, the tubing shrinks to form a watertight seal. The active deformation of the specially formulated material ensures a permanent seal and insulation from the environment.
8420 and 8430 series cold shrink insulation tubing is especially useful for electrical insulation on all solid dielectric (rubber or plastic) insulated wires and cable splices up to 1,000 V. They are suitable for indoor and outdoor use. They often provide good physical protection and environmental shielding on communication lines and other non-electrical applications (including cable jacket repairs). The temperature range is -40 °C to 90 °C. In applications where the product is continuously exposed to UV radiation, it should be wrapped with Super 33+T vinyl insulation tape or Self-vulcanizing silicone rubber tape 70, for example.
Sales unit: 10 pieces
Lieske Part No.: 689075

8420 and 8430 cold shrink insulation tubing is EPDM tubing that is a unique cold shrink connection system. The products are supplied pre-stretched on a retractable support coil, allowing efficient and easy assembly. When the support coil is retracted after the tubing is positioned, the tubing shrinks to form a watertight seal. The active deformation of the specially formulated material ensures a permanent seal and insulation from the environment.
8420 and 8430 series cold shrink insulation tubing is especially useful for electrical insulation on all solid dielectric (rubber or plastic) insulated wires and cable splices up to 1,000 V. They are suitable for indoor and outdoor use. They often provide good physical protection and environmental shielding on communication lines and other non-electrical applications (including cable jacket repairs). The temperature range is -40 °C to 90 °C. In applications where the product is continuously exposed to UV radiation, it should be wrapped with Super 33+T vinyl insulation tape or Self-vulcanizing silicone rubber tape 70, for example.
Sales unit: 10 pieces
Lieske Part No.: 150533

3M QTII Cold Shrink Outdoor Cable Termination, 1 Conductor
The 3MT Cold Shrink Cable Termination Kit, 5620K Series, is designed for terminating medium voltage solid dielectric insulated cables in indoor applications. When the core of the cable termination is unwound, it shrinks over the cable, ensuring a perfect, leak-proof fit. The cable termination's tracking-resistant silicone rubber insulation ensures long service life. Approved for weatherproof applications.
Lieske Part No.: 306467

3M QTII Cold Shrink Outdoor Cable Termination, 1 Conductor
The 3MT Cold Shrink Cable Termination Kit, 5620K Series, is designed for terminating medium voltage solid dielectric insulated cables in indoor applications. When the core of the cable termination is unwound, it shrinks over the cable, ensuring a perfect, leak-proof fit. The cable termination's tracking-resistant silicone rubber insulation ensures long service life. Approved for weatherproof applications.
Lieske Part No.: 185673

Casting resin 40 is a two-component polyurethane resin for general applications that hardens at room temperature. It is supplied in a two-component plastic bag in the correct stoichiometric ratio by tearing open a separating seam.
Casting resin 40 is suitable for electrical insulation and mechanical protection of electrical connections for use up to 1 kV. The water-repellent polyurethane resin meets the requirements of CENELEC HD631.1 S2 and is compliant with EU Directive 2011/65/EC (RoHS) and EU Directive 1907/2007/EC (REACH). It guarantees the highest level of electrical insulation for professional use. Fast and clean application thanks to the new 3M patented integrated casting nozzle in the resin bag. Bag opener is included.
Sales unit: 10 pieces
Lieske Part No.: 413305

The premium resin cable joint kits contain cable resin 40, a high-quality, two-component polyurethane compound developed for general electrical insulation, moisture sealing and mechanical protection.
The 92-NBA series cast resin joint kit is designed for one to five-core, unshielded low-voltage plastic cables. It ensures electrical insulation and mechanical protection of cable joints. The SVHC-free premium joint kit, tested according to EN 50393, can be used indoors and outdoors, underground or underwater. The transparent, one-piece casting shell can be folded up in no time at all and closes by automatically snapping into place. Pre-formed, perforated foam seals are also used. This eliminates the previously time-consuming use of saws and adhesive tape for a tight seal. A GMG system (closed mixing and pouring) is used when casting the cast resin 40 included in the scope of delivery. This means that contact with the casting resin during processing is practically impossible. The transparent mixing bag guarantees visual control of the mixing process. After use, the mixing bag with the remaining hardened casting resin can be disposed of as normal household waste. Disposal as hazardous waste is not necessary.
Sales unit: 10 pieces
Lieske Part No.: 555341

