Installation Material from Cellpack

Universally applicable for connecting plastic cables with concentric conductors and insulation made of PVC, PE and XLPE (e.g. N(A)YCY, N(A)YC(W)Y, GKN). Suitable for compression connectors.
Lieske Part No.: 135903

Universally applicable for connecting plastic cables with concentric conductors and insulation made of PVC, PE and XLPE (e.g. N(A)YCY, N(A)YC(W)Y, GKN). Suitable for compression connectors.
Lieske Part No.: 107384

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 1583795

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 898416

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 970377

Die Warmschrumpfschläuche vom Typ SB 3:1 sind dünnwandig, ohne thermoplastischem Kleber mit einer Schrumpfrate 3:1. Typische Anwendungsgebiete sind der Schutz von Kabel gegen chemische Einflüsse sowie ein guter mechanische Schutz. Verkaufseinheit: 1 ST.
Lieske Part No.: 494974

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 1311303

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 976263

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 897510

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 897530

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 897887

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 897888

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 897889

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 252412

The heat shrink tubing type SR1F3 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications include protecting cables against chemical influences and providing good mechanical protection.
Sales unit: 10 pieces
Lieske Part No.: 737032

Die Warmschrumpfschläuche vom Typ SR1F3 sind dünnwandig, ohne thermoplastischem Kleber mit einer Schrumpfrate 3:1. Typische Anwendungsgebiete sind der Schutz von Kabel gegen chemische Einflüsse sowie ein guter mechanische Schutz. Verkaufseinheit: 1 ST.
Sales unit: 10 pieces
Lieske Part No.: 494471

The heat shrink tubing type SR1F3 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications include protecting cables against chemical influences and providing good mechanical protection.
Sales unit: 10 pieces
Lieske Part No.: 897890

The heat shrink tubing type SR1F3 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications include protecting cables against chemical influences and providing good mechanical protection.
Sales unit: 10 pieces
Lieske Part No.: 299851

The heat shrink tubing type SR1F3 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications include protecting cables against chemical influences and providing good mechanical protection.
Sales unit: 10 pieces
Lieske Part No.: 971251

The heat shrink tubing type SR1F3 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications include protecting cables against chemical influences and providing good mechanical protection.
Sales unit: 10 pieces
Lieske Part No.: 897891

Die Warmschrumpfschläuche vom Typ SR1F3 sind dünnwandig, ohne thermoplastischem Kleber mit einer Schrumpfrate 3:1. Typische Anwendungsgebiete sind der Schutz von Kabel gegen chemische Einflüsse sowie ein guter mechanische Schutz. Verkaufseinheit: 1 ST.
Sales unit: 10 pieces
Lieske Part No.: 494472

The heat shrink tubing type SR1F3 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications include protecting cables against chemical influences and providing good mechanical protection.
Sales unit: 10 pieces
Lieske Part No.: 501797

The heat shrink tubing type SR1F3 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications include protecting cables against chemical influences and providing good mechanical protection.
Sales unit: 10 pieces
Lieske Part No.: 799442

The heat shrink tubing type SR1F3 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications include protecting cables against chemical influences and providing good mechanical protection.
Sales unit: 10 pieces
Lieske Part No.: 853122

The heat shrink tubing type SR1F3 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications include protecting cables against chemical influences and providing good mechanical protection.
Sales unit: 10 pieces
Lieske Part No.: 385986

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 108877

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 584095

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 610844

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Lieske Part No.: 395528

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Sales unit: 5 pieces
Lieske Part No.: 898424

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Sales unit: 5 pieces
Lieske Part No.: 134169

The heat shrink tubing type SB 3:1 is thin-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical areas of application are the protection of cables against chemical influences as well as good mechanical protection.
Sales unit: 5 pieces
Lieske Part No.: 577586

Universally applicable for connecting cables with EPR insulation (e.g. A07RN-F, H07RN-F). Suitable for press connectors.
Lieske Part No.: 1346063

Sealing 5-finger distribution cap for plastic, rubber and paper insulated cables.
Sales unit: 5 pieces
Lieske Part No.: 1323841

Sealing 5-finger distribution cap for plastic, rubber and paper insulated cables.
Sales unit: 5 pieces
Lieske Part No.: 196871

