3M QTII Cold Shrink Outdoor Cable Termination, 1 Conductor
The 3MT Cold Shrink Cable Termination Kit, 5620K Series, is designed for terminating medium voltage solid dielectric insulated cables in indoor applications. When the core of the cable termination is unwound, it shrinks over the cable, ensuring a perfect, leak-proof fit. The cable termination's tracking-resistant silicone rubber insulation ensures long service life. Approved for weatherproof applications.
Lieske Part No.: 306467

3M QTII Cold Shrink Outdoor Cable Termination, 1 Conductor
The 3MT Cold Shrink Cable Termination Kit, 5620K Series, is designed for terminating medium voltage solid dielectric insulated cables in indoor applications. When the core of the cable termination is unwound, it shrinks over the cable, ensuring a perfect, leak-proof fit. The cable termination's tracking-resistant silicone rubber insulation ensures long service life. Approved for weatherproof applications.
Lieske Part No.: 185673

Casting resin 40 is a two-component polyurethane resin for general applications that hardens at room temperature. It is supplied in a two-component plastic bag in the correct stoichiometric ratio by tearing open a separating seam.
Casting resin 40 is suitable for electrical insulation and mechanical protection of electrical connections for use up to 1 kV. The water-repellent polyurethane resin meets the requirements of CENELEC HD631.1 S2 and is compliant with EU Directive 2011/65/EC (RoHS) and EU Directive 1907/2007/EC (REACH). It guarantees the highest level of electrical insulation for professional use. Fast and clean application thanks to the new 3M patented integrated casting nozzle in the resin bag. Bag opener is included.
Sales unit: 10 pieces
Lieske Part No.: 413305

The premium resin cable joint kits contain cable resin 40, a high-quality, two-component polyurethane compound developed for general electrical insulation, moisture sealing and mechanical protection.
The 92-NBA series cast resin joint kit is designed for one to five-core, unshielded low-voltage plastic cables. It ensures electrical insulation and mechanical protection of cable joints. The SVHC-free premium joint kit, tested according to EN 50393, can be used indoors and outdoors, underground or underwater. The transparent, one-piece casting shell can be folded up in no time at all and closes by automatically snapping into place. Pre-formed, perforated foam seals are also used. This eliminates the previously time-consuming use of saws and adhesive tape for a tight seal. A GMG system (closed mixing and pouring) is used when casting the cast resin 40 included in the scope of delivery. This means that contact with the casting resin during processing is practically impossible. The transparent mixing bag guarantees visual control of the mixing process. After use, the mixing bag with the remaining hardened casting resin can be disposed of as normal household waste. Disposal as hazardous waste is not necessary.
Sales unit: 10 pieces
Lieske Part No.: 555341

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 25 pieces
Lieske Part No.: 882443

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 15 pieces
Lieske Part No.: 543870

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 15 pieces
Lieske Part No.: 760098

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 15 pieces
Lieske Part No.: 342227

Heat Shrink Tubing GTI is a flexible RoHS heat shrink tubing range. The tubes have a flame retardant wall made of cross-linked polyolefin. They provide reliable performance for electrical splices, joints and connections up to 600V. GTI heat shrink tubing is available in many different colors and sizes with a shrink ratio of 2:1. This GTI heat shrink tubing kit comes in a convenient sorting box (size 270mm x 160mm x 60mm).
Heat shrink tubing GTI is color coded for quick and easy wire identification. This split-resistant, flame retardant tubing is used as a shrink fit as well as electrical insulation over cable splices or terminations. The tubing with a 2:1 expansion ratio is mechanically tough, easily markable and resists cold flow. The tubing is ideal for lightweight harness covering, fire resistant covering, cable marking, cable bundling and component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 4 pieces
Lieske Part No.: 329876

