WAGO Terminals: Diversity, where it belongs

Terminal covers KA165 are used to increase the protection class to IP20 for MS/MO165
Sales unit: 10 pieces
Lieske Part No.: 326531

Feed-through terminal blocks with screw connection from the SNA series are available in widths from 5 mm to 36 mm. They can be snapped onto symmetrical and asymmetrical rails. They enable simple potential distribution with 3 or 4 independent connections. ABB's screw connection technology was developed to prevent the connections from coming loose due to vibrations, impacts or even accidental pulling on the cable. Thanks to the exclusive design, re-tightening the connections is no longer necessary in every case. They cover a connection requirement of 0.22 mm² to 240 mm². The screw connection technology allows up to two conductors to be connected per terminal, thus ensuring more flexibility in the control cabinet. Simple cable routing, as the conical opening guides the conductor precisely into the terminal cage.
Sales unit: 50 pieces
Lieske Part No.: 760250

FEM6 end plate 2.8mm, grey
Sales unit: 100 pieces
Lieske Part No.: 175653

M16/12.P Screw Clamp Terminal Blocks - Ground - Green-Yellow,16mm² RatedCrossSection, 12mm Spacing G32, TH 35-7.5, TH 35-15 Rail
Lieske Part No.: 988206

As an interface, interface relays connect the electronic control level, for example PLC, with the level of the sensors/actuators. They perform various functions: switching of direct or alternating voltage loads with different ohmic, inductive and capacitive components, switching in the voltage range from a few mV to 250 V, switching in the current range from a few mA to 16 A, amplifying weak control signals, potential isolation of control and load circuits and signal multiplication. The CR-P series has 9 different coil voltages with 1-2 changeover contacts. Two base variants are available: standard base and logical base. Pluggable function modules such as reverse polarity protection / freewheeling diode, LED module, RC elements, overvoltage protection or time modules expand the areas of application of the pluggable PCB relays.
Lieske Part No.: 595393

The CMS current sensors are part of the ABB energy monitoring InSite with the control units SCU100 and SCU200. The sensors measure TRMS, AC and DC currents (instantaneous, min/max and hold values) and transmit these values to the InSite control unit via a 4-pin ribbon cable.
The sensors can be used with the protection and switching devices of the ABB System pro M compact® and enable installation in the rear terminal of the protection device. The closed solid-core sensors have a high measurement accuracy of 0.5% and are less sensitive to EMC effects from adjacent final circuits.
Lieske Part No.: 875569

The CMS current sensors are part of the ABB energy monitoring InSite with the control units SCU100 and SCU200. The sensors measure TRMS, AC and DC currents (instantaneous, min/max and hold values) and transmit these values to the InSite control unit via a 4-pin ribbon cable.
The sensors can be used with the protection and switching devices of the ABB System pro M compact® and enable installation in the rear terminal of the protection device. The closed solid-core sensors have a high measurement accuracy of 0.5% and are less sensitive to EMC effects from adjacent final circuits.
Lieske Part No.: 875562

The CMS current sensors are part of the ABB energy monitoring InSite with the control units SCU100 and SCU200. The sensors measure TRMS, AC and DC currents (instantaneous, min/max and hold values) and transmit these values to the InSite control unit via a 4-pin ribbon cable.
The sensors can be used with the protection and switching devices of the ABB System pro M compact® and enable installation in the rear terminal of the protection device. The closed solid-core sensors have a high measurement accuracy of 0.5% and are less sensitive to EMC effects from adjacent final circuits.
Lieske Part No.: 875555

Direct connection V-terminal 240mm² se, for AL + CU conductor 35-185mm² sm
Lieske Part No.: 135268

Cable house connection box K12,1x3xNH2/1
Lieske Part No.: 483950

UP-frame wall frame for K3/K4, prepared for profile half cylinder
Lieske Part No.: 829720

Cable house connection box K12,2x3xNH00,2x50-185mm²,2x100A
Lieske Part No.: 253661

