Screw in Fixing hardware

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 10 Screw length: 50 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081/4042, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 281317

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) Thread: M 10 Screw length: 70 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 48 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 50 pieces
Lieske Part No.: 729351

Hexagon screw according to DIN EN ISO 4017, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 12 Screw length: 50 mm Screw strength class: 10.9 Nut strength class: 10 Screw tightening torque: 123 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 20 pieces
Lieske Part No.: 169269

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 12 Screw length: 50 mm Screw strength class: 10.9 Nut strength class: 10 Screw tightening torque: 123 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 20 pieces
Lieske Part No.: 134554

Hexagon screw according to DIN EN ISO 4017, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 12 Screw length: 70 mm Screw strength class: 10.9 Nut strength class: 10 Screw tightening torque: 123 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 20 pieces
Lieske Part No.: 169273

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. For use in functional maintenance, please observe additional regulations! Dimensions (approx. dimensions) Thread: M 12 Screw length: 70 mm Screw strength class: 10.9 Nut strength class: 10 Screw tightening torque: 123 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 20 pieces
Lieske Part No.: 784993

Hexagon screw according to DIN EN ISO 4017, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 16 Screw length: 40 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 206 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 20 pieces
Lieske Part No.: 774576

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class is to be used to determine the torque. Dimensions (approx. dimensions) Thread: M 8 Screw length: 16 mm Screw strength class: 70 Nut strength class: 70 Screw tightening torque: 16 Nm Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 50 pieces
Lieske Part No.: 230404

Hexagon screw according to DIN EN ISO 4017, including hexagon nut according to DIN EN ISO 4032 and washer according to DIN EN ISO 7089. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class is to be used to determine the torque. Dimensions (approx. dimensions) Thread: M 8 Screw length: 16 mm Screw strength class: 70 Nut strength class: 70 Screw tightening torque: 16 Nm Material: stainless steel, material no. 1.4571
Sales unit: 50 pieces
Lieske Part No.: 774345

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class is to be used to determine the torque. Dimensions (approx. dimensions) Thread: M 8 Screw length: 16 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 24.6 Nm Material: Steel, hot-dip galvanized according to DIN EN ISO 10684
Sales unit: 10 pieces
Lieske Part No.: 234475

Hexagon screw according to DIN EN ISO 4017, including toothed flange nut according to DIN EN 1661. The strength class of the screw is stamped on the screw head. Especially for connections that have to transfer vertical loads through friction, it is essential to pay attention to the screw tightening torque and to check it with the torque wrench! In product combinations (hexagon screw with nut), the lower strength class must be used to determine the torque. Dimensions (approx. dimensions) Thread: M 8 Screw length: 16 mm Screw strength class: 8.8 Nut strength class: 8 Screw tightening torque: 24.6 Nm Material: Steel, galvanized according to DIN EN ISO 2081, 4042, blue passivated
Sales unit: 10 pieces
Lieske Part No.: 202613

Hexagon nut according to DIN EN ISO 4032, galvanized according to DIN EN ISO 4042, blue passivated. Thread: M10 Strength class: 8 Wrench size: SW 17 / SW 16
Sales unit: 100 pieces
Lieske Part No.: 409222

E-clips, turnbuckle, with hook and eyelet, for tightening the rope suspension. Dimensions (approx. dimensions) Hook and eyelet thread: M 6 Eyelet diameter: 10 mm Clamping range A: 155 - 245 mm Material: Stainless steel, material no. 1.4401, 1.4404
Sales unit: 10 pieces
Lieske Part No.: 537594

Beam clamp, pre-assembled, for mounting on beam flanges in accordance with DIN 1025 with a minimum dimension of 8 - 20 mm and a max. 14% inclination or parallel flanges with a flange thickness of 8 - 20 mm, for vertical suspensions using a threaded rod, pre-assembly of the beam clamp with the threaded rod before assembly is possible. The beam clamp may only be loaded perpendicular to the beam! for threaded rod: = M 8 Dimensions (approx. dimensions) Height H: 61 mm Width B: 17.5 mm Length L: 112 mm Beam flange thickness t: 8 - 20 mm Vertical nominal load F: 2.0 kN Material: Steel, strip galvanized in accordance with DIN EN 10346 Niedax model no.: TKM 1
Sales unit: 25 pieces
Lieske Part No.: 1327253