3MT Heat Shrink Tubing GTI is a RoHS flexible heat shrink tubing range. The tubes have a flame retardant wall made of cross-linked polyolefin. They provide reliable performance for electrical splices, joints and connections up to 600V. GTI heat shrink tubing is available in many different colors and sizes with a shrink ratio of 2:1. This GTI heat shrink tubing kit is supplied in a convenient sorting box (size 270mm x 160mm x 60mm).
3MT Heat Shrink Tubing GTI is color coded for quick and easy wire identification. This split-resistant, flame retardant tubing is used as a shrink fit as well as electrical insulation over cable splices or terminations. The tubing with a 2:1 expansion ratio is mechanically tough, easily markable and resists cold flow. The tubing is ideal for lightweight harness covering, fire resistant covering, cable marking, cable bundling and component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 4 pieces
Lieske Part No.: 335098

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 20 pieces
Lieske Part No.: 313372

GTI-3000 tubing is co-extruded and features an inner seal. The inner seal securely seals complex parts while the outer wall provides good mechanical protection. The GTI-A 3000 has a shrink ratio of 3:1. The GTI-A 3000 heat
shrink tubing is split resistant, features an inner seal and is used as a shrink fit or electrical insulation over cable splices or terminations. The tubing with an expansion ratio of 3:1 is mechanically robust, easily markable and resists cold flow. Temperature resistant from -55 to 135 °C.
Sales unit: 10 pieces
Lieske Part No.: 110003

GTI-3000 tubing is co-extruded and features an inner seal. The inner seal securely seals complex parts while the outer wall provides good mechanical protection. The GTI-A 3000 has a shrink ratio of 3:1. The GTI-A 3000 heat
shrink tubing is split resistant, features an inner seal and is used as a shrink fit or electrical insulation over cable splices or terminations. The tubing with an expansion ratio of 3:1 is mechanically robust, easily markable and resists cold flow. Temperature resistant from -55 to 135 °C.
Sales unit: 20 pieces
Lieske Part No.: 139126

8420 and 8430 cold shrink insulation tubing is EPDM tubing that is a unique cold shrink connection system. The products are supplied pre-stretched on a retractable support coil, allowing efficient and easy assembly. When the support coil is retracted after the tubing is positioned, the tubing shrinks to form a watertight seal. The active deformation of the specially formulated material ensures a permanent seal and insulation from the environment.
8420 and 8430 series cold shrink insulation tubing is especially useful for electrical insulation on all solid dielectric (rubber or plastic) insulated wires and cable splices up to 1,000 V. They are suitable for indoor and outdoor use. They often provide good physical protection and environmental shielding on communication lines and other non-electrical applications (including cable jacket repairs). The temperature range is -40 °C to 90 °C. In applications where the product is continuously exposed to UV radiation, it should be wrapped with Super 33+T vinyl insulation tape or Self-vulcanizing silicone rubber tape 70, for example.
Sales unit: 10 pieces
Lieske Part No.: 339132

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 959528

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 523781

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 284574

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard pack as standard.
Sales unit: 100 pieces
Lieske Part No.: 155905

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard packs as standard.
Lieske Part No.: 320995

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard packs as standard.
Sales unit: 10 pieces
Lieske Part No.: 490004

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard pack as standard.
Lieske Part No.: 754316

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard packs as standard.
Sales unit: 5 pieces
Lieske Part No.: 256486

Heat shrink cable branch sleeves are used to insulate and seal cable breaks in multi-core armored or jacketed cables. This robust sleeve offers good electrical and mechanical protection. The cross-linked polyolefin construction, approved to MIL-I-81765/1, is semi-rigid and flame retardant.
The heat shrink cable branch sleeve has an internal adhesive coating that ensures reliable cable break sealing against environmental influences in cables and conductor ends. RoHS 2011/65/EU compliant.
Sales unit: 3 pieces
Lieske Part No.: 646632