ZAS/STAS accessories, hood IP54 with door for 450mm h
Lieske Part No.: 275031

POWER FRAME installation frame 3-way, for installation in worktops, housing made of powder-coated sheet steel, color: white aluminum, RAL 9006, holder for socket insert, individually packed in a polybag. Please refer to the installation instructions at: www.bachmann.com/de/downloads for the dimensions.
Lieske Part No.: 769453

Blind module, accessories, polar white. 1-way blind module for support plates for MINI-COM modules.
Lieske Part No.: 996681

Endplatte für KYA02LH3, KYA02LP, KYA02KD, Farbe: grau Verkaufseinheit: 1 ST.
Lieske Part No.: 1354860

Endplatte für KYA16NH2, Farbe: blau Verkaufseinheit: 1 ST.
Lieske Part No.: 1354861

Endplatte für KYA16LH2, Farbe: grau Verkaufseinheit: 1 ST.
Lieske Part No.: 1354874

Terminal block for universal combination with the terminal rail, rail brackets and covers. Version for connecting 1 conductor Fl up to 40 x 5 mm.
Lieske Part No.: 686818

Terminals for busbars for feeding into switching devices. The terminals of the AS series enable feeding into circuit breakers (single-pole+N). Properties: for 1+N-pole MCB, load capacity up to 80 A, Eurovario system.
Lieske Part No.: 978842

FIXCONNECT-N terminal 2 x 25 mm², 8 x 4 mm², Cu for mounting on a mounting rail.
Lieske Part No.: 201407

FIXCONNECT PE and N terminal each PE/N 2 x 25 mm², 4 x 4 mm², Cu for mounting on a mounting rail.
Lieske Part No.: 589951

FIXCONNECT-PE terminal 2 x 25 mm², 8 x 4 mm², Cu for mounting on a mounting rail.
Lieske Part No.: 782872

Terminal holder for terminal type DK KL 02. Can be used in cable junction boxes DK 02..X, DK 02..XX, KF 02..X.
Sales unit: 10 pieces
Lieske Part No.: 1586220

Terminal holder for terminal type DK KL 02 and DK KL 04. Can be used in cable junction boxes DK 04..X, DK 04..XX, KF 04..X.
Sales unit: 10 pieces
Lieske Part No.: 1586206

Terminal holder for terminal type DK KL 02, DK KL 04 and DK KL 06. Can be used in cable junction boxes DK 06..X, DK 06..XX, DK 10..X, DK 10..XX, KF 06..X and KF 10..X.
Lieske Part No.: 1586218

Cover strip
for sealing unused openings equipment, 12 modules each 18 mm. Type: AS12


Quantity: 1 unit.
Lieske Part No.: 206726

Single box terminal 16mm², without mounting foot
Lieske Part No.: 304094

Main line branch terminal, 90SL, 4-pole, 80 A, 1.5-25 mm²
Lieske Part No.: 883800