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 25 pieces
Lieske Part No.: 882443

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 15 pieces
Lieske Part No.: 543870

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 15 pieces
Lieske Part No.: 760098

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 15 pieces
Lieske Part No.: 342227

Heat Shrink Tubing GTI is a flexible RoHS heat shrink tubing range. The tubes have a flame retardant wall made of cross-linked polyolefin. They provide reliable performance for electrical splices, joints and connections up to 600V. GTI heat shrink tubing is available in many different colors and sizes with a shrink ratio of 2:1. This GTI heat shrink tubing kit comes in a convenient sorting box (size 270mm x 160mm x 60mm).
Heat shrink tubing GTI is color coded for quick and easy wire identification. This split-resistant, flame retardant tubing is used as a shrink fit as well as electrical insulation over cable splices or terminations. The tubing with a 2:1 expansion ratio is mechanically tough, easily markable and resists cold flow. The tubing is ideal for lightweight harness covering, fire resistant covering, cable marking, cable bundling and component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 4 pieces
Lieske Part No.: 329876

3MT Heat Shrink Tubing GTI is a RoHS flexible heat shrink tubing range. The tubes have a flame retardant wall made of cross-linked polyolefin. They provide reliable performance for electrical splices, joints and connections up to 600V. GTI heat shrink tubing is available in many different colors and sizes with a shrink ratio of 2:1. This GTI heat shrink tubing kit is supplied in a convenient sorting box (size 270mm x 160mm x 60mm).
3MT Heat Shrink Tubing GTI is color coded for quick and easy wire identification. This split-resistant, flame retardant tubing is used as a shrink fit as well as electrical insulation over cable splices or terminations. The tubing with a 2:1 expansion ratio is mechanically tough, easily markable and resists cold flow. The tubing is ideal for lightweight harness covering, fire resistant covering, cable marking, cable bundling and component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 4 pieces
Lieske Part No.: 335098

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 20 pieces
Lieske Part No.: 313372

GTI-3000 tubing is co-extruded and features an inner seal. The inner seal securely seals complex parts while the outer wall provides good mechanical protection. The GTI-A 3000 has a shrink ratio of 3:1. The GTI-A 3000 heat
shrink tubing is split resistant, features an inner seal and is used as a shrink fit or electrical insulation over cable splices or terminations. The tubing with an expansion ratio of 3:1 is mechanically robust, easily markable and resists cold flow. Temperature resistant from -55 to 135 °C.
Sales unit: 10 pieces
Lieske Part No.: 110003

GTI-3000 tubing is co-extruded and features an inner seal. The inner seal securely seals complex parts while the outer wall provides good mechanical protection. The GTI-A 3000 has a shrink ratio of 3:1. The GTI-A 3000 heat
shrink tubing is split resistant, features an inner seal and is used as a shrink fit or electrical insulation over cable splices or terminations. The tubing with an expansion ratio of 3:1 is mechanically robust, easily markable and resists cold flow. Temperature resistant from -55 to 135 °C.
Sales unit: 20 pieces
Lieske Part No.: 139126

