Triton RTA-47-A66-CAX-A1
48,3 cm ( 19 inch )-Schrank, Standschrank für Belastung 1200 kg, 47HE/600x600, Glastür, grau content_copy

Welded frame with removable side and rear panels, IP20, load capacity 1200 / 1500 kg
Description, intended use48,3 cm ( 19 inch ) upright distribution board with IP20 degree of protection
The distribution board consists of 4 adjustable vertical latching rails for mounting components (6 in distribution boards deeper than 800 mm)
Distribution board construction: Welded steel frame with removable walls
Single- or double-leaf doors in the following versions Double-leaf doors in solid sheet metal, perforated (80% and 86% air passage) or glass door versions with 4 mm thick safety glass. They can be mounted at the front or rear of the distribution board
Preparation for mounting vertical cable routing panels and socket strips, including fixings, on the frame
Preparation for easy baying of enclosures
The A5 and A7 versions also have concealed cable entries in the uprights for easy cable routing between the distribution boards
The maximum permissible load capacity of the individual doors is 20kg
. 20kg
These enclosures are designed for the installation of data and telecommunications systems and their distribution systems
The distribution frame and all removable parts (side and rear panels, doors, etc.) are connected with earthing cables. ) are connected with earthing cables that must be properly secured and plugged in throughout the entire service life of the enclosure
An M8 screw is located in the base of the enclosure as the main earthing point
Cable entries with break-out covers are located at the top and bottom
Operating conditionsConditions of use: Offices
The distribution board is not intended for outdoor use or under conditions that may have a negative impact on its function and that of the installed components (e.g. environment with explosion hazard or environment with a risk of explosion).
It must be protected against:mechanical damage
improper handling
use other than that intended for the distributor
Improper handling means in particular:overloading (exceeding the recommended maximum load)
installation of equipment that may negatively affect the operation and functioning of the distributor or the installed components
. of the installed components
Interventions in the distributor construction and its design
Installation of the distributorIn order to ensure the recommended maximum load, the load must be distributed evenly
The distributor must be installed on a level surface; any minor unevenness can be levelled out using the levelling feet, which are part of the accessory pack
In the event that cables are inserted through one of the openings, these can be sealed against dust with the brush strip and fitted with the protective frame (both part of the accessory pack)
Environmental protectionAll parts are made from recyclable materials. They must be disposed of in accordance with the applicable regulations after the distributor has been decommissioned
Properties, material and dimensionsToughened safety glass with a thickness of 4 mm, deep-drawn steel sheet
Reinforced frame: 1.3 mm sheet steel
Four-point base rail support: 2.5 mm sheet steel
Triton swivelling lever handles: By replacing the plastic module (not included in the accessory pack), you can choose between a classic and semi-cylindrical locking mechanism. Patent: PUV 2013-27443.
Wider cabinet corners: The wider cabinet corners are designed for the additional installation of 48,3 cm ( 19 inch ) socket strips, so that no space is required in the cabinet for them. Thanks to the well thought-out mounting, extendable servers are not obstructed even in 600 mm wide distribution boards. In addition, the A5 version (at the end of the enclosure code) has break-out openings in the frame through which cables can be pulled between adjacent enclosures.
Perforated supports: The openings over the entire height of the uprights correspond to the U spacing of the verticals
Laser designation of the verticals: sheet steel 2 mm.
M8 main earthing point
Plug-in hinges: The standard door hinges can be replaced with plug-in hinges.
Earthing: All removable parts are interconnected in accordance with the requirements of the relevant standards
Breakaway panels
Edging tape: 1 m included in the accessory pack.
800 mm wide distributors: 15 - 47 U
Flex frame: The system enables the installation of adjustable rails at a distance of 48,3 cm ( 19 inch ), 53,3 cm ( 21 inch ) and 58,4 cm ( 23 inch ) with a width of 800 mm.
Increased load capacity from 1200 kg to 1500 kg:Reinforcing element for the vertical raster rails: The closed 1.5 mm (consisting of 4 parts) thick profile increases the load capacity of the tundish to up to 1500 kg. Recommended stabilisation set RAX-VR-Txx-Yx for 800 mm wide distributors. Its assembly stabilises the distributor and at the same time enables vertical cable routing.
Included:Side panel key 2x
Door key 2x
Cage nut M6 16x
Brush strip 1x
Edging tape 1m
Levelling feet 4x
M10 nut 4x

Technical data
Colour	Grey (RAL7035)
Rear panel/door	Solid sheet metal rear panel, with two safety locks
Width packaging	0.600m
Side panel left	Solid sheet metal, with two safety locks
Weight	88.690kg
Height unit	47U
Front door	Glass door left hinge
Side panel right	Solid sheet metal, with two safety locks
Locking of rear door	Safety lock for rear panel
Height (outside)	2194mm
Length packaging	0.600m
Depth	600mm
Product note	The cabinet height is specified without the levelling feet supplied in the accessories pack. If these feet are mounted, the installation dimension of the cabinet is increased by 24 to 35 mm.
Width	600mm
Recommended maximum load	1200/1500kg
Packaging volume	0.7898m³
Maximum spacing of vertical rails	484mm
Door width	487mm
Locking of front door	Single-point locking, safety lock
Door height	2092mm
Height packaging	2.194m
Protection class	IP30
Detachable rear panel
Detachable side panels
Demountable

---