Elsner 70669, EAN: 4051996706694

Elsner 70669 indoor sensor temperature/humidity pure white

Elsner 70669 indoor sensor temperature/humidity pure white

Lieske Part No. 1343855
Mfg Part No 70669
EAN-Code 4051996706694
Manufacturer Elsner
Here only 178,84 EUR
212,82 EUR incl. VAT

Further information for Elsner 70669 indoor sensor temperature/humidity pure white

General
Housingplastic, glass
Colourssimilar to pure white RAL 9010, similar to deep black RAL 9005
Mountinginstallation in hollow ceiling or device box
Dimensions Ø × mounting depthca. 80 mm x ca. 5 mm; mounting depth ca. 31 mm (including terminals)
Degree of protectionIP 30
Weightca. 50 g
Ambient temperature20…+60°C
Ambient air humidity5...95% rH, non-condensing
Storage temperature30…+70°C
KNX bus
KNX mediumTP1-256
Configuration modeS-Mode
Group addressesmax. 254
Assignmentsmax. 254
Communication objectsIntra-Sewi KNX TH: 183, Intra-Sewi KNX T: 129
Nominal voltage KNX30 V DC SELV
Power consumption KNXmax. 10 mA
ConnectionKNX plug-in terminals
Time until data reception after bus voltage recoveryapprox. 5 seconds
Sensors
Temperature measurement range20°C … +60°C
Humidity measurement range0% rF … 100% rF
The Elsner Intra-Sewi KNX TH is an in-wall sensor for measuring room temperature and relative humidity in the KNX building bus system. It is available in the pure white RAL 9010 finish and is used for decentralized monitoring of ambient conditions in indoor spaces. The device is designed for mounting in hollow ceilings or into a device box and features a housing made of plastic and glass. The installation depth is approximately 31 mm, including pre-mounted terminals, while the protrusion depth is about 5 mm. The protection rating IP 30 ensures protection against solid foreign objects and splashing water, but not against dust or prolonged moisture. The operating environment ranges from 20 °C to +60 °C at a humidity of 5 to 95 % rH, non-condensing. The storage temperature is 30 °C to +70 °C. The device weighs approximately 50 g.

Applications

The sensor is used in buildings with KNX installations to monitor and control room climate conditions. It is suitable for residential and office buildings where intelligent climate control is implemented via the KNX system. The measured values are used to control heating, cooling, and ventilation systems to ensure a comfortable indoor climate. The dew point calculation function supports the prevention of condensation, especially in rooms with high humidity.

Functions and Equipment in Detail

The Intra-Sewi KNX TH measures temperature in the range of 20 °C to +60 °C and relative humidity from 0 % to 100 % rH. The internal sensors can be combined with external values, with the proportion of internal and external measurements being adjustable in percentage terms. This enables the calculation of mixed values, for example, for room averages. The limit values for temperature and humidity are configurable via parameters or communication objects. The device features an integrated PI controller for heating and cooling, which operates based on temperature values and supports both single- and two-stage control. A second PI controller controls ventilation based on humidity, allowing exhaust and supply ventilation to be implemented as single-stage or exhaust ventilation as single- or two-stage. The bus notification function indicates whether the measured values lie within the comfort zone according to DIN 1946.

Technology Explained Simply

Communication takes place over the KNX network via medium TP1-256. The sensor operates in configuration mode S-Mode and supports up to 254 group addresses and 254 assignments. The nominal voltage is 30 V DC SELV, with a maximum current draw of 10 mA. Data transmission occurs via KNX plug-in terminals. After the bus voltage is restored, it takes approximately 5 seconds for data to be received. Configuration is performed using the KNX software ETS. Communication objects include 183 for the Intra-Sewi KNX TH and 129 for the Intra-Sewi KNX T. Logic functions include 4 AND and 4 OR gates, each with 4 inputs, which can be assigned to switching events or communication objects. The gate outputs can be configured as either 1 bit or 2 x 8 bits. Two setpoint comparators enable the output of minimum, maximum, or average values from up to five received values.

Compatibility and Accessories

The sensor is designed for the KNX system and requires a KNX installation. The pre-mounted terminals facilitate installation in hollow ceilings. For installation in a device box, a mounting ring is included. Configuration is done via the ETS software. The delivery includes the sensor, pre-mounted terminals, mounting ring, installation instructions in multiple languages (German, English, French, Italian, Spanish), as well as a manual and product file available for download.

Mounting and Installation

Mounting is either into a hollow ceiling or into a device box. The pre-mounted terminals facilitate installation in hollow ceilings. The mounting ring is intended for installation into a device box. Installation is carried out according to the instructions in the installation manual. Power supply is via the KNX bus network (PoE, power supply through the network cable). Configuration is performed using the ETS software.

Operational Advantages

The sensor enables precise and flexible control of room climate systems. The integrated logic functions and controllers reduce the need for additional control devices. The mixed value calculation allows the use of multiple sensors for a representative room representation. The bus notification according to DIN 1946 supports compliance with comfort criteria. Configuration via ETS is standardized and enables easy integration into existing KNX systems.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/1343855
qrcode für Elsner 70669 indoor sensor temperature/humidity pure white