Beam clamp, pre-assembled, for mounting on beam flanges in accordance with DIN 1025 with a minimum dimension of 8 - 20 mm and a max. 14% inclination or parallel flanges with a flange thickness of 8 - 20 mm, for vertical suspensions using a threaded rod, pre-assembly of the beam clamp with the threaded rod before assembly is possible. The beam clamp may only be loaded perpendicular to the beam! for threaded rod: = M 10 Dimensions (approx. dimensions) Height H: 61 mm Width B: 19.5 mm Length L: 112 mm Beam flange thickness t: 8 - 20 mm Vertical nominal load F: 3.6 kN Material: Steel, strip galvanized in accordance with DIN EN 10346 Niedax model no.: TKM 2
Sales unit: 25 pieces
Lieske Part No.: 1327251

Beam clamp, pre-assembled, for mounting on beam flanges in accordance with DIN 1025 with a minimum dimension of 8 - 20 mm and a max. 14% inclination or parallel flanges with a flange thickness of 8 - 20 mm, for vertical suspensions using a threaded rod, pre-assembly of the beam clamp with the threaded rod before assembly is possible. The beam clamp may only be loaded perpendicular to the beam! for threaded rod: = M 12 Dimensions (approx. dimensions) Height H: 61 mm Width B: 21.5 mm Length L: 112 mm Beam flange thickness t: 8 - 20 mm Vertical nominal load F: 5 kN Material: Steel, strip galvanized in accordance with DIN EN 10346 Niedax model no.: TKM 3
Sales unit: 25 pieces
Lieske Part No.: 1327252

Body washer according to DIN EN ISO 7093-1, for covering larger mounting holes, for screws with M 12 thread. Dimensions (approx. dimensions) Inner Ø: 13 mm Outer Ø B: 37 mm Thickness t: 3 mm Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 100 pieces
Lieske Part No.: 564593

Body washer according to DIN EN ISO 7093-1, for covering larger mounting holes, for screws with M 12 thread. Dimensions (approx. dimensions) Inner Ø: 13 mm Outer Ø B: 37 mm Thickness t: 3 mm Material: Steel, galvanized according to DIN EN ISO 4042/2081, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 564598

Body washer according to DIN EN ISO 7093-1, for covering larger mounting holes, for screws with M 6 thread. Dimensions (approx. dimensions) Inner Ø: 6.4 mm Outer Ø B: 18 mm Thickness t: 1.6 mm Material: Stainless steel, material no. 1.4301, 1.4303
Sales unit: 100 pieces
Lieske Part No.: 375131

Body washer according to DIN EN ISO 7093-1, for covering larger mounting holes, for screws with M 8 thread. Dimensions (approx. dimensions) Inner Ø: 8.4 mm Outer Ø B: 24 mm Thickness t: 2 mm Material: Steel, hot-dip galvanized according to DIN EN ISO 1461
Sales unit: 100 pieces
Lieske Part No.: 163112

NIEDAX - Make: U.S. M10
washer, steel according to DIN EN ISO 7089, DIN 50961 zinc plated, blue passivated, for screws with thread M 10 NIEDAX Model No.: U.S. M10. Type: USM10




Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 137426

Washer according to DIN EN ISO 7089, for screws with thread M 12. Dimensions (approx. dimensions) Inner Ø: 13 mm Outer Ø: 24 mm Thickness t: 2.5 mm Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 369778

Washer according to DIN EN ISO 7089, for screws with thread M 5. Dimensions (approx. dimensions) Inner Ø: 5.3 mm Outer Ø: 10 mm Thickness t: 1 mm Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 504240

Washer according to DIN EN ISO 7089, for screws with thread M 6. Dimensions (approx. dimensions) Inner Ø: 6.4 mm Outer Ø: 12.5 mm Thickness t: 1.6 mm Material: Steel, galvanized according to DIN EN ISO 2081, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 234020

NIEDAX - Make: U.S. M8
washer, steel according to DIN EN ISO 7089, DIN 50961 zinc plated, blue passivated, for screws with thread M 8 NIEDAX Model No.: U.S. M8. Type: USM8




