Further information for Dold 0061573 semiconductor contactor AC24-115V AC25A
Technical data
Analog Input Control
4 - 20 mA
Approvals
UL
Load current up to
50 A
Load voltage up to
AC 480 V
Number of poles
1-pole
Width
22,5 mm, 45 mm, 90 mm
Type
BF 9250/0_2
Temperature monitoring
Variant
Auxiliary voltage
AC/DC 24 V
Contact equipping
without signal contact
Control input
DC 0 - 10 V
Load current
AC 25 A
Load voltage
AC 24 - 115 V
Semiconductor output
1-pole
Approvals and Markings
UL-listed C/US
Variant
Self optimising, to achieve as short as possible control periods, suitable for infrared lamps
The Dold semiconductor contactor BF9250.91/042 UH=AC/DC24V DC0-10V is a semiconductor contactor with an analog control input for pulse packet control of heating elements. It is used for precise temperature control in industrial applications, particularly for loads such as infrared lamps, where fast and noiseless switching is required. The device is zero-voltage switching, meaning current flow occurs only at the zero crossing of the AC voltage to minimize electrical interference and sparking. Control is achieved via an analog input, which can be operated either as voltage (DC 0–10 V) or current (DC 4–20 mA). The self-optimizing pulse distribution enables minimized cycle times and particularly precise control, especially for dynamic loads such as infrared heaters.
Applications include industrial process control, particularly in manufacturing, packaging technology, and drying technology, where precise temperature control is required. The device is designed for ohmic loads such as heating strips, heating ovens, or infrared lamps, and is suitable for operating voltages up to AC 480 V and load currents up to AC 50 A. The rated load voltage for this type is AC 24–115 V at a load current of AC 25 A. The auxiliary voltage is AC/DC 24 V, with a current consumption of less than 26 mA.
Functions and equipment in detail include an integrated temperature protection function for the power semiconductor, which indicates an overtemperature condition via a red LED and ensures safe operation. The varistor protection circuit protects the device against voltage surges. The LED indicators signal the operating status: green LED for power supply, yellow LED for output status, and red LED for faults such as synchronization errors, control input errors, or overtemperature. Some messages are latched, with the overtemperature message only resettable by briefly switching off the power supply.
Technology explained simply is based on pulse packet control, where the load is switched on in short, controlled pulses to control average power. The self-optimization dynamically adjusts the pulse distribution to minimize cycle times and enable faster response to load changes. The zero-crossing detection ensures the switch only operates at the zero crossing of the mains voltage, increasing lifespan and reducing interference. The output control resolution is 5 %, sufficient for fine control. The residual current in the off state is 1.0 mA, typical for semiconductor contactors.
Compatibility and accessories refer to use with DIN rail (35 mm), with the width varying according to rated current: 22.5 mm for 10 A, 45 mm for 25 A, and 90 mm for 50 A. The device is compliant with IEC/EN 60947-4-2 and IEC/EN 60947-4-3 and carries the UL-listed C/US approval, enabling use in North America. The control inputs are flexible and can also be operated inverted, which may be necessary for certain control systems.
Mounting and installation is done by clipping onto a DIN rail. Recommended clearances are 20 mm above and below the cable duct and 10 mm to the right and left to ensure sufficient cooling. The operating temperature range is 0 °C to 40 °C, with current derating at higher temperatures (e.g. 0.4 A/°C above 40 °C for 25 A). Maximum relative humidity is 75 % without condensation.
Operational advantages include noiseless and fast switching, high lifespan due to semiconductor technology, and precise temperature control. Integrated protection functions such as temperature protection and varistor protection increase reliability. The LED indicators enable quick fault diagnosis. The device is designed for continuous operation and is suitable for industrial applications with high demands on stability and accuracy.