Elsner 71512, EAN: 4051996715221

Elsner 71512 room temperature controller deep black

Elsner 71512 room temperature controller deep black

Lieske Part No. 2035925
Mfg Part No 71512
EAN-Code 4051996715221
Manufacturer Elsner
Here only 94,10 EUR
111,98 EUR incl. VAT

Further information for Elsner 71512 room temperature controller deep black

General
HousingReal glass, plastic
Colours (similar)RAL 9003 (white), RAL 9005 (black)
Degree of protectionIP20
Dimensions (W × H)81,5 mm × 81,5 mm
Installation depth12,5 mm
Weight total≈ 70 g
Ambient temperature5…+45 °C
rF (relative humidity) non-condensing0...95 %
Storage temperature25...+70 °C
Over voltage categoryIII
Pollution degree2
KNX bus
MediumTP1-256
Configuration modeS-Mode
Maximum group addresses500
Maximum assignments500
Communication objects147
Nominal voltage30 V DC SELV
Electricity consumption≤ 23 mA
ConnectionKNX plug-in terminal
Conductor diameterØ 0,6...0,8 mm s
Strip length5 mm
Time until data reception after bus voltage recovery≈ 5 s
Sensor
Temperature measurement range5…+60 °C
Humidity measurement range0...100 %
The room temperature controller eTR 103 AC KNX sec from Elsner is a control device for KNX building bus systems, specifically designed for controlling VRF climate units (Variable Refrigerant Flow). The device features an integrated temperature controller and allows manual adjustment of various room climate parameters via touch-sensitive control surfaces. Users can adjust the set temperature using touch buttons +/–, select fan speed between 1 and 3, and switch the operating mode between heating, cooling, dehumidifying, and humidifying. Additionally, the operation can be switched between automatic and manual mode, and the temperature controller can be activated or deactivated using an ON/OFF button. The current settings are displayed via dimmable LEDs.

Applications

The controller is intended for controlling climate units in summer operation and can simultaneously be used to control a KNX heating actuator in winter operation. It is therefore suitable for year-round climate control systems that include both cooling and heating functions. The integrated sensors measure room temperature in the range of 5 to +60 °C and relative humidity from 0 to 100 %, with the measured values being usable for control. Control is performed via a PI controller, configurable for heating, cooling, dehumidifying (single- or two-stage), and humidifying (single-stage). Special parameters for VRF systems are integrated into the device to ensure optimal control via KNX interfaces or gateways.

Functions and Equipment in Detail

The device has two inputs, to which either binary contacts such as push buttons or window contacts or analog temperature sensors of type T-NTC can be connected. The integrated AND and OR logic gates enable the linking of communication objects to realize complex control logics. Control can be based on the integrated temperature or humidity sensor, and mixed values from internal and external measurements can also be formed. The current settings are displayed via dimmable LEDs, which visually indicate the operating states.

Technology Explained Simply

The controller operates in the KNX network via the medium TP1-256 and supports the configuration mode S-Mode. Communication takes place via a KNX plug-in terminal, designed for conductors with a diameter of 0.6 to 0.8 mm s. The stripping length is 5 mm. The nominal voltage of the device is 30 V DC SELV, and the maximum current consumption is 23 mA. After the bus voltage returns, it takes approximately 5 seconds for the device to receive data again. The maximum number of group addresses and assignments is 500 each, and the device supports 147 communication objects. The protection rating IP20 safeguards the device against finger contact and against solid foreign objects, but not against splashing water or dust. The ambient temperature must be between 5 and +45 °C, and the relative humidity may reach up to 95 %, provided no condensation occurs. The storage temperature is between 25 and +70 °C. The overvoltage category III and pollution degree 2 meet the requirements for installations in indoor environments with normal pollution.

Compatibility and Accessories

The device is designed for use with VRF climate systems and can be connected via KNX interfaces or gateways. Optionally, an external temperature sensor T-NTC (part number 30516) can be used, and other NTC sensors are also compatible. Installation is performed in a standard installation depth of 12.5 mm, and the housing consists of real glass and plastic. The dimensions are 81.5 mm × 81.5 mm (width × height), and the total weight is approximately 70 g. The device is available in the colors RAL 9003 (white) and RAL 9005 (black).

Mounting and Installation

Mounting is done into a suitable device box, taking into account the installation depth of 12.5 mm. Wiring is done via the integrated KNX plug-in terminal, designed for conductors with a diameter of 0.6 to 0.8 mm s. The stripping length is 5 mm. Installation does not require special tools, but suitable screws for securing to the device box are required. The installation manual is included in the delivery and is available in German, English, French, Italian, and Spanish. A handbook and an application are also available for download.

Advantages in Operation

The controller enables precise and user-friendly control of room climate parameters. The touch-sensitive buttons and dimmable LEDs ensure intuitive operation. The integrated logic functions and the ability to form mixed values from internal and external sensors extend the functionality for complex applications. Support for VRF systems and compatibility with KNX networks make the device a flexible solution for modern building automation systems. Operational safety is ensured by the protection rating IP20 and compliance with the standards for overvoltage category III and pollution degree 2.

Scope of Delivery

The scope of delivery includes the room temperature controller, a push button with holder, a KNX plug-in terminal, and the installation manual in multiple languages. A handbook and an application are available for download.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/2035925
qrcode für Elsner 71512 room temperature controller deep black