Quantity: 1 unit.
Sales unit: 100 pieces
Lieske Part No.: 245423

Weitspannträgerklemme, zur Klemmbefestigung von Weitspannkabelrinnen und -leitern an waagerecht kreuzenden Tägern, eine versetzt angeordnete Anordnung der Klemme verhindert eine Bewegung in Längsrichtung während der Montage, zwei Kerbstellen am Klemmschenkel ermöglichen eine Anpassung des Schenkels an kürzere Trägerflansche, einschließlich galv. verz. Befestigungszubehör für Kabelrinnen 2 FLM 6X12 V sowie feuerverzinktes Befestigungszubehör für Kabelleitern und Weitspannkabelrinnen /-leitern 2 FLM 8X13 F. für Kabelrinnen : RL ... / RLU ... RLV ... RLCI ... RS .... / RSU ... RLC ... / RLUC ... RLCPV ... für Kabelleitern : KL ... für Weitspannkabelrinnen : WRL ... WRLM ... WRU ... für Weitspannkabelleitern : WSL ... WSLM ... WSLS ... Abmessungen (ca. Maße) H x B x t : 82 x 150 x 2 mm Flanschstärke des Trägers t : 8 - 22 mm Werkstoff : Stahl, bandverzinkt nach DIN EN 10346 Verkaufseinheit: 1 ST.
Sales unit: 20 pieces
Lieske Part No.: 691755

E-clips, screw clamp, for screwing onto a wide range of support flanges. Dimensions (approx. dimensions) for flange thickness T: 32 - 47 mm Width B: 70 mm for threaded rod through hole: Ø 14 mm Load capacity F: 1.1 kN Material: steel, hot-dip galvanized
Sales unit: 25 pieces
Lieske Part No.: 144911

Cylinder head screw according to DIN EN ISO 1207, with slot. Can be used for: In combination with GSF 0406 for fastening the WBL... insert plates of the WSLSN... and WSLS... wide span cable ladders to anchor rails 2970 and 2971. Dimensions (approx. dimensions) Length L: 10 mm Thread: M 6 Strength class: 4.8 Material: Steel, galvanized according to DIN EN ISO 4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 402542

Cylinder head screw according to DIN EN ISO 1207, with slot. Dimensions (approx. dimensions) Length L: 16 mm Thread: M 6 Strength class: 4.8 Material: Steel, galvanized according to DIN EN ISO 4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 653110

Toothed washer. Inner Ø: 8.4 mm for thread: M 8 Material: steel, galvanized according to DIN EN ISO 4042, blue passivated
Sales unit: 100 pieces
Lieske Part No.: 537633

For fastening components to slotted tape 5050. With M4 thread.
Sales unit: 100 pieces
Lieske Part No.: 750505

Sliding nut for use with profile rail CL2008
Sales unit: 100 pieces
Lieske Part No.: 1342128

Sliding nut for use with profile rail CL2008
Lieske Part No.: 632437

Sliding nut for use with profile rail CL2008
Lieske Part No.: 630528

Sliding nut for use with profile rail CL2712
Sales unit: 100 pieces
Lieske Part No.: 1342141

Sliding nut for use with profile rail CL2712
Lieske Part No.: 1342140

Sliding nut for use with profile rail CL2712
Sales unit: 100 pieces
Lieske Part No.: 1342139

Sliding nut for use with profile rail CL2712
Sales unit: 100 pieces
Lieske Part No.: 1022342

Sliding nut for use with profile rails CM3015, CM3518 and AM3518
Lieske Part No.: 632573

Sliding nut for use with profile rails CM3015, CM3518 and AM3518
Sales unit: 100 pieces
Lieske Part No.: 1441775

Sliding nut for use with profile rails CM3015, CM3518 and AM3518
Sales unit: 100 pieces
Lieske Part No.: 632608

Sliding nut for use with profile rails CM3015, CM3518 and AM3518
Sales unit: 100 pieces
Lieske Part No.: 1342138

Sliding nut for use with profile rails CM3015, CM3518 and AM3518
Sales unit: 100 pieces
Lieske Part No.: 632639

Sliding nut for use with profile rails CM3015, CM3518 and AM3518
Sales unit: 100 pieces
Lieske Part No.: 632692

Sliding nut for use with profile rail MS4022
Sales unit: 50 pieces
Lieske Part No.: 632694

Sliding nut for use with profile rail MS4022
Lieske Part No.: 633061

Sliding nut for use with profile rail MS4022
Sales unit: 50 pieces
Lieske Part No.: 633090

Sliding nut for use with profile rail MS4022
Sales unit: 50 pieces
Lieske Part No.: 633109

Sliding nut for use with profile rail MS4022
Sales unit: 50 pieces
Lieske Part No.: 633116

Sliding nut for use with profile rail MS4022
Sales unit: 50 pieces
Lieske Part No.: 633154