Heat shrink cable branch sleeves are used to insulate and seal cable breaks in multi-core armored or jacketed cables. This robust sleeve offers good electrical and mechanical protection. The cross-linked polyolefin construction, approved to MIL-I-81765/1, is semi-rigid and flame retardant.
The heat shrink cable branch sleeve has an internal adhesive coating that ensures reliable cable break sealing against environmental influences in cables and conductor ends. RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 574248

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard packs as standard.
Lieske Part No.: 951179

Waterproof and durable - the cable end fitting for the highest demands.
The 3MT voltage-resistant cable end fitting SKE S is suitable as an end termination for all live four-core plastic cables in the low-voltage range. It consists of four inner and one outer caps, with the outer cap marked with an abrasion-resistant voltage symbol. The heat-shrinkable cable end fitting is completely waterproof thanks to the thick hot-melt adhesive coating on the caps. It also has high mechanical strength and is resistant to UV rays, ozone, oxygen and acids. This ensures high electrical operational reliability at the cable end and is therefore ideal for both outdoor and underground installations.
Sales unit: 5 pieces
Lieske Part No.: 597294

The SKE heat shrink cable end cap ensures mechanical and environmental protection as well as sealing of cable ends. The end cap is made of semi-rigid, flame retardant polyolefin and is suitable for demanding applications. The adhesive coating ensures durable, flexible and waterproof protection.
The SKE is a semi-rigid cross-linked modified heat shrink polyolefin cable end cap with hot melt adhesive. The minimum shrink temperature is 120 °C, the operating temperature ranges from -30 °C to 135 °C. THE SKE is RoHS compliant, halogen-free and ensures good corrosion resistance. When heated, the adhesive melts and the cap shrinks, thereby ensuring a perfect watertight seal. The end caps enable quick and easy insulation and sealing of cable ends indoors and outdoors and are characterized by resistance to abrasion, weathering and chemical attack. The SKE is black and available in sizes from 8/4 to 126/63 mm, the wall thickness (after shrinkage) is 2.5 to 4.0 mm. Available as bulk or standard packs as standard.
Lieske Part No.: 603673

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 973530

The HDCW heat shrink tubing is designed for the quick repair of damaged cable sheaths. This winding sleeve is suitable for use for cable and splice insulation up to 1,000 V and can be used as cable sheath material up to 35 kV. It is made of cross-linked polyolefin and has an adhesive that ensures a seal against moisture.
HDCW heat shrink tubing offers excellent protection against mechanical stress. This winding sleeve with hot melt adhesive ensures a permanent and moisture-resistant seal. It is made of cross-linked polyolefin that can withstand adverse application conditions. The design of the winding sleeve enables installation in confined spaces with normal heating. Meets the requirements of ANSI C119.1 and is RoHS compliant.
Sales unit: 5 pieces
Lieske Part No.: 204391

Heat-shrink wall feedthrough for permanently gas- and watertight cable entries into the building.
The 3MT heat-shrink wall feedthrough WMD is used to seal telecommunications and power cables in wall feedthroughs. It enables gas- and watertight introduction of cables and pipes into the building. The cables or pipes can also be pulled in at a later date and installation as a reserve feedthrough is also possible. The wavy surface of the wall feedthrough is coated with a special sealing material. This allows you to achieve a permanently waterproof seal when closing the breakthrough opening with mortar or cement. The scope of delivery consists of a polyolefin shrink tube shrunk onto a support spiral, a cable cleaning cloth and the assembly instructions.
Sales unit: 5 pieces
Lieske Part No.: 914517

Safe and easy to install - the heat-shrink telecommunications set with temperature indicator.
The 3MT heat-shrink telecommunications connection and branch set FVAM is suitable for all filled and unfilled telecommunications and signal cables without compressed air monitoring. The set complies with the 'Technical Delivery Conditions of Deutsche Telekom AG'. The protective insert supplied serves as a water vapor barrier and to protect the cable splice from excessive heat and for mechanical protection. A coating with temperature indicator paint on the outside of the sleeve indicates the end of the shrinking process by changing color. A rust-proof locking rail prevents the sleeve from opening or warping during shrinking. The scope of delivery of the connection and branch set includes a heat-shrink sleeve with temperature indicator paint, locking rail, protective insert, shield connector and connection cable, cable cleaning cloth, emery cloth and assembly instructions. A branch system is not included in the scope of delivery.
Sales unit: 3 pieces
Lieske Part No.: 837647

