Schneider Electric ATS490C14Y ALTIVAR soft starter ATS490 140 A 208 to 690 V content_copy

Der AltivarSanftanlasser ATS490, ist dazu bestimmt, Asynchronmotoren, von 208 bis 690V, sanft zu starten und zu stoppen. Mit einem Wirkungsgrad von 99,5 %, speziellen Anwendungsfunktionen und vollständiger Überwachung mit Datenberichterstattung ermöglicht der ATS490 eine fortschrittliche Motorsteuerung. Zertifizierte Cybersicherheit, Safe Torque Off und Zustandsüberwachungsfunktionen erhöhen die Betriebszeit, senken die Betriebskosten und vereinfachen die Projektplanung. Der ATS490 bietet eine umfassende Systemüberwachung, einschließlich des Motors, der Anwendung, der Leistung und der Energie, mit einer Genauigkeit von über 95%. Der ATS490 verfügt über einen nativen Ethernet-Anschluss für Modbus TCP oder EtherNet/IP und einen seriellen Modbus-Anschluss. Der Altivar Sanftanlasser ATS490 erfüllt die Anforderungen von Anwendungen wie Pumpen, Ventilatoren, Kompressoren, Förderbändern, Mischern, Schneidemaschinen, Schleifmaschinen und Brechern. ATS490 entspricht IEC/EN 60947-4-2 und den Zertifizierungen CE, cULus, UKCA, RCM, CCC, EAC und DNV. Es sind viele Zubehörteile verfügbar, wie ein IP65-Montagesatz zur Befestigung des Grafik-Displays an der Schaltschranktür und Kommunikationsmodule zur Erweiterung der Konnektivität auf andere Protokolle. Die Verpackung besteht aus recyceltem Karton und enthält weniger Einwegplastik. Die ATS490-Sanftanlasser müssen vertikal in einem Gehäuse montiert werden. Die eingebauten und innovativen Funktionen des ATS490 verbessern die Wettbewerbsfähigkeit, die betriebliche Widerstandsfähigkeit und die Nachhaltigkeit der Ausrüstung. Der ATS490 Sanftanlasser reduziert die Total Cost of Ownership und betreibt selbst anspruchsvollste Applikationen.

