Heat-shrink wall feedthrough for permanently gas- and watertight cable entries into the building.
The 3MT heat-shrink wall feedthrough WMD is used to seal telecommunications and power cables in wall feedthroughs. It enables gas- and watertight introduction of cables and pipes into the building. The cables or pipes can also be pulled in at a later date and installation as a reserve feedthrough is also possible. The wavy surface of the wall feedthrough is coated with a special sealing material. This allows you to achieve a permanently waterproof seal when closing the breakthrough opening with mortar or cement. The scope of delivery consists of a polyolefin shrink tube shrunk onto a support spiral, a cable cleaning cloth and the assembly instructions.
Sales unit: 5 pieces
Lieske Part No.: 914517

Safe and easy to install - the heat-shrink telecommunications set with temperature indicator.
The 3MT heat-shrink telecommunications connection and branch set FVAM is suitable for all filled and unfilled telecommunications and signal cables without compressed air monitoring. The set complies with the 'Technical Delivery Conditions of Deutsche Telekom AG'. The protective insert supplied serves as a water vapor barrier and to protect the cable splice from excessive heat and for mechanical protection. A coating with temperature indicator paint on the outside of the sleeve indicates the end of the shrinking process by changing color. A rust-proof locking rail prevents the sleeve from opening or warping during shrinking. The scope of delivery of the connection and branch set includes a heat-shrink sleeve with temperature indicator paint, locking rail, protective insert, shield connector and connection cable, cable cleaning cloth, emery cloth and assembly instructions. A branch system is not included in the scope of delivery.
Sales unit: 3 pieces
Lieske Part No.: 837647

Heat-shrink wall feedthrough for permanently gas- and watertight cable entries into the building.
The 3MT heat-shrink wall feedthrough WMD is used to seal telecommunications and power cables in wall feedthroughs. It enables gas- and watertight introduction of cables and pipes into the building. The cables or pipes can also be pulled in at a later date and installation as a reserve feedthrough is also possible. The wavy surface of the wall feedthrough is coated with a special sealing material. This allows you to achieve a permanently waterproof seal when closing the breakthrough opening with mortar or cement. The scope of delivery consists of a polyolefin shrink tube shrunk onto a support spiral, a cable cleaning cloth and the assembly instructions.
Sales unit: 5 pieces
Lieske Part No.: 843616

3M QTII Cold Shrink Outdoor Cable Terminator, 1 Conductor
The 5620K Series Cold Shrink Outdoor Cable Terminator Kit is designed for terminating medium voltage solid dielectric insulated cables in indoor applications. When the core of the cable termination is unwound, it shrinks over the cable, providing a perfect, leak-proof fit. The cable termination's tracking-resistant silicone rubber insulation ensures long service life. Approved for weatherproof applications.
Lieske Part No.: 829462

3M QTII Cold Shrink Outdoor Cable Termination, 1 Conductor
The 3MT Cold Shrink Cable Termination Kit, 5620K Series, is designed for terminating medium voltage solid dielectric insulated cables in indoor applications. When the core of the cable termination is unwound, it shrinks over the cable, ensuring a perfect, leak-proof fit. The cable termination's tracking-resistant silicone rubber insulation ensures long service life. Approved for weatherproof applications.
Sales unit: 4 pieces
Lieske Part No.: 495816

Flame-retardant casting resin that impresses with its very good chemical resistance. The casting resin is hydrophobic and can therefore harden in water.
3MT ScotchcastT 1402FR polyurethane resin in a bag is suitable as electrical insulation and mechanical protection of electrical connections for use up to 1 kV. It meets the requirements of CENELEC HD631.1 S2 and is compliant with EU Directive 2002/95/EC (RoHS) and EU Directive 1907/2007/EC (REACH) and guarantees the highest level of electrical insulation for professional use. Fast and clean application is possible thanks to the new, patented 3MT filler neck integrated into the resin bag. Bag opener is included in delivery.
Sales unit: 10 pieces
Lieske Part No.: 542632