Contact protection cap, universZ, 90SL, for K37N, K46N
Lieske Part No.: 458841

Control line terminal, universal Z, 7-pole, up to 6 mm², with sealing cover. Meter cabinet solution cabinet housing according to DIN VDE 0603/1, dimensional standard DIN 43 870 for surface-mounted, flush-mounted or partially recessed installation. Consists of a cabinet with door made of powder-coated, baked-in, stably profiled 1 mm thick sheet steel. Interior lining made entirely of plastic. Cable entries at the top and bottom through built-in plastic flange plates. Rear knockout in the plastic part. Busbar bushings as flanges on both sides that can be opened without tools in the lower area as a way of connecting busbars between different cabinets or in conjunction with a cable junction box and connection set. In addition to the bushing in the NAR, there are also openings in the area of the AAR (for heights 1100 and 1400 mm) and RfZ (for heights 1100 mm). Door flush with the front with internal, adjustable hinges, can be opened on the right or left with an opening angle of 110°. Door lock with cam lock. Door lock can be replaced with other locks. Cabinets can be flanged next to each other or one above the other. Cabinet size 1 to 5 fields with 72 to 540 space units (PLE). Note: The main line must be inserted into the lower connection compartment of the meter cabinet from below or from the side and connected there in accordance with VDE-AR-N 4100:2019-04. Height: __ mm (1100mm or 1400mm) Width: __ mm Depth: 205 / 160 mm, RAL color: 9010 Protection type 44, protection class II Nominal current of the busbar system 250 A Design in accordance with VDE-AR-N 4100:2019-04 Meter system for __ meter space(s). According to the technical connection conditions (TAB) of the VNB __ for: __ Electronic household meters (eHZ) or __ meters with 3-point fastening (3HZ). __ for supply systems with normal household consumption max. 63 A (10mm²) according to DIN 18015-1 (__ apartments, __ general, __ reserve, __ heat pump) __ for continuous current applications max. 32 A (10 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 22 KW) __ for continuous current applications max. 44 A (16 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 30 KW) __ for meter locations with more than 63 A in intermittent operation or 44 A in continuous operation (transformer measurement) Nominal current _ A, nominal power _ kW __ Tariff ripple control receiver as three-point version alternatively __ Tariff ripple control receiver as top-hat rail version __ Distribution panel (__ PLE), with/without busbars for feeding in __ Distribution panel (__ PLE) with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ Communication panel, 1- or 2-panel __ Communication panel with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ SLS switch Hager HTS3xxE in __ A.. Voltage tap for power supply additional devices according to VDE-AR-N 4100:2019-04: __ before the SLS with fuse box pluggable 25 kA __ before the SLS with LS switch 10 A / 25 kA __ behind the SLS with fuse box pluggable 25 kA. Surge protection with combination arrester type 1/2/3 for busbar mounting in the UAR.To comply with the requirements of DIN VDE 0100-443 and -534: ___for TNS/TT network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 315 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 315 A Fuse for cellar, washing machine, dryer (if TAB / DIN compliant) per WE (max. 6 PLE) __ pieces of FI/LS switch 10 kA, 16 A, 30 mA (ADA516D). General distribution panel equipped with: __ pcs. LS switch 6 kA, 16 A (MBS116) __ pcs. FI/LS switch 6 kA, 16 A, 30 mA (ADS916D) __ pcs. RCD type 40 A 4-pole, 30 mA (CDS440D). Consisting of: __ pcs. ZB__S, meter cabinet __ pcs. ZK__ Complete panel for __ meters __ selected make/type: HAGER/univers Z or equivalent, supply, install and connect ready for operation
Lieske Part No.: 249472

Main line branch terminal 1x35mm²-2x25 mm²(pole 1 to 3), 1x35mm²-6x25mm² (pole 4)
Lieske Part No.: 942100

Busbar terminal 6 - 70mm², for busbars 12x5mm, tier terminal
Lieske Part No.: 864872

Busbar terminal 1.5-4mm², for PE-N rail UM29A 6x6mm, for Cu conductors
Lieske Part No.: 703924

Main line terminals
Per pole with four clamping points,
solid / stranded 1.5 to 25 mm ².
stranded (with ferrule) 1.5 - 16 mm ²
Number of positions: 3-pin, finger-safe

Type: KH23C
Quantity: 1 unit.
Lieske Part No.: 236791

The main line terminals with 4 pole terminal points, solid / stranded
, 5-25 mm ². stranded (with ferrule)
, 5 -
6 mm Number of pins: 5-pin, finger-safe type: KH25C item:
ST.
Lieske Part No.: 942498

Main line branch terminal 4-pole, 2x35mm²-2x25mm² per pole, IP20, colour: grey
Lieske Part No.: 225262

Main line branch terminal 5-pole, 2x35mm²-2x25mm² per pole, IP20, 3x L, 1xPE, 1xN
Lieske Part No.: 830659

