| Power supply |
| Voltage | 11…28 V DC SELV |
| Electricity consumption | ≤ 35 mA |
| Connection terminal block conductor diameter stripping length | Ø 0.8 mm s, 5 mm |
| Sensors |
| Temperature measurement range | 5…+60°C |
| Humidity measurement range | 0...95 % |
| Technical data |
| Housing | Real glass, plastic |
| Colours | white [RAL 9010] |
| Mounting | on device box according to DIN EN IEC 60670-1 |
| Degree of protection | IP 20 |
| Housing dimensions (W × H) | 55 mm × 55 mm |
| Depth dimensions | 8 mm |
| Dimensions of mounting ring (W × H) | 71 mm × 71 mm |
| Weight total | ca. 50 g |
| Ambient temperature | 5…+45 °C |
| rF (relative humidity) non-condensing | 0...95 % |
| Storage temperature | 25...+70 °C |
| Over voltage category | III |
| Pollution degree | 2 |
| Wireless |
| Frequency range | 868.0...868.6 MHz |
| Transmitting power | max. 25 mW |
The Elsner indoor sensor WGTH gl, type 20557, is a wireless sensor for measuring room temperature and relative humidity. It is specifically designed for use with control systems WS1 Color/Style, WS1000 Color/Style/Connect, and Solexa II (temperature evaluation only). The device transmits measured values wirelessly in the frequency range of 868.0 to 868.6 MHz, with a maximum transmission power of 25 mW. Power supply is via 11 to 28 V DC SELV, with a maximum current consumption of 35 mA. The connection terminal is designed for conductors with a diameter of 0.8 mm s and a stripping length of 5 mm.
Wireless indoor sensor for temperature and humidity
The sensor is designed for indoor use and measures temperature in the range of 5 to +60 °C and relative humidity from 0 to 95 %, with the condition that humidity must not be condensing. The measured values are transmitted to the corresponding control system, and multiple WGTH gl sensors can be registered to a single control system. Registration is performed according to the instructions in the respective control system’s manual. The wireless connection operates in the 868 MHz frequency band, commonly used for decentralized building automation systems in Germany and Europe.
The sensor is suitable for building automation systems, particularly in residential and office buildings, where precise monitoring of room climate conditions is required. It is used in conjunction with the mentioned control systems to adjust heating or ventilation systems according to actual room conditions. Compatibility with WS1 and WS1000 systems allows integration into existing KNX or multifunction control environments. Use in combination with Solexa II is limited to temperature evaluation only.
The device consists of a housing made of real glass and plastic, finished in pure white (RAL 9010). The surface is smooth and visually integrates into modern indoor installations. The sensor is mounted on a device box that must comply with DIN EN IEC 60670-1. The housing itself has a width and height of 55 mm, the projection depth is 8 mm, and the mounting ring measures 71 mm × 71 mm. The total weight of the sensor is approximately 50 g.
Wireless transmission occurs in the 868 MHz band, used for license-free wireless communication in building automation. The maximum transmission power of 25 mW provides sufficient range in indoor environments, although the exact range depends on the surrounding conditions. The power supply voltage of 11 to 28 V DC SELV is safety-compliant and can be drawn, for example, from the control system’s connection plate, provided it has a multifunction input. The current consumption of ≤ 35 mA is low and does not significantly burden the power source.
The sensor is compatible with control systems WS1 Color/Style, WS1000 Color/Style/Connec, and Solexa II. Integration is achieved wirelessly, with the control system receiving and processing sensor data. As accessory, a frame is included in the delivery scope, which can optionally be replaced by a frame from the switch series used in the building. This allows optical harmonization with existing switch elements.
Installation is performed on a device box complying with DIN EN IEC 60670-1. The sensor is mounted onto the box using the carrier plate and frame. Installation does not require special tools, although preparation of the device box is necessary. The connection terminal is designed for conductors with a diameter of 0.8 mm s and a stripping length of 5 mm. Power supply is provided via the specified voltage, which can be supplied by the control system or a separate power supply unit.
The sensor provides reliable and precise measurement of temperature and humidity in indoor environments. Wireless transmission enables flexible installation without cabling between sensor and control system. Low current consumption and SELV power supply enhance safety. Compatibility with various control systems facilitates integration into existing building automation environments. The optical design in pure white (RAL 9010) blends into modern interiors, and the frame can optionally be replaced to match the building’s switch series.
The sensor has a protection rating of IP 20, meaning it is protected against contact with fingers and against solid foreign objects, but not against water or dust. The ambient temperature must be between 5 and +45 °C, and relative humidity may reach 95 %, provided no condensation occurs. Storage temperature ranges from 25 to +70 °C. Overvoltage category III and pollution degree 2 meet requirements for indoor installations with normal pollution.
The delivery scope includes the housing, carrier plate, frame, and a datasheet with installation instructions in German, English, French, Italian, and Spanish.
Wireless indoor sensor,
temperature measurement range,
humidity measurement range,
frequency range,
SELV,
IP 20