Further information for ABB Automation SU202M-C1 circuit breaker 2P 1A
General
Release characteristic
C
Number of poles (total)
2
Number of protected poles
2
Rated current
1
Rated voltage
440
Rated insulation voltage Ui
400
Rated impulse withstand voltage Uimp
4
Voltage type
AC/DC
Frequency
60
Current limiting class
3
Over voltage category
3
Pollution degree
3
Width in number of modular spacings
2
Built-in depth
69
Degree of protection (IP)
IP20
Ambient temperature during operating
55
Connectable conductor cross section multi-wired
25
Connectable conductor cross section solid-core
35
Power loss
2.8
Concurrently switching N-neutral
Additional equipment possible
Explosion-proof
Flush-mounted installation
The SU202M-C1 circuit breaker from ABB is a two-pole circuit protection switch for use in electrical installations. It protects cables and conductors against overload and short circuit in accordance with standards DIN VDE 0100-430 and DIN VDE 0100-530. The device complies with construction regulations DIN VDE 0660-101 as well as international standards IEC/EN60947-2, UL489 and CSA 22.2 No. 5, enabling worldwide use in various markets. The C tripping characteristic ensures appropriate response to load fluctuations and short circuits in typical consumer systems.
Applications
This circuit breaker is designed for use in low-voltage installations, particularly in residential and commercial buildings as well as industrial facilities with low to medium loads. It is rated for a nominal voltage of 440 V and a nominal insulation voltage Ui of 400 V. The nominal impulse voltage withstand is 4 kV, providing sufficient insulation strength for typical operating conditions. The overvoltage category 3 and pollution degree 3 make the device suitable for environments with moderate pollution risk, for example, indoor spaces with normal air pollution.
Functions and Equipment in Detail
The device features a patented connection terminal that enables simple and secure contact. Mounting is done using a pressure plate, ensuring a reliable connection even with frequent installation and removal. The cable entry opening is positioned above the phase bar entry opening, providing better visibility during wiring. The connection terminal allows direct connection of conductors with a cross-section up to 35 mm² (single-strand) or 25 mm² (multi-strand), with insulation integrated into the device. The protection class IP20 protects against contact with solid objects larger than 12.5 mm and against splashing water, but not against dust or general dampness – suitable for indoor use.
Technology Explained Simply
The circuit breaker is rated for a nominal current of 1 A, making it suitable for small consumers or control circuits. The energy limitation class 3 means that the device releases limited energy during a short circuit, reducing stress on the installation. The frequency specification of 60 Hz refers to the operating voltage in alternating current systems, particularly in regions with 60 Hz mains voltage. The maximum ambient temperature during operation is 55 °C, defining the operating limit in warm environments. The power loss of 2.8 W is a measure of heat generation during operation, which should be considered when planning heat dissipation.
Compatibility and Accessories
The device can be combined with various accessories to meet specific requirements. These include the series terminals CMS-101PS and CMS-102PS, which enable secure connections in series mounting. Additionally, the operating current tripping unit S2C-A1U with a voltage range of 12 to 60 V is available, suitable for special switching functions in control systems. Combining the device with these accessories extends its functionality in complex installations.
Mounting and Installation
The circuit breaker is designed for installation in standard distribution boxes. The mounting depth is 69 mm, and the width corresponds to two module units, enabling compact placement in standard switchboards. Mounting requires no additional tools, as the pressure plate securely fixes the terminal. Flush mounting is not intended; the device is exclusively designed for surface or switchboard mounting.
Advantages in Operation
The combination of international approvals (UL489, CSA 22.2 No. 5, IEC/EN60947-2) enables flexible use in various markets. The patented connection terminal reduces installation time and increases connection reliability. The direct connection capability for conductors up to 35 mm² (single-strand) reduces the need for additional transition terminals. Intensive quality tests performed before shipment ensure high operational safety and long service life of the device.