Elsner 10131, EAN: 4051996101314

Elsner 10131 shading control 230 V perldark grey

Elsner 10131 shading control 230 V perldark grey

Lieske Part No. 2077323
Mfg Part No 10131
EAN-Code 4051996101314
Manufacturer Elsner
Here only 397,14 EUR
472,60 EUR incl. VAT

Further information for Elsner 10131 shading control 230 V perldark grey

Connection for power supply and drive output
Spring-loaded terminals rigid0.5 …1.5 mm²
Spring clamp stripping length10 mm
Spring clamp outer diameter wireØ ≤ 10 mm
Wind measurement range0…35 m/s
Brightness measurement range0 Lux … 150 000 Lux
Drive output
Normally open contactMicro Contact (μ)
With integrated fuseT 5.0 AH
Maximum motor load at drive output500VA (2.17A)
Direction reversal pause1 s
General
HousingPlastic (partially lacquered)
ColoursWhite matt (similar to RAL 9016 traffic white), aluminium matt, pearl dark grey matt
Degree of protectionIP20
Dimensions (W × H × D)103 mm × 98 mm × 28 mm
Total weight (with batteries)≈ 170 g
Ambient temperature0…+45°C
rH (relative humidity), non-condensing5...80 %
Storage temperature control unit10...+50°C
Storage temperature in set10...+50°C
Over voltage categoryIII
Protection classII
Pollution degree2
Colourwhite/translucent
MountingSurface or mast mounting
Weight total≈ 260 g
Storage temperature weather station30...+70°C
Power supply
Battery / accumulator voltage2 × 1.2...1.5 V AA/Mignon
Voltage110 V / 60 Hz, 230 V / 50 Hz
Power consumption≤ 2 W
Sensors
Temperature measurement range0…+50°C
Wireless
Frequency range868.0...868.6 MHz
Transmitting powermax. 10 mW
The Elsner shading control type 10131, from the Solexa 230 V product series, is a wireless control for awnings or blinds with 230 V drive. The device enables automated shading that operates based on brightness and room temperature. The weather station captures outdoor data such as wind speed, precipitation, and brightness to protect shading from rain, wind, or frost. These alarm functions can be individually switched off. For blinds, the opening angle of the slats can additionally be learned (reversing) to allow indirect light into the room. An individual shading position can be set for the automatic mode, so that the shading does not fully extend. The control can also be used as a central unit to control motor control devices IMSG 230.

Applications
The shading control is suitable for use in residential and commercial buildings where automated awning or blind control is desired. It is particularly advantageous for retrofits, as no wiring for power supply or control data needs to be installed within the building. The weather station is mounted outdoors, and the drive is connected directly to the weather station, minimizing cabling effort. The wireless connection between the weather station and the control unit enables decentralized control without cabling inside the building.

Functions and Equipment in Detail
The control unit features a display for showing weather data, alarm messages, and operating mode, as well as integrated buttons. It includes an integrated indoor temperature sensor to measure room temperature. Basic settings, configuration of automatic functions, and manual operation are performed at the control unit. Simultaneous control of multiple drives is possible via a group control relay.

Technology Explained Simply
The control operates in the frequency range 868.0 to 868.6 MHz with a maximum transmission power of 10 mW. The wireless connection between the weather station and the control unit is wireless, requiring no cabling inside the building. The weather station measures outdoor temperature in the range of 0 to +50°C, wind speed up to 35 m/s, and brightness from 0 to 150,000 Lux. The supply voltage is 110 V / 60 Hz or 230 V / 50 Hz, and the power consumption is ≤ 2 W. The drive output features a normally closed contact of type Micro Contact (μ) with an integrated fuse T 5.0 AH. The maximum motor load at the drive output is 500 VA (2.17 A), with a direction reversal pause of 1 second. The terminal connections are spring-cage terminals for conductors with a cross-section of 0.5 to 1.5 mm² and a stripping length of 10 mm. The outer diameter of the conductor must not exceed 10 mm.

Compatibility and Accessories
The shading control is compatible with 230 V drives for awnings or blinds. Control of multiple drives is possible via a group control relay. The wireless remote control Remo 8 (available in white or aluminium-coloured) can be used for manual operation. The button interface RF-B2-UP is also compatible. The control unit is available in the colours white matte (similar to RAL 9016 traffic white), aluminium matte, and pearl dark grey matte. The weather station is white/translucent and can be mounted surface-mounted or on a mast.

Installation and Mounting
The weather station is mounted outdoors, either on a wall (surface-mounted) or on a mast. Mounting is done using a combination holder. The drive is connected directly to the weather station. The control unit is installed indoors, with no cabling required within the building. The wireless connection between the weather station and the control unit enables decentralized control. Installation is simple and does not require special tools.

Operational Advantages
The shading control reduces cabling effort indoors, as no wires for power supply or control data need to be installed. The automatic functions ensure optimal shading that adapts to ambient conditions. The individual setting of the shading position and the reversing function for blinds allow flexible use. The wireless connection enables flexible installation, even for retrofits. The integrated fuse protects the drive from overload. The control is designed for use in an ambient temperature range of 0 to +45°C and relative humidity of 5 to 80 % (non-condensing). The protection rating IP20 protects against finger contact and solid foreign objects, but not against water. The overvoltage category III, protection class II, and pollution degree 2 comply with common safety standards for electrical devices in residential and commercial buildings.

Housing and Colour
The housing is made of plastic, partially lacquered. The control unit is available in the colour pearl dark grey matte. The weather station is white/translucent. The dimensions of the control unit are 103 mm × 98 mm × 28 mm. The total weight of the control unit is approximately 170 g (with batteries), and the total weight of the set is approximately 260 g. The storage temperature for the control unit is between 10 and +50°C, for the set between 10 and +50°C, and for the weather station between 30 and +70°C.

Scope of Delivery
The product includes the control unit (no. 10111, 10121 or 10122) with display, buttons, and integrated indoor temperature sensor, two batteries (1.5 V AA/Mignon), the weather station (no. 10112) with combination holder for wall or mast mounting, and a manual in German, English, French, Italian, Dutch, and Slovenian.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/2077323
qrcode für Elsner 10131 shading control 230 V perldark grey