Locking pin, univers Z, for meter plug terminal
Lieske Part No.: 304140

Meter plug-in terminal, universZ, three-phase current 63 A, lockable, without TRE connection terminals. Meter plug-in terminal according to DIN VDE 0603-3, suitable for electricity meters according to DIN 43857, for the quick and safe replacement of electricity meters, nominal current: 63A, 3-pole, with 2nd connection for N conductor, terminal cross-section main line up to 25mm², color: RAL 9010, dimensions (LxWxH) = 130x40x32
Lieske Part No.: 990338

Plug pins, universZ, for meter plug terminal 100 A, 7 pieces, flexible
Lieske Part No.: 892255

Sealing cap, universal Z, for all KJ31..
Lieske Part No.: 300299

PE/N terminal, universZ, 4x5 terminal points, 2x6/2x10/1x25mm², with clamp for 25 mm². Meter cabinet solution cabinet housing according to DIN VDE 0603/1, dimensional standard DIN 43 870 for surface-mounted, flush-mounted or partially recessed installation. Consists of a cabinet with door made of powder-coated, baked-in, stably profiled 1 mm thick sheet steel. Interior lining made entirely of plastic. Cable entries at the top and bottom through built-in plastic flange plates. Back knockout in the plastic part. Busbar bushings as flanges on both sides that can be opened without tools in the lower area as a way of connecting busbars between different cabinets or in conjunction with a cable junction box and connection set. In addition to the bushing in the NAR, there are also openings in the area of the AAR (for heights of 1100 and 1400 mm) and RfZ (for heights of 1100 mm). Door flush with the front with internal, adjustable hinges, can be opened on the right or left with an opening angle of 110°. Door lock with cam lock. Door lock can be replaced with other locks. Cabinets can be flanged next to each other or one above the other. Cabinet size 1 to 5 fields with 72 to 540 space units (PLE). Note: The main line must be inserted into the lower connection compartment of the meter cabinet from below or from the side and connected there in accordance with VDE-AR-N 4100:2019-04. Height: __ mm (1100mm or 1400mm) Width: __ mm Depth: 205 / 160 mm, RAL color: 9010 Protection type 44, protection class II Nominal current of the busbar system 250 A Design in accordance with VDE-AR-N 4100:2019-04 Meter system for __ meter space(s). According to the technical connection conditions (TAB) of the VNB __ for: __ Electronic household meters (eHZ) or __ meters with 3-point fastening (3HZ). __ for supply systems with normal household consumption max. 63 A (10mm²) according to DIN 18015-1 (__ apartments, __ general, __ reserve, __ heat pump) __ for continuous current applications max. 32 A (10 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 22 KW) __ for continuous current applications max. 44 A (16 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 30 KW) __ for meter locations with more than 63 A in intermittent operation or 44 A in continuous operation (transformer measurement) Nominal current _ A, nominal power _ kW __ Tariff ripple control receiver as three-point version alternatively __ Tariff ripple control receiver as top-hat rail version __ Distribution panel (__ PLE), with/without busbars for feeding in __ Distribution panel (__ PLE) with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ Communication panel, 1- or 2-panel __ Communication panel with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ SLS switch Hager HTS3xxE in __ A.. Voltage tap for power supply additional devices according to VDE-AR-N 4100:2019-04: __ before the SLS with fuse box pluggable 25 kA __ before the SLS with LS switch 10 A / 25 kA __ behind the SLS with fuse box pluggable 25 kA. Surge protection with combination arrester type 1/2/3 for busbar mounting in the UAR.To comply with the requirements of DIN VDE 0100-443 and -534: ___for TNS/TT network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 315 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 315 A Fuse for cellar, washing machine, dryer (if TAB / DIN compliant) per WE (max. 6 PLE) __ pieces of FI/LS switch 10 kA, 16 A, 30 mA (ADA516D). General distribution panel equipped with: __ pcs. LS switch 6 kA, 16 A (MBS116) __ pcs. FI/LS switch 6 kA, 16 A, 30 mA (ADS916D) __ pcs. RCD type 40 A 4-pole, 30 mA (CDS440D). Consisting of: __ pcs. ZB__S, meter cabinet __ pcs. ZK__ Complete panel for __ meters __ selected make/type: HAGER/univers Z or equivalent, supply, install and make ready for operation.
Lieske Part No.: 645149

