| General |
| Degree of protection | not specified |
| Operating voltage | 12..230 V UC |
| Switching power normally open contact (NO) | 16 A/250V AC |
| Switching power normally closed contact (NC) | 10 A/250V AC |
| LED lamp power | 200 W |
| Incandescent lamp power | 2000 W |
| Drive indicator | LED |
| Freewheeling/Clamping diode | Integrated |
| Relay type | Bistable |
| Mounting | DIN-EN 60715 TH35 |
| Pitch unit | 1 |
| Switching noise | low |
| Stand-by loss | none |
| Control | potential-free |
| Technology | Hybrid technology |
The Eltako switching/control relay ER12-002-UC is a rail-mounted device for installation on a support rail in accordance with DIN-EN 60715 TH35. It features two potential-free changeover contacts and is designed for use in electrical installations where reliable and energy-efficient switching functionality is required. The hybrid technology combines the advantages of a wear-free electronic actuation with the high switching capacity of special relays. Due to the use of a bistable relay, no coil power loss occurs in the switched-on state, resulting in low heating and reduced energy consumption. The electronics are only activated when the control contact is closed, thus avoiding standby losses.
Applications
This relay is suitable for use in residential and commercial buildings, particularly in systems requiring remote control or automated switching logic. It can be used to control lighting systems, heating, blinds, or other electrical loads. The switching capacity for the make contact is 16 A/250 V AC, enabling operation of 230-V LED lamps up to 200 W and incandescent lamps up to 2000 W. The break contact has a rated capacity of 10 A/250 V AC and is also designed for 230-V LED lamps up to 200 W and incandescent lamps up to 2000 W. The application is in electrical circuits requiring potential-free control, for example in alarm systems, lighting controls, or integration into building management systems.
Functions and equipment in detail
The device features a control indication with an LED that visually signals the control status. The integrated freewheeling/braking diode (A1 = +, A2 = –) protects the control electronics from inductive voltage spikes that may occur when switching inductive loads. The relay can be mounted in any position (open or closed) during commissioning and automatically synchronizes upon first actuation. This simplifies installation and reduces error susceptibility. The switching noise is low, making the device suitable for applications in quiet environments.
Technology explained simply
The hybrid technology of the relay combines electronic control with a mechanical relay. The microcontroller is only activated when the control contact is closed, thereby increasing energy efficiency. The bistable relay remains in the position it has taken, without requiring continuous power supply. When the control contact is opened or the control voltage drops, the relay automatically resets. The potential-free circuit enables flexible integration into existing control and switching circuits without requiring galvanic isolation or additional voltage sources.
Compatibility and accessories
The relay is not suitable for feedback with the switching voltage of a dimmer switch. For such applications, special relays such as models ESR12DDX-UC, ESR12NP-230V+UC, or ESR61NP-230V+UC are intended. The universal control voltage of 12 to 230 V UC allows use with various control sources, such as push buttons, sensors, or transmission units. Installation is on a DIN support rail, with the device having a width of 18 mm (1 module unit) and a depth of 58 mm.
Mounting and installation
Mounting is on a support rail in accordance with DIN-EN 60715 TH35. The device is designed for installation in enclosures or electrical installations. Wiring is done via the designated connection terminals. The potential-free circuit requires no special insulation between the control and load circuits. Installation is typically performed by qualified electricians who comply with the regulations of electrical standards (e.g. VDE 0100).
Advantages in operation
The relay is characterized by high reliability and long service life. The low power loss and lack of heating in the switched-on state reduce stress on the installation. The low switching noise makes the device suitable for applications in residential and office buildings. The potential-free circuit enables flexible integration into existing systems. The control indication with LED facilitates diagnosis and maintenance.