The 3MT ScotchcastT Premium Resin Cable Joint Kits contain ScotchcastT Cable Resin 40, a high-quality, two-component polyurethane compound developed for general electrical insulation, moisture sealing and mechanical protection.
The 3MT ScotchcastT Cast Resin Joint Kit of the 92-NBA series is designed for one to five-core, unshielded low-voltage plastic cables. It ensures electrical insulation and mechanical protection of cable joints. The SVHC-free, premium joint kit, tested according to EN 50393, can be used indoors and outdoors, underground or underwater. The transparent, one-piece potting shell can be folded up in an instant and closes with an automatic snap-in. Pre-formed, perforated foam seals are also used. This eliminates the previously time-consuming use of a saw and adhesive tape for a tight seal. A GMG system (closed mixing and pouring) is used when casting the 3MT ScotchcastT casting resin 40 included in the delivery. This means that contact with the casting resin during processing is practically impossible. The transparent mixing bag guarantees visual control of the mixing process. After use, the mixing bag with the remaining hardened casting resin can be disposed of as normal household waste. Disposal as hazardous waste is not necessary.
Sales unit: 10 pieces
Lieske Part No.: 765652

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 10 pieces
Lieske Part No.: 759118

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 452899

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 418840

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 135290

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 904828

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 930750

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 942183

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 10 pieces
Lieske Part No.: 505825

HSR-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing
made from cross-linked halogen-free polyolefin. HSR 3000 provides good insulation protection in various industrial
applications. It is also suitable for cable marking and identification applications. HSR 3000
tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
HSR-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant, halogen-free tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 861734

HSR-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing
made from cross-linked halogen-free polyolefin. HSR 3000 provides good insulation protection in various industrial
applications. It is also suitable for cable marking and identification applications. HSR 3000
tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
HSR-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant, halogen-free tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 977651

HSR-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing
made from cross-linked halogen-free polyolefin. HSR 3000 provides good insulation protection in various industrial
applications. It is also suitable for cable marking and identification applications. HSR 3000
tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
HSR-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant, halogen-free tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 844704

HSR-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing
made from cross-linked halogen-free polyolefin. HSR 3000 provides good insulation protection in various industrial
applications. It is also suitable for cable marking and identification applications. HSR 3000
tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
HSR-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant, halogen-free tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 342666

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 20 pieces
Lieske Part No.: 354941

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 10 pieces
Lieske Part No.: 384408

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 978748

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 751569

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 247799

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 2 pieces
Lieske Part No.: 845497

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 2 pieces
Lieske Part No.: 201753

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Lieske Part No.: 622436

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 20 pieces
Lieske Part No.: 271131

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 20 pieces
Lieske Part No.: 988142

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 10 pieces
Lieske Part No.: 234099

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 3 pieces
Lieske Part No.: 972763

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 3 pieces
Lieske Part No.: 734621

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 2 pieces
Lieske Part No.: 673181

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Lieske Part No.: 336012

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Lieske Part No.: 492703

The 3MT 91-AH is a heat shrink connection kit for crimp connectors designed for low voltages. It is suitable for 4 or 5 core, unshielded and unarmored insulated low voltage plastic cables up to 0.6/1 kV (according to HD 603 and IEC 60502-1). The cable cross section range is 5 x 1.5 to 5 x 6 mm². RoHS compliant, halogen free. Good electrical insulation and resistance to moisture, mechanical stress, chemicals and UV radiation.
The 3MT 91-AH is a heat shrink connection kit for crimp connectors designed for low voltages. It is suitable for 4 or 5 core, unshielded and unarmored insulated low voltage plastic cables up to 0.6/1 kV (according to HD 603 and IEC 60502-1). Shrink ratio of up to 4.5:1, minimum shrink temperature of 135 °C, operating temperature range of -55 °C to 130 °C. The 91-AH 20-5N is RoHS compliant, halogen free and offers excellent waterproof moisture sealing and protection against mechanical impacts. It has outstanding electrical insulation and good resistance to UV radiation, alkaline earths and chemicals. Applications include electrical insulation and mechanical protection of crimp connectors. The 91-AH is suitable for indoor and outdoor use in underground and underwater installations. 91-AH is available in black color and in sizes designed for a cable cross-section range of 5 x 1.5 to 5 x 6 mm². Standard packaging as a set. Approvals: Type tested according to DIN EN 50393, Table 3
Sales unit: 3 pieces
Lieske Part No.: 810903