Sealing 5-finger distribution cap for plastic, rubber and paper insulated cables.
Sales unit: 5 pieces
Lieske Part No.: 994312

Die Warmschrumpfschläuche vom Typ SRBB sind mittelwandig, ohne thermoplastischem Kleber mit einer Schrumpfrate 3:1. Typische Anwendungsgebiete sind Mittelspannungs-Schaltanlagen bis 36 kV sowie Schutz gegen Korrosion. Verkaufseinheit: 1 ST.
Lieske Part No.: 500184

Die Warmschrumpfschläuche vom Typ SRBB sind mittelwandig, ohne thermoplastischem Kleber mit einer Schrumpfrate 3:1. Typische Anwendungsgebiete sind Mittelspannungs-Schaltanlagen bis 36 kV sowie Schutz gegen Korrosion. Verkaufseinheit: 1 ST.
Lieske Part No.: 500185

The heat shrink tubing type SRBB is medium-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications are medium-voltage switchgear up to 36 kV and protection against corrosion.
Lieske Part No.: 1564605

The heat shrink tubing type SRBB is medium-walled, without thermoplastic adhesive and has a shrink ratio of 3:1. Typical applications are medium-voltage switchgear up to 36 kV and protection against corrosion.
Lieske Part No.: 1323840

The SRUM type heat shrink tubing is medium-walled, with thermoplastic adhesive with a shrink ratio of 4:1. Typical areas of application are pressure and moisture protection of cables as well as use in shrink sleeves and shrink end closures.
Sales unit: 10 pieces
Lieske Part No.: 829067

The SRUM type heat shrink tubing is medium-walled, with thermoplastic adhesive with a shrink ratio of 4:1. Typical areas of application are pressure and moisture protection of cables as well as use in shrink sleeves and shrink end closures.
Sales unit: 10 pieces
Lieske Part No.: 933146

The SRUM type heat shrink tubing is medium-walled, with thermoplastic adhesive with a shrink ratio of 4:1. Typical areas of application are pressure and moisture protection of cables as well as use in shrink sleeves and shrink end closures.
Sales unit: 10 pieces
Lieske Part No.: 909486

The SRUM type heat shrink tubing is medium-walled, with thermoplastic adhesive with a shrink ratio of 4:1. Typical areas of application are pressure and moisture protection of cables as well as use in shrink sleeves and shrink end closures.
Lieske Part No.: 471678

The SRUM type heat shrink tubing is medium-walled, with thermoplastic adhesive with a shrink ratio of 4:1. Typical areas of application are pressure and moisture protection of cables as well as use in shrink sleeves and shrink end closures.
Lieske Part No.: 594731

Mouldable, thermoplastic putty sealant based on butyl rubber. It can be easily moulded into precise shapes and allows for quick and high-quality sealing options.
Lieske Part No.: 968076

The pluggable Cellplux angle cable connectors CWS are suitable for the connection of all single-core cables with XLPE or (H)EPR) insulation, with PVC or PE outer sheath, with different conductive layers (stripable or removable) as well as shield designs (wire or tape shield) to switchgear, transformers and junction boxes for maximum mains voltage up to 36 kV for bushings with outer cone type B according to EN 50180 and EN 50181.
Lieske Part No.: 181984

The pluggable Cellplux angle cable connectors CWS are suitable for the connection of all single-core cables with XLPE or (H)EPR) insulation, with PVC or PE outer sheath, with different conductive layers (stripable or removable) as well as shield designs (wire or tape shield) to switchgear, transformers and junction boxes for maximum mains voltage up to 36 kV for bushings with outer cone type B according to EN 50180 and EN 50181.
Lieske Part No.: 140709

The pluggable Cellplux angle cable connectors CWS are suitable for the connection of all single-core cables with XLPE or (H)EPR) insulation, with PVC or PE outer sheath, with different conductive layers (stripable or removable) as well as shield designs (wire or tape shield) to switchgear, transformers and junction boxes for maximum mains voltage up to 36 kV for bushings with outer cone type B according to EN 50180 and EN 50181.
Lieske Part No.: 141014

For quickly connecting and insulating drilled or otherwise damaged cables without inserting new cable parts. The cable repair kit restores the electrical and mechanical properties of the installation cable.
Sales unit: 20 pieces
Lieske Part No.: 288791