Link chain, according to DIN 763, for suspensions. The load-bearing capacity information only applies if the chain is sufficiently anchored to the supporting surface. Dimensions (approx. dimensions) Inner chain link dimension H: 22 mm Outer chain link dimension B: 8 mm Material thickness t: 2 mm Load-bearing capacity F: 0.5 kN Delivery length L: 50 m Material: Stainless steel, material no. 1.4401, 1.4404
Sales unit: 50 meters
Lieske Part No.: 577743

Link chain, according to DIN 763, for suspensions. The load-bearing capacity information only applies if the chain is sufficiently anchored to the supporting surface. Dimensions (approx. dimensions) Inner chain link dimension H: 26 mm Outer chain link dimension B: 12 mm Material thickness t: 3 mm Load-bearing capacity F: 1.2 kN Delivery length L: 50 m Material: Stainless steel, material no. 1.4401, 1.4404
Sales unit: 50 meters
Lieske Part No.: 1315972

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 60 - 64 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 25 pieces
Lieske Part No.: 1315988

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 26 - 30 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 50 pieces
Lieske Part No.: 1315971

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 32 - 36 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 50 pieces
Lieske Part No.: 460741

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 38 - 43 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 25 pieces
Lieske Part No.: 460744

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 68 - 72 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 25 pieces
Lieske Part No.: 1315970

E-clips, pipe clamp with rubber insert, two-part, with threaded connection for both thread sizes, for threaded rod suspension. Dimensions (approx. dimensions) for pipe Ø: 99 - 105 mm for threaded connection: M 8 / M 10 Pipe clamp material: steel, galvanized/chromated according to DIN 50021 Rubber insert material: TPE (thermoplastic elastomers)
Sales unit: 25 pieces
Lieske Part No.: 1315969

Profile clamp including M 8 stud screw with slotted hexagon head and clamping plate, for clamping to support profiles with parallel flanges or with slanted flanges up to a maximum of 14% inclination and as a supply line to the energy consumers. The fastening materials used can vary depending on the application! Dimensions (approx. dimensions) H x W x L: 57 x 40 x 47 mm Threaded connections: M 6 Load capacity specification vertical nominal load F1: 1.8 kN Load capacity specification vertical nominal load F2: 1.6 kN Flange thickness of the support t: 6 - 35 mm Screw tightening torque: 4 Nm Wrench size: SW 13 Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Sales unit: 25 pieces
Lieske Part No.: 1344802

Profile clamp including M 8 stud screw with slotted hexagon head and clamping plate, for clamping to support profiles with parallel flanges or with slanted flanges up to a maximum of 14% inclination and as a supply line to the energy consumers. The fastening materials used can vary depending on the application! Dimensions (approx. dimensions) H x W x L: 57 x 40 x 47 mm Threaded connections: M 8 Load capacity specification vertical nominal load F1: 1.8 kN Load capacity specification vertical nominal load F2: 1.6 kN Flange thickness of the support t: 6 - 35 mm Screw tightening torque: 4 Nm Wrench size: SW 13 Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 25 pieces
Lieske Part No.: 1345238

Profile clamp including M 8 stud screw with slotted hexagon head and clamping plate, for clamping to support profiles with parallel flanges or with slanted flanges up to a maximum of 14% inclination and as a supply line to the energy consumers. The fastening materials used can vary depending on the application! Dimensions (approx. dimensions) H x W x L: 57 x 40 x 47 mm Threaded connections: M 8 Load capacity specification vertical nominal load F1: 1.8 kN Load capacity specification vertical nominal load F2: 1.6 kN Flange thickness of the support t: 6 - 35 mm Screw tightening torque: 4 Nm Wrench size: SW 13 Material: Steel, hot-dip galvanized in accordance with DIN EN ISO 1461
Sales unit: 25 pieces
Lieske Part No.: 185134

S-hook for link chain: KG... KF... KN... Dimensions (approx. dimensions) H: 45 mm Material thickness t: 5 mm Load capacity F: 0.3 kN Material: Steel, galvanized/chromated according to DIN 50021
Sales unit: 100 pieces
Lieske Part No.: 912685

S-hook for link chain: KG... KF... KN... Dimensions (approx. dimensions) H: 35 mm Material thickness: 4 mm Material: stainless steel, material no. 1.4401, 1.4404
Sales unit: 100 pieces
Lieske Part No.: 147906

E-clips, screw clamp with joint, for screwing onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 1 - 25 mm Width W x Height H (without joint): 60 x 71 mm Distance from screw clamp inside to clamping screw C: 12 mm Side fastening holes: 2 x Ø 10 mm Joint thread connection: M 10 Load capacity F: 2 kN Material: Steel, mechanically galvanized/passivated in accordance with DIN EN ISO 9227
Sales unit: 10 pieces
Lieske Part No.: 210728

E-clips, screw clamp, for screwing onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 15 - 33 mm Width B: 60 mm for threaded rod through hole: Ø 14 mm Load capacity F: 1.1 kN Material: Steel, rustproof, material no. 1.4401
Sales unit: 25 pieces
Lieske Part No.: 204998

