Gustav Hensel 6100230, EAN: 4012591622307

Gustav Hensel KV 3554 Distribution Enclosure IP54

Installation > Distributor Cabinets > ISO - Distributor / housing, moisture

Gustav Hensel KV 3554 Distribution Enclosure IP54

Lieske Part No. 252588
Mfg Part No 6100230
EAN-Code 4012591622307
Manufacturer Gustav Hensel
Here only 248,61 EUR
295,85 EUR incl. VAT

Further information for Gustav Hensel KV 3554 Distribution Enclosure IP54

General
Degree of protectionIP54
Rated voltage400 V
Rated insulation voltage690 V a.c.
Protection classII
Rated current of clamp75 A
Maximum device rated current63 A
Number of division units54 TE
Number of rows3
Conduit spacing150 mm
Cable glandElastic sealing membranes, metric pre-threads M20
Sealing range7 mm - 29 mm
Cable entry positiontop and bottom
MaterialPolystyrene
Filament test750 °C
UL 94V-2
Temperature resistance-25 to +80 °C
Nominal power50 W
Temperature difference30 K
Number of terminals per pole32 push-in terminals, 8 screw terminals
Conductor cross-section plug terminal1.5 to 4 mm²
Conductor cross-section screw terminal1.5 to 25 mm²
Conductor typeSolid, fine-stranded, stranded
Conductor materialCopper
Compliance with standardsDIN EN 60670-1, DIN EN 60670-24
Halogen freeYes
Silicone-freeYes
The Gustav Hensel small distribution board type KV 3554 is an automation housing made of high-quality thermoplastic (polystyrene), designed for surface-mounted applications in buildings or for protected outdoor installations. The housing offers a total of 54 mounting units (TE), distributed across three rows with 18 TE each, and is thus designed for mounting devices with snap-fastening on DIN support rails. The support rail spacing is 150 mm, ensuring compliance with the DIN 43880 standard. The integrated cable entry is achieved via elastic sealing membranes, enabling a watertight and dust-tight seal. The protection rating IP 54 safeguards the enclosure against dust and splashing water, making it suitable for outdoor use, provided the area is protected. The transparent door allows visual inspection of installed devices without opening the enclosure. An integrated accessory compartment and cover strips for the device cutout are also part of the housing. The cable entry panel ensures orderly cable routing and prevents unintended contamination.

Applications
The small distribution board is intended for use in buildings and protected outdoor areas, where installation is carried out on a wall or in a niche. The ambient temperature must range between -5 °C and +40 °C, with the maximum temperature over 24 hours not exceeding 35 °C. The relative humidity is up to 50 % at 40 °C and up to 100 % at 25 °C. At high temperatures and direct sunlight, the effects on installed equipment should be considered, particularly regarding condensation formation. The specifications for ambient temperature and humidity are crucial for the reliability of installed devices.

Functions and Equipment in Detail
The housing features a FIXCONNECT® terminal for N and PE conductors, ensuring a secure and reliable connection. The rated current of the terminal is 75 A, with devices installed in the housing allowed to have a maximum rated current of 63 A. The rated voltage is 400 V, and the rated insulation voltage is 690 V a.c. Protection class II ensures a double-insulated design, eliminating the need for additional earthing. The terminals are designed for various conductor cross-sections: push-in terminals for 1.5 mm² to 4 mm², screw terminals for 1.5 mm² to 25 mm², with the maximum number of conductors per terminal point varying by type. Cables can be introduced via metric pre-punchings M20 or elastic sealing membranes, with sealing ranges from 7 mm to 29 mm. The cable entry positions are located at the top and bottom of the housing wall.

Technology Explained Simply
The elastic sealing membranes ensure a tight seal of the cable openings, keeping dust and splashing water away from the interior of the enclosure. The IP protection rating IP 54 means the housing is dust-tight and protected against splashing water from all directions. The material polystyrene is halogen-free, silicone-free, and has a temperature resistance from -25 °C to +80 °C. The glow wire test according to IEC 60695-2-11 is 750 °C, confirming the fire protection quality of the material. The UL 94 classification V-2 indicates that the material exhibits limited flame spread in case of fire.

Compatibility and Accessories
Various accessories are available for this small distribution board, facilitating installation and operation. These include the Hensel AKM 20 mounting cable gland IP67 with glow wire test IEC 960°C, the Hensel STM 20 step gland IP55 M20 for metric pre-punching M20 with sealing range D=5-16 mm, the Hensel KV ES1 mounting lock for KV automation housings 12-54TE, and the Hensel ESM 20 insert gland IP55 M20 grey for metric pre-punching M20. These components can be used as required to extend functionality or enhance safety.

Installation and Mounting
Mounting is carried out on a wall or in a niche, with the DIN support rail included in the delivery scope. The support rail spacing of 150 mm allows for mounting of standard devices. Cables are introduced through the designated openings using elastic sealing membranes or metric pre-punchings M20. The transparent door is secured with an integrated locking mechanism. Cover strips and labeling strips facilitate identification and proper completion of the installation.

Operational Advantages
The small distribution board offers high mechanical and electrical reliability. The integrated sealing membranes and IP 54 protection rating ensure a long service life even under demanding environmental conditions. The transparent door enables quick visual inspection of devices without opening the enclosure. The FIXCONNECT® terminals ensure a secure and durable connection of the conductors. The halogen-free and silicone-free material composition reduces fire hazard and protects the environment in case of fire.

The housing dimensions are 630 mm (height) × 403 mm (width) × 129 mm (depth). The net weight is 4.594 kg. Conformity with standards is ensured according to DIN EN 60670-1 and DIN EN 60670-24. Certification is carried out according to IEC 61439-3. The product number is 6100230, the EAN number is 4012591622307. The ETIM class is EC000214 – Small distribution board.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/252588
qrcode für Gustav Hensel KV 3554 Distribution Enclosure IP54