8420 and 8430 cold shrink insulation tubing is EPDM tubing that is a unique cold shrink connection system. The products are supplied pre-stretched on a retractable support coil, allowing efficient and easy assembly. When the support coil is retracted after the tubing is positioned, the tubing shrinks to form a watertight seal. The active deformation of the specially formulated material ensures a permanent seal and insulation from the environment.
8420 and 8430 series cold shrink insulation tubing is especially useful for electrical insulation on all solid dielectric (rubber or plastic) insulated wires and cable splices up to 1,000 V. They are suitable for indoor and outdoor use. They often provide good physical protection and environmental shielding on communication lines and other non-electrical applications (including cable jacket repairs). The temperature range is -40 °C to 90 °C. In applications where the product is continuously exposed to UV radiation, it should be wrapped with Super 33+T vinyl insulation tape or Self-vulcanizing silicone rubber tape 70, for example.
Sales unit: 10 pieces
Lieske Part No.: 339132

The MGO flexible magnetic tape is 1.55 mm thick and has a pressure-sensitive rubber adhesive.
Thanks to the high-performance adhesive on one of its sides, the MGO magnetic tape ensures the fixation, whether removable or not, of numerous supports. It is easy to attach, lift off, remove, store and reuse.
Sales unit: 5 pieces
Lieske Part No.: 313228

The STD Wire Marker Dispenser is a compact, convenient marking solution - available with pre-loaded number or color printed labels. This wire marker dispenser has 10 refillable compartments and comes complete with a full refill lead.
The wire marker dispenser features flip-top lids that allow you to peel and tear off precise lengths. This dispenser is pre-loaded with sharp, easy-to-read pre-printed numbers (0-9). It has 10 refillable compartments - each dispenser comes complete with a full refill lead.
Made from durable plastic, the dispenser protects wire markers from contamination and keeps them clean and dry. Its compact design fits conveniently in a pocket or toolbox - or can be hung from a tool bag or strap.
Lieske Part No.: 972546

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Sales unit: 10 pieces
Lieske Part No.: 531503

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Lieske Part No.: 907778

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Lieske Part No.: 556542

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Sales unit: 10 pieces
Lieske Part No.: 558195

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Sales unit: 10 pieces
Lieske Part No.: 287164

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Sales unit: 10 pieces
Lieske Part No.: 584647

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Sales unit: 10 pieces
Lieske Part No.: 225104

Cable marking tape SDR is available as a refill roll for the STD cable marker dispenser as individual numbers, letters or symbols.
Use the cable marking tape refill roll to easily identify terminal blocks, strips, panel wires or switchgear for maintenance and repair. This thin, conformable tape is printed with easy-to-read characters. Made from polyester, the tape is resistant to tarnish, oil, solvents and water. Ideal for phase identification on large or small wires/cables, hoses and spare parts. It is compatible with STD cable markers, which allow for quick and easy use.
Sales unit: 10 pieces
Lieske Part No.: 392539

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 959528

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 523781

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 284574

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard pack as standard.
Sales unit: 100 pieces
Lieske Part No.: 155905

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard packs as standard.
Lieske Part No.: 320995

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard packs as standard.
Sales unit: 10 pieces
Lieske Part No.: 490004

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard pack as standard.
Lieske Part No.: 754316

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard packs as standard.
Sales unit: 5 pieces
Lieske Part No.: 256486

Heat shrink cable branch sleeves are used to insulate and seal cable breaks in multi-core armored or jacketed cables. This robust sleeve offers good electrical and mechanical protection. The cross-linked polyolefin construction, approved to MIL-I-81765/1, is semi-rigid and flame retardant.
The heat shrink cable branch sleeve has an internal adhesive coating that ensures reliable cable break sealing against environmental influences in cables and conductor ends. RoHS 2011/65/EU compliant.
Sales unit: 3 pieces
Lieske Part No.: 646632

Heat shrink cable branch sleeves are used to insulate and seal cable breaks in multi-core armored or jacketed cables. This robust sleeve offers good electrical and mechanical protection. The cross-linked polyolefin construction, approved to MIL-I-81765/1, is semi-rigid and flame retardant.
The heat shrink cable branch sleeve has an internal adhesive coating that ensures reliable cable break sealing against environmental influences in cables and conductor ends. RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 574248

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard packs as standard.
Lieske Part No.: 951179