Snap-on PE and N terminals
For plugging onto rail 12 x 2 mm or 35 mm DIN rail
Termination: PE
Length: 75 mm
Connections: 10

Type: KM10E
Quantity: 1 unit.
Lieske Part No.: 263314

Brass terminal, NZ meter panel, N, 11 terminal points
Lieske Part No.: 121215

Brass terminal, NZ meter panel, PE, 13 terminal points
Lieske Part No.: 316570

Brass terminal, NZ meter board, N, 17 terminal points
Lieske Part No.: 815441

PE/N terminal, universal Z, 2x22 terminal points, 10x16/12x10 mm². Meter cabinet solution cabinet housing according to DIN VDE 0603/1, dimensional standard DIN 43 870 for surface-mounted, flush-mounted or partially recessed installation. Consists of a cabinet with door made of powder-coated, baked-in, stably profiled 1 mm thick sheet steel. Interior lining made entirely of plastic. Cable entries at the top and bottom through built-in plastic flange plates. Back knockout in the plastic part. Busbar bushings as flanges on both sides that can be opened without tools in the lower area as a way of connecting busbars between different cabinets or in conjunction with a cable junction box and connection set. In addition to the bushing in the NAR, there are also openings in the area of the AAR (for heights of 1100 and 1400 mm) and RfZ (for heights of 1100 mm). Door flush with the front with internal, adjustable hinges, can be opened on the right or left with an opening angle of 110°. Door lock with cam lock. Door lock can be replaced with other locks. Cabinets can be flanged next to each other or one above the other. Cabinet size 1 to 5 fields with 72 to 540 space units (PLE). Note: The main line must be inserted into the lower connection compartment of the meter cabinet from below or from the side and connected there in accordance with VDE-AR-N 4100:2019-04. Height: __ mm (1100mm or 1400mm) Width: __ mm Depth: 205 / 160 mm, RAL color: 9010 Protection type 44, protection class II Nominal current of the busbar system 250 A Design in accordance with VDE-AR-N 4100:2019-04 Meter system for __ meter space(s). According to the technical connection conditions (TAB) of the VNB __ for: __ Electronic household meters (eHZ) or __ meters with 3-point fastening (3HZ). __ for supply systems with normal household consumption max. 63 A (10mm²) according to DIN 18015-1 (__ apartments, __ general, __ reserve, __ heat pump) __ for continuous current applications max. 32 A (10 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 22 KW) __ for continuous current applications max. 44 A (16 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 30 KW) __ for meter locations with more than 63 A in intermittent operation or 44 A in continuous operation (transformer measurement) Nominal current _ A, nominal power _ kW __ Tariff ripple control receiver as three-point version alternatively __ Tariff ripple control receiver as top-hat rail version __ Distribution panel (__ PLE), with/without busbars for feeding in __ Distribution panel (__ PLE) with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ Communication panel, 1- or 2-panel __ Communication panel with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ SLS switch Hager HTS3xxE in __ A.. Voltage tap for power supply additional devices according to VDE-AR-N 4100:2019-04: __ before the SLS with fuse box pluggable 25 kA __ before the SLS with LS switch 10 A / 25 kA __ behind the SLS with fuse box pluggable 25 kA. Surge protection with combination arrester type 1/2/3 for busbar mounting in the UAR.To comply with the requirements of DIN VDE 0100-443 and -534: ___for TNS/TT network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 315 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 315 A Fuse for cellar, washing machine, dryer (if TAB / DIN compliant) per WE (max. 6 PLE) __ pieces of FI/LS switch 10 kA, 16 A, 30 mA (ADA516D). General distribution panel equipped with: __ pcs. LS switch 6 kA, 16 A (MBS116) __ pcs. FI/LS switch 6 kA, 16 A, 30 mA (ADS916D) __ pcs. RCD type 40 A 4-pole, 30 mA (CDS440D). Consisting of: __ pcs. ZB__S, meter cabinet __ pcs. ZK__ Complete panel for __ meters __ selected make/type: HAGER/univers Z or equivalent, supply, install and connect ready for operation.
Lieske Part No.: 618691

