MICROSENS ITU G.703 converter, single mode 1300 nm laser, 15 km,

ITU G.703 / Fiber Converter, ST connector, single-mode 1310nm, Laser 15km1 x RJ45, 2 x STThe MICROSENS MSP800 managed G.703 converter module provides remote-manageable conversion of electrical G.703 signals to fiber optic links. This module is an ideal solution for modern network infrastructures requiring flexible, open, and fiber-optic-based systems to meet increasing bandwidth demands and spatial expansion. Since G.703 signals are not standardized for fiber, this module is always used in pairs.

The MSP800 platform is a modular insertion system for 48,3 cm ( 19 inch ) racks with centralized power supply via a backplane. Modules can be freely combined to support various functions, such as multimode/singlemode conversion, wavelength conversion, bridges, or telecommunication interfaces.

Features:

• Remote management via SNMP and web interface
• Compatible with LAN, WAN, and telecommunication applications
• Flexible mounting in 48,3 cm ( 19 inch ) frames (3U for up to 12 modules) or 1U housings (for up to 3 modules)
• Supports redundant power supplies for failover protection

Technical Specifications:

• Type: Managed G.703 converter module (MSP800)
• Ports:
- 1x Fiber (depending on variant, multimode or singlemode)
- 1x TP (RJ-45) for electrical G.703 connection

• Cable Type: STP cable, 120 Ohm, RJ-45
• Fiber Type:
- Multimode: 50 or 62.5/125 μm
- Singlemode: 9/125 μm, duplex

• Data Rate: 2.048 MBit/s
• LED Indicators:
- PWR: Power on
- GLNK: Signal received on G.703 interface
- GLOS: No signal on G.703 interface
- FLNK: Fiber link intact
- FLOS: No fiber link signal
- ERR: Transmission error

• Power Supply:
- Via MSP800 backplane with individual fuse

• Environmental Conditions:
- Operating Temperature: 0 to 55 °C
- Storage Temperature: -20 to 80 °C
- Humidity: 5% to 80%, non-condensing

• Dimensions:
- Requires 1 slot in MSP800 chassis

• Management:
- Via management module MS416020-B (SNMP and web interface)


Optical Parameters:



• Multimode:
- Wavelength: 1310 nm
- Typical Power: -19 dBm
- Sensitivity: -31 dBm

• Singlemode:
- Range: 15 km, 40 km, 100 km
- Wavelengths: 1310 nm, 1550 nm
- Power: -11 to +5 dBm
- Sensitivity: -35 dBm


Installation:



• Mountable in a MICROSENS 3U rack (for 12 modules) or 1U rack (for 3 modules)
• Tabletop housing available for single module (MS417001)
• Connect converters via fiber, verify link using LEDs (FLNK, FLOS, GLNK, GLOS)
• RJ-45 connection for G.703 interface with symmetrical twisted-pair cable (120 Ohm)

Ordering Information:

• Managed Fast Ethernet Bridge Modules:
- MS416301M: Multimode ST duplex, 1310 nm
- MS416308M: Multimode SC duplex, 1310 nm
- MS416303M: Singlemode ST duplex, 1310 nm, 15 km
- MS416304M: Singlemode SC duplex, 1310 nm, 15 km
- MS416304MA: WDM Singlemode SC simplex (TX 1310 nm, RX 1550 nm)
- MS416304MB: WDM Singlemode SC simplex (TX 1550 nm, RX 1310 nm)
- MS416305M: Singlemode SC duplex, 1310 nm, 40 km
- MS416307M: Singlemode SC duplex, 1550 nm, 100 km


Applications:


The MSP800 G.703 converter module is ideal for networks with high bandwidth and range demands, particularly in telecommunications and industrial scenarios where electrical G.703 signals need to be reliably and efficiently transmitted over fiber optic links.