Complementary
Device connection	In the motor supply line; Inside delta
Overload current profile	400 % Ie for 13 s
On-load factor	50 %
Operating cycles/hour	10 cyc/h
[Us] control circuit voltage	110...230 V AC 50...60 Hz - 15...10 %
Apparent power	80 VA
Integrated motor overload protection	True
motor thermal protection class	Class 10E
Protection type	Phase failure: mains; Thermal protection: starter; Thermal protection: motor; Current overload: motor; Motor underload: motor; Excessive acceleration time: motor; Motor phase loss detection: motor; Protection against line phase inversion: mains; External thermal protection: motor; Protection delta inside wiring: starter; Short-circuit between motor phase and earth: motor
current limiting %In (5 x Ie maximum)	150…700 %
Rated current pwr loss specification	140 A
Power loss static current independent	19 W
Power loss per device current dependent	26 W
Power loss during starting	1651 W during starting at 40 °C at 400% Ie
Standards	EN/IEC 60947-4-2; UL 60947-4-2; IEC 60664-1
Product certifications	CE; cULus; UKCA; RCM; CCC; DNV; ATEX; EAC; KC
Marking	CE; CULus; UKCA; RCM; CCC; ATEX; EAC; KC
[Uc] control circuit voltage	24 V DC
Discrete input number	5
Discrete input type	(DI1) digital input, 4.4 kOhm; (DI2) digital input, 4.4 kOhm; (DI3) digital input, 4.4 kOhm; (DI4) digital input, 4.4 kOhm; (STO) digital input, > 1 kOhm
Input compatibility	DI1: discrete input level 1 PLC conforming to EN/IEC 61131-2; DI2: discrete input level 1 PLC conforming to EN/IEC 61131-2; DI3: discrete input level 1 PLC conforming to EN/IEC 61131-2; DI4: discrete input level 1 PLC conforming to EN/IEC 61131-2; STO: discrete input level 1 PLC conforming to EN/IEC 61131-2
Discrete input logic	Digital input DI1 at State 0: 0...< 5 V and 11 V, >= 5 mA; Digital input DI2 at State 0: 0...< 5 V and 11 V, >= 5 mA; Digital input DI3 at State 0: 0...< 5 V and 11 V, >= 5 mA; Digital input DI4 at State 0: 0...< 5 V and 11 V, >= 5 mA; Digital input STO at State 0: 0...< 5 V and 11 V, >= 5 mA
Relay output number	3
Relay output type	Relay outputs R1A, R1C NO; Relay outputs R2A, R2C NO; Relay outputs R3A, R3C NO
Minimum switching current	100 mA at 12 V DC for relay outputs
Maximum switching current	Relay outputs 2 A / 250 V AC for AC-15 100000 cycles following IEC 60947-5-1; Relay outputs 2 A / 30 V DC for DC-13 150000 cycles following IEC 60947-5-1
Discrete output number	2
Discrete output type	Programmable digital output DQ1
Output compatibility	Open collector level 1 PLC conforming to IEC 65A-68
Analogue input number	1
Analogue input type	AI1/PTC1 : PTC/PT 100/PT 1000/KTY84 temperature probe; PTC2 : PTC/PT 100/PT 1000/KTY84 temperature probe; PTC3 : PTC/PT 100/PT 1000/KTY84 temperature probe
Analogue output number	1
Analogue output type	Current output AQ1 : 0...20 mA/4...20 mA , impedance< 500 Ohm; Voltage output AQ1 : 0...10 V , impedance> 470 Ohm
Connector type	1 RJ45 for connecting Modbus serial; 1 RJ45 for connecting Modbus TCP/EtherNet/IP
Physical interface	2-wire RS 485; 100-BASE-TX category 5 or industrial Ethernet
Transmission frame	RTU; TCP/UDP
Transmission rate	4.8…38.4 kbps; 100 BASE TX
Data format	8 bits, configurable odd, even or no parity 1or 2 stop
Number of addresses	0…247 for Modbus serial
Method of access	Slave Modbus serial
Type of polarization	No impedance for Modbus serial
Display screen available	True
Operating position	Vertical +/- 10 degree
Height	356 mm
Width	160 mm
Depth	235 mm
Net weight	10 kg
internal bypass	True
Function available	Pre-heating; Smoke extraction; Second motor set; Deceleration with torque control; Braking; Boost; Line contactor control; Reverse contactor control; Anti-jam; Jog; Borehole pump starting; Condition monitoring; Power monitoring; Cybersecure firmware update
material declaration	True
Contractual warranty
Warranty (in months)	18
Environment
Pollution degree	Level 3
[Uimp] rated impulse withstand voltage	6 kV
[Ui] rated insulation voltage	690 V
Environmental class (during operation)	Class 3C3 according to IEC 60721-3-3; Class 3S3 according to IEC 60721-3-3
Ambient air temperature for operation	-25…40 °C (without derating); 40…60 °C (with current derating of 1 % per °C above 40 °C)
Ambient air temperature for storage	-40…70 °C
Ambient air transport temperature	-40…70 °C
Operating altitude	2000...4800 m with current derating 1 % per 100 m above 2000 m
Relative humidity	5…95 % without condensation or dripping water conforming to EN/IEC 60068-2-3
Maximum deflection under vibratory load (during operation)	1.5 mm at 2...13 Hz
Maximum deflection under vibratory load (during storage)	1.75 mm at 2...9 Hz
Maximum deflection under vibratory load (during transport)	1.75 mm at 2...9 Hz
Maximum acceleration under vibrational stress (during operation)	1 gn at 13…200 Hz
Maximum acceleration under vibratory load (during storage)	1 gn at 9…200 Hz; 1.5 gn at 200…500 Hz
Maximum acceleration under vibratory load (during transport)	1 gn at 9…200 Hz; 1.5 gn at 200…500 Hz
Maximum acceleration under shock impact (during operation)	15 gn at 11 ms
Maximum acceleration under shock load (during storage)	10 gn at 11 ms
Maximum acceleration under shock load (during transport)	10 gn at 11 ms
Logistical informations
Country of origin	ID
Main
Range of product	Altivar Soft Starter ATS490
Product or component type	Soft starter
Product destination	Asynchronous motors
Product specific application	Process and infrastructures
Device short name	ATS490
Network number of phases	3 phases
Utilisation category	AC-3A; AC-53a
Ue power supply voltage	208...690 V AC (- 15...10 %)
power supply frequency	50...60 Hz - 20...20 %
[Ie] rated operational current	Normal duty: 140 A in line (at
Service factor at Ie	100
rated current in heavy duty	110 A at 40 °C for heavy duty
Torque control	True
IP degree of protection	IP00
Motor power hp	40 hp at 208 V normal duty; 50 hp at 230 V normal duty; 100 hp at 460 V normal duty; 125 hp at 575 V normal duty; 30 hp at 208 V heavy duty; 40 hp at 230 V heavy duty; 75 hp at 460 V heavy duty; 100 hp at 575 V heavy duty
With safety function Safe torque off (STO)	True
Safe Torque Off (STO)	STO (safe torque off): SIL 1 conforming to IEC 61508; STO (safe torque off): PL c/category 2 conforming to ISO 13849
Cybersecurity functions	True
Cybersecurity level and standard	Security level (SL) 1 conforming to IEC 62443-4-2
Communication port protocol	Modbus serial; Modbus TCP/EtherNet/IP
Option card	Communication module for CANopen daisy chain; Communication module for CANopen Sub-D; Communication module for CANopen open style; Communication module for Profibus DP V1; Communication module for PROFINET
Packing Units
Unit Type of Package 1	PCE
Number of Units in Package 1	1
Package 1 Height	23.500 cm
Package 1 Width	27.500 cm
Package 1 Length	45.000 cm
Package 1 Weight	11.770 kg
Unit Type of Package 2	S06
Number of Units in Package 2	6
Package 2 Height	75.000 cm
Package 2 Width	60.000 cm
Package 2 Length	80.000 cm
Package 2 Weight	79.600 kg

---