Heat-shrink wall feedthrough for permanently gas- and watertight cable entries into the building.
The 3MT heat-shrink wall feedthrough WMD is used to seal telecommunications and power cables in wall feedthroughs. It enables gas- and watertight introduction of cables and pipes into the building. The cables or pipes can also be pulled in at a later date and installation as a reserve feedthrough is also possible. The wavy surface of the wall feedthrough is coated with a special sealing material. This allows you to achieve a permanently waterproof seal when closing the breakthrough opening with mortar or cement. The scope of delivery consists of a polyolefin shrink tube shrunk onto a support spiral, a cable cleaning cloth and the assembly instructions.
Sales unit: 5 pieces
Lieske Part No.: 843616

3M QTII Cold Shrink Outdoor Cable Terminator, 1 Conductor
The 5620K Series Cold Shrink Outdoor Cable Terminator Kit is designed for terminating medium voltage solid dielectric insulated cables in indoor applications. When the core of the cable termination is unwound, it shrinks over the cable, providing a perfect, leak-proof fit. The cable termination's tracking-resistant silicone rubber insulation ensures long service life. Approved for weatherproof applications.
Lieske Part No.: 829462

3M QTII Cold Shrink Outdoor Cable Termination, 1 Conductor
The 3MT Cold Shrink Cable Termination Kit, 5620K Series, is designed for terminating medium voltage solid dielectric insulated cables in indoor applications. When the core of the cable termination is unwound, it shrinks over the cable, ensuring a perfect, leak-proof fit. The cable termination's tracking-resistant silicone rubber insulation ensures long service life. Approved for weatherproof applications.
Sales unit: 4 pieces
Lieske Part No.: 495816

Flame-retardant casting resin that impresses with its very good chemical resistance. The casting resin is hydrophobic and can therefore harden in water.
3MT ScotchcastT 1402FR polyurethane resin in a bag is suitable as electrical insulation and mechanical protection of electrical connections for use up to 1 kV. It meets the requirements of CENELEC HD631.1 S2 and is compliant with EU Directive 2002/95/EC (RoHS) and EU Directive 1907/2007/EC (REACH) and guarantees the highest level of electrical insulation for professional use. Fast and clean application is possible thanks to the new, patented 3MT filler neck integrated into the resin bag. Bag opener is included in delivery.
Sales unit: 10 pieces
Lieske Part No.: 542632

The 3MT ScotchcastT Premium Resin Cable Joint Kits contain ScotchcastT Cable Resin 40, a high-quality, two-component polyurethane compound developed for general electrical insulation, moisture sealing and mechanical protection.
The 3MT ScotchcastT Cast Resin Joint Kit of the 92-NBA series is designed for one to five-core, unshielded low-voltage plastic cables. It ensures electrical insulation and mechanical protection of cable joints. The SVHC-free, premium joint kit, tested according to EN 50393, can be used indoors and outdoors, underground or underwater. The transparent, one-piece potting shell can be folded up in an instant and closes with an automatic snap-in. Pre-formed, perforated foam seals are also used. This eliminates the previously time-consuming use of a saw and adhesive tape for a tight seal. A GMG system (closed mixing and pouring) is used when casting the 3MT ScotchcastT casting resin 40 included in the delivery. This means that contact with the casting resin during processing is practically impossible. The transparent mixing bag guarantees visual control of the mixing process. After use, the mixing bag with the remaining hardened casting resin can be disposed of as normal household waste. Disposal as hazardous waste is not necessary.
Sales unit: 10 pieces
Lieske Part No.: 765652

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 10 pieces
Lieske Part No.: 759118