Steigetrassenbefestigungsadapter für die Decken- und Bodenbefestigung von Steigetrassen (STL 60. ... und STM 60. ...) inkl. Zubehör (FLM 8X16 F). Zur Verwendung bei vertikalen Kabelführungen im integrierten Funktionserhalt. Für den Aussenbereich empfiehlt sich die Edelstahlvarianten. Die Steigetrassen werden mittels der Steigetrassenbefestigungsadapter in 'Fest- bzw. Loslageranordnung' installiert. Beachtet werden muss die brandschutztechnische Beurteilung der Fa. Niedax. Durchsteckanker DAZ... zur Boden- / Deckenbefestigung müssen gesondert bestellt werden. Abstand zwischen Decke und Boden : = 3,5 m für Steigetrassen : STL 60. ... F / STM 60. ... F Max. Nennbreite bei : Steigetrassen STL 60. ... B = 400 mm Steigetrassen STM 60. ... B = 600 mm Abmessungen (ca. Maße) H x B x L : 91 x 152 x 70 mm Materialstärke t : 3 mm Werkstoff : Stahl, tauchfeuerverzinkt nach DIN EN ISO 1461
Sales unit: 20 pieces
Lieske Part No.: 832944

Beam intermediate clamps, including hexagon screws with shoulder tip in accordance with DIN 564, for clamping the rail between the legs of a T-beam. The specified load capacity refers to a leg spacing of 400 mm and an applied torque of 2.5 Nm with exclusively vertical load introduction. If larger leg spacings are used, the max. load capacity must be reduced. Please order the rail separately (the length corresponds to the distance between the two flanges) and cut to length on site (minus approx. 16 mm material thickness and screw tip), mount with the two beam intermediate clamps and then position and clamp in the beam. for anchor rail: 2986 2996Z Accessories: 4 x SK 8X25 V Dimensions (approx. dimensions) H x W x L: 15 x 45.5 x 100 mm Material thickness t: 2 mm Load capacity F: 0.5 kN Leg spacing/2 Material intermediate clamp: Steel, strip galvanized according to DIN EN 10346 Material hexagon screw: Steel, electrogalvanized according to DIN EN ISO 4042, blue passivated Niedax model no.: TZK 86-96 S
Lieske Part No.: 273110

E-clips, screw clamp, for screwing onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 10 - 21 mm Width B: 47 mm for threaded rod through hole: Ø 14 mm Load capacity F: 1.1 kN Material: steel, hot-dip galvanized
Sales unit: 100 pieces
Lieske Part No.: 1315697

Mounting bracket with 3 holes for cross-shaped connection of profile rails 41 x 21 mm.
Sales unit: 10 pieces
Lieske Part No.: 578502

Mounting bracket with 3 holes for cross-shaped connection of profile rails 41 x 41 mm.
Lieske Part No.: 305674

Mounting bracket with 3 holes for cross-shaped connection of professional rails 41 x 21 mm.
Sales unit: 10 pieces
Lieske Part No.: 580749

Mounting bracket with 3 holes for cross-shaped connection of profile rails 41 x 41 mm.
Sales unit: 10 pieces
Lieske Part No.: 1330390

With through hole.
Max. tightening torque: 8 Nm
Sales unit: 50 pieces
Lieske Part No.: 789822

With thread.
Max. tightening torque: 8 Nm
Sales unit: 50 pieces
Lieske Part No.: 734879

With thread.
Max. tightening torque: 18 Nm
Lieske Part No.: 140893

With thread.
Max. tightening torque: 21 Nm
Sales unit: 25 pieces
Lieske Part No.: 795616

For suspending light supports or other components.
Sales unit: 25 meters
Lieske Part No.: 265330

Beam clamp for mounting pipes. Closed pipe holder at the bottom. Fastened to steel beams by hammering.
Sales unit: 50 pieces
Lieske Part No.: 2121901

Beam clamp for mounting pipes. Closed pipe holder at the bottom. Fastened to steel beams by hammering.
Sales unit: 50 pieces
Lieske Part No.: 1103519

Beam clamp for mounting pipes. Closed pipe holder at the bottom. Fastened to steel beams by hammering.
Sales unit: 50 pieces
Lieske Part No.: 2128774

Mounting brackets for attaching poles, ladders and structures to walls, ceilings or steel scaffolding.
Sales unit: 10 pieces
Lieske Part No.: 2069894

Mounting brackets for attaching poles, ladders and structures to walls, ceilings or steel scaffolding.
Sales unit: 10 pieces
Lieske Part No.: 2069895

Mounting brackets for attaching poles, ladders and structures to walls, ceilings or steel scaffolding.
Sales unit: 10 pieces
Lieske Part No.: 2069896

Mounting brackets for attaching poles, ladders and structures to walls, ceilings or steel scaffolding.
Sales unit: 10 pieces
Lieske Part No.: 2069897

Mounting brackets for attaching poles, ladders and structures to walls, ceilings or steel scaffolding.
Sales unit: 10 pieces
Lieske Part No.: 2069898

Mounting brackets for attaching poles, ladders and structures to walls, ceilings or steel scaffolding.
Sales unit: 10 pieces
Lieske Part No.: 2069899

Mounting brackets for creating individual supporting structures with U-posts.
Lieske Part No.: 1055267

Mounting brackets for creating individual supporting structures with U-posts.
Sales unit: 5 pieces
Lieske Part No.: 1100923

Mounting bracket in lightweight design with side dimensions 64 x 32 mm.
Sales unit: 10 pieces
Lieske Part No.: 664861

Protective cap for the end cover of US 3 stems.
Lieske Part No.: 195684

Spacer for use in trapezoidal profiles type TP.
Sales unit: 10 pieces
Lieske Part No.: 169018

Clamping bracket individually as a spare part for attaching the boom AS 30 or AS 55 to the hanging support IS 8.
Lieske Part No.: 327701

Ecopack 31Wire suspension
Lieske Part No.: 676994

Round 21Seilabhängung
Lieske Part No.: 842299

LicrossRope suspension
Lieske Part No.: 673127

LicrossRope suspension
Lieske Part No.: 673129