Schneider Electric LXM28AU10M3X Motion Servo drive Lexium 28 200/230 V 1+3 ph 1 kW content_copy

LXM28 servo amplifier from the Lexium 28 servo drive range. These servo drives offer predefined combinations of amplifiers and motors to meet motion control applications, optimize performance and offer very simple integration and commissioning in your system. They include numerous functions such as auto-tuning, position, speed and torque control as well as position sequence mode. Their compact dimensions allow easy installation even in tight control cabinets. The supply voltage of this servo controller is 200-240 VAC from single or three-phase networks. A nominal power of 100 W is provided at the output. The interfaces available are: PTI/PTO, analog 2 inputs (+-10 V) and 2 outputs (+- 8 V), digitally configurable 8 inputs and 6 outputs. The fieldbus connection and motion control from a PLCopen library are carried out via CANopen or CANmotion. The STO safety function is implemented up to PL d/SIL2. An internal braking resistor is available to absorb the braking energy. An external resistor can also be connected for frequent braking operations. An output enables the holding brake to be controlled. The associated BCH2 servo motors from the Lexium 28 series must be used for operation. Thanks to the Green Premium eco-label, you can obtain detailed information on material content, environmental impact and circular economy that supports your sustainability goals.

Complementary
Network number of phases	Single phase; Three phase
[Us] rated supply voltage	200...240 V (- 10...15 %) for three phase; 200...240 V (- 20...15 %) for single phase
Supply voltage limits	200…255 V three phase; 170…255 V single phase
Supply frequency	50/60 Hz - 5...5 %
Network frequency	47.5...63 Hz
EMC filter	Without EMC filter
Continuous output current	7 A at 16 kHz
Output current 3s peak	21 A at 220 V
Continuous power	1000 W at 220 V
Nominal power	1 kW at 220 V 16 kHz
Switching frequency	16 kHz
Overvoltage category	III
Maximum leakage current	4.5 mA
Electrical isolation	Between power and control
Type of cable	Shielded motor cable (temperature: 0…55 °C) copper
Electrical connection	Spring terminal, clamping capacity: 1.3...1.5 mm², 16 AWG (L1-L2); Spring terminal, clamping capacity: 1.3...1.5 mm², 16 AWG (R, S, T); Spring terminal, clamping capacity: 1.3...1.5 mm², 16 AWG (U, V, W, PE); Spring terminal, clamping capacity: 1.3...1.5 mm², 16 AWG (PA/+, PBe)
Discrete input number	8 programmable (CN1); 1 pulse train input (PTI) (CN1); 2 fast capture (CN1); 1 safety function STO (CN9)
Discrete input voltage	24 V DC for logic
Discrete input logic	Positive or negative (CN1)
Discrete output number	5 logic output (CN1) at 12...24 V DC; 1 pulse train output (PTO) (CN1)
Discrete output voltage	12...24 V DC
Discrete output logic	Positive or negative (CN1)
Analogue input number	2
Absolute accuracy error	0.1 %
Analogue input type	V_REF voltage analog input: - 10...10 V, impedance: 10 kOhm, resolution: 14 bits; T_REF voltage analog input
Control signal type	Servo motor encoder feedback CN2
Protection type	Against reverse polarity: inputs signal; Against short-circuits: outputs signal; Overcurrent: motor; Overvoltage: motor; Undervoltage: motor; Overheating: motor; Overload: motor; Overspeed: motor
Safety function	STO (safe torque off), integrated
Safety level	SIL 2 conforming to IEC 61800-5-2: 2007; SIL 2 conforming to IEC 61508-1: 2010; PL d/category 3 conforming to ISO 13849-1: 2008; SIL 2 conforming to ISO 13849-1: 2009/AC; SIL 2 conforming to IEC 60204-1: 2006; SIL 2 conforming to IEC 60204-1: 2009/A1; SIL 2 conforming to IEC 60204-1: 2010/AC; SIL 2 conforming to IEC 62061: 2012
Communication interface	CANopen, integrated; CANmotion, integrated
Connector type	RJ45 (CN4) for CANopen, CANmotion
Method of access	Slave
Transmission rate	250 kbit/s for bus length of 100…250 m for CANopen, CANmotion; 500 kbit/s for bus length of 4…100 m for CANopen, CANmotion; 1 Mbit/s for bus length of 4 m for CANopen, CANmotion
Number of addresses	1…127 for CANopen, CANmotion
Physical interface	RS485 for Modbus Serial line slave
Status LED	1 LED (red) charge; 1 LED (green) RUN; 1 LED (red) error
Signalling function	Servo status and fault codes five 7-segment display units
Marking	CE; CULus
Type of cooling	Integrated fan
Operating position	Vertical
Product compatibility	Servo motor BCH2 (130 mm, 1 motor stacks) at 1000 W; Servo motor BCH2 (100 mm, 1 motor stacks) at 1000 W; Servo motor BCH2 (130 mm, 2 motor stacks) at 900 W; Servo motor BCH2 (130 mm, 4 motor stacks) at 850 W
Width	55 mm
Height	150 mm
Depth	170 mm
Net weight	1.2 kg
Supply voltage description	Three phase 220 V AC 50...60 Hz; Single phase 220 V AC 50...60 Hz
Drive voltage drop coefficient	1
Field weakening	False
Continuous output current 2	7 A
Switching frequency 2	16 kHz
Continuous output current 3	7 A
Switching frequency 3	16 kHz
Communication iinterface	CANmotion; Pulse train output; CANopen DS402; Pulse train input
Emc filter compatibility	Type 021; Type 022
Contractual warranty
Warranty (in months)	18
Environment
Electromagnetic compatibility	Conducted emission - test level: level 3 category C3 conforming to IEC 61800-3
Standards	IEC 61800-5-1
Product certifications	CE; cULus
IP degree of protection	IP20
Vibration resistance	3M4 amplitude = 3 mm (f = 9…200 Hz) conforming to IEC 60721-3-3
Shock resistance	10 gn, type I conforming to IEC 60721-3-3
Relative humidity	5…95 % without condensation
Ambient air temperature for operation	0…55 °C
Ambient air temperature for storage	-25…65 °C
Operating altitude	1000...2000 m 1 % per 100 m
Logistical informations
Country of origin	CN
Main
Range of product	Lexium 28
Device short name	LXM28A
Product or component type	Motion servo drive
Format of the drive	Compact housing
Line current	8.5 A 176.3 % at 220 V, single phase; 8.5 A 155.5 % at 220 V, three phase
Packing Units
Unit Type of Package 1	PCE
Number of Units in Package 1	1
Package 1 Height	7.500 cm
Package 1 Width	23.000 cm
Package 1 Length	23.500 cm
Package 1 Weight	1.499 kg
Unit Type of Package 2	S03
Number of Units in Package 2	5
Package 2 Height	30.000 cm
Package 2 Width	30.000 cm
Package 2 Length	40.000 cm
Package 2 Weight	7.990 kg

---