Series connection terminal 35-150mm², grey. Meter cabinet solution cabinet housing according to DIN VDE 0603/1, dimension standard DIN 43 870 for surface-mounted, flush-mounted or partially recessed installation. Consists of a cabinet with a door made of powder-coated, baked-in, stably profiled 1 mm thick sheet steel. Interior lining made entirely of plastic. Cable entries at the top and bottom through built-in plastic flange plates. Rear pre-punching in the plastic part. Busbar bushings as flanges on both sides that can be opened without tools in the lower area as a way of connecting busbars between different cabinets or in conjunction with a cable junction box and connection set. In addition to the bushing in the NAR, there are also openings in the area of the AAR (for heights 1100 and 1400 mm) and RfZ (for heights 1100 mm). Door flush with the front with internal, adjustable hinges, can be hinged on the right or left with an opening angle of 110°. Door lock with cam lock. Door lock can be replaced with other locks. Cabinets can be flanged next to each other and one above the other. Cabinet size 1 to 5 fields with 72 to 540 space units (PLE). Note: The main line must be inserted from below or from the side into the lower connection compartment of the meter cabinet and connected there in accordance with VDE-AR-N 4100:2019-04. Height: __ mm (1100mm or 1400mm) Width: __ mm Depth: 205 / 160 mm, RAL color: 9010 Protection type 44, protection class II Nominal current of the busbar system 250 A Design in accordance with VDE-AR-N 4100:2019-04 Meter system for __ meter space(s). According to the technical connection conditions (TAB) of the VNB __ for: __ Electronic household meters (eHZ) or __ meters with 3-point fastening (3HZ). __ for supply systems with normal household consumption max. 63 A (10mm²) according to DIN 18015-1 (__ apartments, __ general, __ reserve, __ heat pump) __ for continuous current applications max. 32 A (10 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 22 KW) __ for continuous current applications max. 44 A (16 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 30 KW) __ for meter locations with more than 63 A in intermittent operation or 44 A in continuous operation (transformer measurement) Nominal current _ A, nominal power _ kW __ Tariff ripple control receiver as three-point version alternatively __ Tariff ripple control receiver as top-hat rail version __ Distribution panel (__ PLE), with/without busbars for feeding in __ Distribution panel (__ PLE) with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ Communication panel, 1- or 2-panel __ Communication panel with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ SLS switch Hager HTS3xxE in __ A.. Voltage tap for power supply additional devices according to VDE-AR-N 4100:2019-04: __ before the SLS with fuse box pluggable 25 kA __ before the SLS with LS switch 10 A / 25 kA __ behind the SLS with fuse box pluggable 25 kA. Surge protection with combination arrester type 1/2/3 for busbar mounting in the UAR.To comply with the requirements of DIN VDE 0100-443 and -534: ___for TNS/TT network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 315 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 315 A Fuse for cellar, washing machine, dryer (if TAB / DIN compliant) per WE (max. 6 PLE) __ pieces of FI/LS switch 10 kA, 16 A, 30 mA (ADA516D). General distribution panel equipped with: __ pcs. LS switch 6 kA, 16 A (MBS116) __ pcs. FI/LS switch 6 kA, 16 A, 30 mA (ADS916D) __ pcs. RCD type 40 A 4-pole, 30 mA (CDS440D). Consisting of: __ pcs. ZB__S, meter cabinet __ pcs. ZK__ Complete panel for __ meters __ selected make/type: HAGER/univers Z or equivalent, supply, install and connect ready for operation.
Lieske Part No.: 341353