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 452899

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 418840

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 135290

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 904828

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 930750

Robust and versatile - the thin-walled heat shrink tubing without hot melt adhesive in the practical dispenser box.
The HSR heat shrink tubing is a thin-walled heat shrink tubing made of modified, radiation-crosslinked polyolefin. It is suitable for a wide range of applications, especially for electrical insulation and marking of connections. The heat shrink tubing is extremely resistant to aging and remains highly flexible over the long term. Its shrinkage rate is two to one. It is self-extinguishing and can be used in a temperature range from -55 °C to +135 °C. The dispenser box supplied enables efficient storage and handling, as you can easily shorten the tubing to the ideal length.
Sales unit: 5 pieces
Lieske Part No.: 942183

MDT-A heat shrink tubing is a medium-walled heat shrink tubing range with hot melt adhesive that ensures reliable performance for electrical splices, connections and terminations up to 1.0 kV as well as mechanical and environmental protection. MDT-A heat shrink tubing has a halogen-free, cross-linked polyolefin outer wall and a factory-applied adhesive layer on the inside.
MDT-A heat shrink tubing is a halogen-free, medium-walled heat shrink tubing made of radiation-cross-linked polyolefin with a hot melt adhesive coating. The hot melt adhesive penetrates all uneven surfaces and cavities and prevents moisture from penetrating. MDT-A heat shrink tubing is suitable for insulating plastic and ground cables up to 0.6/1 kV for both outdoor and underground installation. The age-resistant heat shrink tubing is UV-resistant and resistant to many chemical influences. It can be used in a temperature range from -55 °C to +130 °C. Thanks to its high shrink ratio of 4.5 to one, you can accommodate large diameter changes with just one tube. The MDT-A heat shrink tubing meets the technical requirements of IEC 60684 and is approved according to Lloyds Register of Shipping, certificate 95/30032(E5). It is halogen-free and RoHS compliant.
Sales unit: 10 pieces
Lieske Part No.: 505825

HSR-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing
made from cross-linked halogen-free polyolefin. HSR 3000 provides good insulation protection in various industrial
applications. It is also suitable for cable marking and identification applications. HSR 3000
tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
HSR-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant, halogen-free tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 861734

HSR-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing
made from cross-linked halogen-free polyolefin. HSR 3000 provides good insulation protection in various industrial
applications. It is also suitable for cable marking and identification applications. HSR 3000
tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
HSR-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant, halogen-free tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 977651

HSR-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing
made from cross-linked halogen-free polyolefin. HSR 3000 provides good insulation protection in various industrial
applications. It is also suitable for cable marking and identification applications. HSR 3000
tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
HSR-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant, halogen-free tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 844704

HSR-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing
made from cross-linked halogen-free polyolefin. HSR 3000 provides good insulation protection in various industrial
applications. It is also suitable for cable marking and identification applications. HSR 3000
tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
HSR-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant, halogen-free tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 5 pieces
Lieske Part No.: 342666

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 20 pieces
Lieske Part No.: 354941

GTI-3000 heat shrink tubing is a range of flexible, thin-wall RoHS heat shrink tubing made from cross-linked, halogen-free polyolefin. GTI 3000 offers good insulation protection in various industrial applications. They are also suitable for cable marking and identification applications. GTI 3000 tubing has a 3:1 shrink ratio and is available in the following colours: Clear, black, red, yellow, blue, white, green, grey, and green/yellow stripe.
GTI-3000 heat shrink tubing is colour coded for quick and easy wire identification. This split-resistant tubing is used as shrinkable, electrical insulation over cable splices or terminations. The tubing, with a 3:1 expansion ratio, is mechanically tough, easily markable and resists cold flow. It is ideal as a lightweight protective covering for wire harnesses, for wire marking and bundling, and for component packaging. It is temperature resistant from -55 to 135 °C and RoHS 2011/65/EU compliant.
Sales unit: 10 pieces
Lieske Part No.: 384408