The EC Series cold shrink cable end caps are closed tubular rubber sleeves that are pre-stretched at the factory and fitted with a removable support coil. When positioned over the end of a cable, pipe or other cylindrical object, the support coil is pulled out, creating a reliable seal against environmental influences. Four different end caps are available to accommodate a wide range of diameters (from 11.7 mm to 84.3 mm).
The EC Series cold shrink cable end caps have good resistance to abrasion, water, fungi, acids, alkalis and ozone, ensuring a long service life. Installation does not require any tools or adhesive tape/mastic.
Sales unit: 10 pieces
Lieske Part No.: 783436

8420 and 8430 cold shrink insulation tubing is EPDM tubing that is a unique cold shrink connection system. The products are supplied pre-stretched on a retractable support coil, allowing efficient and easy assembly. When the support coil is retracted after the tubing is positioned, the tubing shrinks to form a watertight seal. The active deformation of the specially formulated material ensures a permanent seal and insulation from the environment.
8420 and 8430 series cold shrink insulation tubing is especially useful for electrical insulation on all solid dielectric (rubber or plastic) insulated wires and cable splices up to 1,000 V. They are suitable for indoor and outdoor use. They often provide good physical protection and environmental shielding on communication lines and other non-electrical applications (including cable jacket repairs). The temperature range is -40 °C to 90 °C. In applications where the product is continuously exposed to UV radiation, it should be wrapped with Super 33+T vinyl insulation tape or Self-vulcanizing silicone rubber tape 70, for example.
Sales unit: 10 pieces
Lieske Part No.: 393451

The 3MT 91-AH is a heat shrink connection set for crimp connectors designed for low voltages. It is suitable for 4- or 5-core, unshielded and unarmored insulated low-voltage plastic cables with up to 0.6/1 kV (according to HD 603 and IEC 60502-1). The cable cross-section range is 5 x 1.5 to 5 x 6 mm². RoHS compliant, halogen-free. Good electrical insulation and resistance to moisture, mechanical stress, chemicals and UV radiation.
The 3MT heat shrink connection set of the 91-AHSC series with screw connectors enables a simple, quick and secure cable connection and is suitable for all common plastic cables with PVC or XLPE insulation in low voltage. You can use it both indoors and outdoors and for underground installation. Due to its high shrinkage rate, it covers a large cross-section range, which is why only a few sizes are needed for a large number of connections. The connection set is extremely resistant to aging and chemicals and has very good mechanical strength. A set contains a thick-walled outer tube, four or five inner tubes, the same number of screw connectors, a hexagon wrench and emery cloth. The screw connectors are suitable for copper and aluminum conductors and do not require any special tools.
Lieske Part No.: 643982

Heat shrink tubing made of self-extinguishing polyolefin with hot melt adhesive coating. For ageing, UV and moisture resistant insulation of plastic and ground cables and as an outer tube for control cable sets. The diameter before shrinking is 19 mm and after shrinking 6 mm.
Lieske Part No.: 588102

Shrink sleeve Pliofine SAM 1.6
Sales unit: 150 meters
Lieske Part No.: 458980

Shrink sleeve Pliofine SAM 1.6 (1.22m)
Lieske Part No.: 458986

Shrink sleeve Pliofine SAM 6.4
Sales unit: 75 meters
Lieske Part No.: 458995

Shrink sleeve Pliofine SAM 9.5
Sales unit: 75 meters
Lieske Part No.: 459021

Shrink sleeve Pliofine SAM 12.7
Sales unit: 50 meters
Lieske Part No.: 459047

Shrink sleeve Pliofine SAM 16.0
Sales unit: 50 meters
Lieske Part No.: 459050

Shrink wrap Pliofine SAM 32.0 (1.22m)
Lieske Part No.: 459060

Shrink tube Pliofine SAM 1.6 Box (17m)
Lieske Part No.: 459073

Shrink tube Pliofine SAM 2.4 Box (15m)
Lieske Part No.: 459078

Shrink tube Pliofine SAM 3.2 Box (15m)
Lieske Part No.: 459083