Elsner 70671, EAN: 4051996706717

Elsner 70671 built-in presence detector pure white

Security Technology > Sensors > Motion Detectors

Elsner 70671 built-in presence detector pure white

Lieske Part No. 835124
Mfg Part No 70671
EAN-Code 4051996706717
Manufacturer Elsner
Here only 186,01 EUR
221,35 EUR incl. VAT

Further information for Elsner 70671 built-in presence detector pure white

General
Housing plastic, glassplastic, glass
Colours (similar)RAL 9010 (white), RAL 9005 (black)
Dimensions (Ø × H)80mm × 36mm
Degree of protectionIP30
Weight total≈ 50 g
Ambient temperature5…+45°C
Ambient air humidity (rH) (non-condensing)5...95%
Storage temperature25...+70°C
Over voltage categoryIII
Pollution degree2
KNX bus
MediumTP1-256
Configuration modeS-Mode
Maximum group addresses254
Maximum assignments254
Communication objects252 / 122
Nominal voltage30V DC SELV
Electricity consumption≤ 10mA
Connection KNX plug-in terminal conductor diameter0.8mm s
Connection KNX plug-in terminal stripping length5mm
Time until data reception after bus voltage recovery≈ 5 s
Sensors
Detection method presence passive infrared techniquePIR
Presence detection angle≈ 94° × 82°
Presence detection range≈ 5 m
Brightness measurement range0 Lux … 2000 Lux
Temperature measurement range5…+60 °C
Humidity measurement range (rH)0...100 %
The Elsner Intra-Sewi KNX L-Pr is an in-wall presence sensor with integrated light sensor, specifically designed for use in the KNX bus system. The device detects the presence of people using passive infrared technology (PIR) and simultaneously monitors ambient lighting to enable intelligent lighting control. It is intended for installation in ceilings or walls and is particularly suitable for office and administrative rooms, where automatic lighting control is required even during low movement, such as sitting activities. The device is available in pure white (RAL 9010), with a black variant (RAL 9005) also available. The housing is made of plastic and glass, compact in design with a diameter of 80 mm and a height of 36 mm, and weighs approximately 50 g.

Applications
This presence sensor is intended for indoor use where automatic lighting control based on motion detection and light measurement is desired. It is suitable for office buildings, conference rooms, corridors, and other areas with regular foot traffic. The ambient temperature must be between 5 °C and +45 °C, and the relative humidity (non-condensing) must be between 5 % and 95 %. Storage conditions range from 25 °C to +70 °C. The IP30 protection rating protects against contact with foreign objects and splashing water, but not against direct water jets or dust, so outdoor use is not intended.

Functions and Equipment in Detail
The sensor detects people even with minimal movements, such as sitting or slight body movements, and responds with a range of approximately 5 meters and a detection angle of about 94° × 82°. Light measurement is performed in the range of 0 Lux to 2000 Lux, enabling reliable operation even in rooms with varying daylight conditions. Additionally, the sensor measures ambient temperature in the range of 5 °C to +60 °C and relative humidity from 0 % to 100 %. The threshold values for light, temperature, and humidity can be adjusted via parameters or communication objects. Configuration is performed using the KNX software ETS.

Technology Explained Simply
The device operates in S-Mode configuration mode and uses the TP1-256 bus medium. The nominal voltage is 30 V DC SELV, and the current consumption is up to 10 mA. Communication is via a KNX screw terminal connector, designed for conductors with a diameter of 0.8 mm s and a stripping length of 5 mm. After the bus voltage is restored, it takes approximately 5 seconds before data can be received. The maximum number of group addresses and assignments is 254 each, with 252 communication objects available for inputs and 122 for outputs. The overvoltage category III and pollution degree 2 indicate a robust design suitable for use in normal indoor environments.

Compatibility and Accessories
The Intra-Sewi KNX L-Pr is developed for the KNX bus system and can be integrated with other KNX devices, such as lighting control actuators, dimmers, or heating controllers, into an intelligent building automation system. The logic functions include 4 AND and 4 OR gates, each with 4 inputs. Inputs can be used as switching events or as 16 logic inputs in the form of communication objects. The outputs of the gates can be configured as either 1 bit or 2 x 8 bits. The device is designed for installation in hollow ceilings and is supplied with pre-mounted terminals. For recessed installation, a mounting ring is included, and a device box with a diameter of 60 mm and a depth of 42 mm is required separately.

Installation and Mounting
Installation is carried out by mounting into a hollow ceiling or a suitable recessed installation solution. The pre-mounted terminals simplify wiring, with connection terminals designed for conductors of 0.8 mm s and a stripping length of 5 mm. The installation instructions are available in multiple languages (German, English, French, Italian, Spanish) and support correct installation. Configuration is performed via the KNX software ETS, allowing individual adjustment of parameters such as light thresholds, logic functions, and group addresses.

Operational Advantages
The use of the presence and light sensor enables efficient energy savings through automatic switching off of lighting when no people are present or when ambient lighting is sufficient. The integrated logic functions allow complex control sequences that can be adapted to the specific requirements of the room. The high reliability in motion detection, even during low activity, ensures uninterrupted operation. Communication via the KNX system ensures flexible integration into existing building automation systems.

Scope of Delivery
The device is supplied with pre-mounted terminals for hollow ceiling installation, a mounting ring for recessed installation, installation instructions (in German, English, French, Italian, Spanish), and a manual (available as download). The product file is also available as a download.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/835124
qrcode für Elsner 70671 built-in presence detector pure white