Series connection terminal 25-95mm², grey. Meter cabinet solution cabinet housing according to DIN VDE 0603/1, dimension standard DIN 43 870 for surface-mounted, flush-mounted or partially recessed installation. Consists of a cabinet with a door made of powder-coated, baked-in, stably profiled 1 mm thick sheet steel. Interior lining made entirely of plastic. Cable entries at the top and bottom through built-in plastic flange plates. Rear pre-punching in the plastic part. Busbar bushings as flanges on both sides that can be opened without tools in the lower area as a way of connecting busbars between different cabinets or in conjunction with a cable junction box and connection set. In addition to the bushing in the NAR, there are also openings in the area of the AAR (for heights 1100 and 1400 mm) and RfZ (for heights 1100 mm). Door flush with the front with internal, adjustable hinges, can be hinged on the right or left with an opening angle of 110°. Door lock with cam lock. Door lock can be replaced with other locks. Cabinets can be flanged next to each other and one above the other. Cabinet size 1 to 5 fields with 72 to 540 space units (PLE). Note: The main line must be inserted from below or from the side into the lower connection compartment of the meter cabinet and connected there in accordance with VDE-AR-N 4100:2019-04. Height: __ mm (1100mm or 1400mm) Width: __ mm Depth: 205 / 160 mm, RAL color: 9010 Protection type 44, protection class II Nominal current of the busbar system 250 A Design in accordance with VDE-AR-N 4100:2019-04 Meter system for __ meter space(s). According to the technical connection conditions (TAB) of the VNB __ for: __ Electronic household meters (eHZ) or __ meters with 3-point fastening (3HZ). __ for supply systems with normal household consumption max. 63 A (10mm²) according to DIN 18015-1 (__ apartments, __ general, __ reserve, __ heat pump) __ for continuous current applications max. 32 A (10 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 22 KW) __ for continuous current applications max. 44 A (16 mm²) according to VDE-AR-N 4100:2019-04 (e.g. PV up to 30 KW) __ for meter locations with more than 63 A in intermittent operation or 44 A in continuous operation (transformer measurement) Nominal current _ A, nominal power _ kW __ Tariff ripple control receiver as three-point version alternatively __ Tariff ripple control receiver as top-hat rail version __ Distribution panel (__ PLE), with/without busbars for feeding in __ Distribution panel (__ PLE) with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ Communication panel, 1- or 2-panel __ Communication panel with APZ room according to VDE-AR-N 4100:2019-04, with/without busbars for feed-in __ SLS switch Hager HTS3xxE in __ A.. Voltage tap for power supply additional devices according to VDE-AR-N 4100:2019-04: __ before the SLS with fuse box pluggable 25 kA __ before the SLS with LS switch 10 A / 25 kA __ behind the SLS with fuse box pluggable 25 kA. Surge protection with combination arrester type 1/2/3 for busbar mounting in the UAR.To comply with the requirements of DIN VDE 0100-443 and -534: ___for TNS/TT network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, without external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 160 A ___for TNS/TT network, with external lightning protection, back-up fuse in the HAK - 315 A ___for TNC network, with external lightning protection, back-up fuse in the HAK - 315 A Fuse for cellar, washing machine, dryer (if TAB / DIN compliant) per WE (max. 6 PLE) __ pieces of FI/LS switch 10 kA, 16 A, 30 mA (ADA516D). General distribution panel equipped with: __ pcs. LS switch 6 kA, 16 A (MBS116) __ pcs. FI/LS switch 6 kA, 16 A, 30 mA (ADS916D) __ pcs. RCD type 40 A 4-pole, 30 mA (CDS440D). Consisting of: __ pcs. ZB__S, meter cabinet __ pcs. ZK__ Complete panel for __ meters __ selected make/type: HAGER/univers Z or equivalent, supply, install and connect ready for operation.
Lieske Part No.: 194333