Further information for Dold 0050068 overcurrent relay AC220-240V 1-10A
Technical data
1- / 3-phase
1
Enclosure design
Distribution board
Output contacts
1 C/O contact
Width
17,5 mm
Type
IK 9272
Operate delay
Variant
Auxiliary voltage
AC 220 - 240 V
Contact equipping
1 changeover contact
Measuring range
1 - 10 A
Switching delay
0,1 - 20 s
Variant
1-phasiges Stromrelais. Arbeitsstromprinzip. Nicht speichernd
The Dold overcurrent relay IK9272.11/010 AC220-240V 1-10A is a single-phase current relay for monitoring alternating and three-phase power networks. It is designed for continuous monitoring of load currents in the range of 1 to 10 A and responds to exceeding the set switching point with a time-delayed switching function. The device operates on the operating current principle, whereby the output relay is activated in the event of a fault, and is not designed to be latching. The auxiliary voltage is AC 220 to 240 V, with the operating voltage functioning stably within a range of 0.8 to 1.1 times the nominal voltage. The width of 17.5 mm allows for compact mounting in installation distributors according to DIN 43880.
Applications
This relay is intended for use in industrial and technical installations where precise current monitoring is required. Typical applications include monitoring motors, heaters, pumps, or other electrical consumers, where a sudden increase in current may indicate a fault or overload. The adjustable switching delay of 0.1 to 20 seconds allows for consideration of short-term current peaks that should not be interpreted as faults. The device type IK 9272 is designed for installation distributors, with connection terminals located at the bottom and a depth of 59 mm.
Functions and Equipment in Detail
The relay features an adjustable switching point within the measurement range of 1 to 10 A, which can be continuously adjusted. The hysteresis is fixed at approximately 4%, ensuring stable switching behavior without unwanted oscillations. The output contacts consist of a changeover contact (1 C/O contact), designed for switching operations with an electrical life of up to 300,000 switching cycles at 1 A and AC 230 V. The mechanical life exceeds 100 million switching cycles. Operational readiness is indicated by a green LED, while a yellow LED signals the switching state of the output relay.
Technology Explained Simply
Monitoring is performed via the measured current, supplied through the input terminals. When the set switching point is exceeded, the contact is switched after the set delay time has elapsed. The delay is intended to ignore short-term current peaks, such as those occurring during motor start-ups. The auxiliary voltage is supplied via the network and provides the necessary energy for controlling the output relay. The switching delay is adjustable via a rotary control on the device and can be varied between 0.1 and 20 seconds depending on the application.
Compatibility and Accessories
The device is specified according to IEC/EN 60255 and complies with standards for electrical equipment in monitoring technology. It is designed for continuous operation and can be operated in environments with temperatures from -20 to +60 °C. The terminals are rated for conductor cross-sections of 2 x 2.5 mm² (solid) or 2 x 1.5 mm² (stranded wire with ferrule DIN 46228-1/-2/-3/-4). Mounting is done via a DIN rail according to IEC/EN 60715. The enclosure protection rating is IP 40, and the terminals are rated IP 20. Maximum short-circuit withstand is ensured by a maximum fuse rating of 4 A gG/gL.
Mounting and Installation
Mounting is performed in standard installation distributors with DIN rail. The connection terminals are located at the bottom of the device, enabling easy integration into existing control systems. Fixing is done using flat clamps with self-lifting connection washers, with a tightening torque of 0.8 Nm. The device dimensions are 17.5 mm (width) x 90 mm (height) x 59 mm (depth). Installation requires no special tools, as the terminals are mounted directly onto the DIN rail.
Advantages in Operation
The adjustable switching delay allows flexible adaptation to different load profiles. The LED indicators provide quick visual control of the operating status. The high mechanical life and robust construction ensure reliable operation over a long period. Compliance with the IEC/EN 60255 standard ensures compatibility with other devices in the network. The device is designed for use in industrial environments where high reliability and longevity are required.