Further information for Dold 0059742 BN9034/0010 25A AC50/60Hz 400V 15S motor brake device
Technical data
Braking current adjustable up to max.
25 A
Braking time adjustable up to max.
15 s
Width
100 mm
Type
BN 9034
Automatic standstill monitoring
Signalling output
Temperature monitoring
Variant
Auxiliary voltage
Without
Braking current
25 A
Braking time
15 s
Nominal voltage
AC 400 V
Approvals and Markings
UKCA
Variant
Star-delta control
The electronic motor brake device BN9034/0010 from Dold is a device of the MINISTOP series, specifically developed for wear-free braking of three-phase and alternating current asynchronous motors. It ensures safe and reliable stopping of drives that must come to a standstill quickly after switching off for functional or safety reasons. The device is designed for a rated voltage of AC 400 V and supports a frequency of 50/60 Hz. It features an integrated brake with an adjustable braking current up to 25 A and a maximum braking time of 15 seconds. Braking is achieved via DC braking with single-phase rectification, which temporarily supplies the motor’s stator winding with DC voltage to enable rapid deceleration.
Applications
This motor brake device is suitable for industrial applications in machine building and manufacturing technology, particularly in systems such as sawmills, centrifuges, woodworking machines, textile machines, and conveyor systems. In these areas, a short coast-down time is required to increase productivity and minimize safety risks. The device variant with star-delta starting enables a gentle motor start, reducing stress on the motor and drive components.
Functions and Equipment in Detail
The device includes automatic standstill monitoring, which monitors the motor status and switches off the braking current once standstill is reached. In case of standstill-dependent braking, a potential-free signaling contact indicates if the motor has not stopped within the maximum braking time of 15 seconds. This enables early fault detection and increases operational safety. Temperature monitoring via thermistors (optional) protects the motor from overheating. The braking time and braking current are adjustable, allowing the device to be adapted to various motor sizes and requirements.
Technology Explained Simply
DC braking works by supplying DC voltage to the motor’s stator winding as soon as the main motor current is switched off. This generates a braking torque that quickly decelerates the motor. The braking time is controlled by an internal time relay, which switches off the braking current after the set time has elapsed. The integrated brake (braking contactor) is automatically activated as soon as the motor is switched off, after a short safety delay. The device display with LED “ready” indicates that the supply voltage is present, while LED “I” indicates the flowing braking current. Control is achieved via terminals X3–X4, which are connected to the normally open contact of the motor contactor.
Compatibility and Accessories
The device is suitable for all asynchronous motors and can be integrated into existing control systems. It is designed for mounting on a 35 mm standard rail, facilitating installation in enclosures. The variant without auxiliary voltage is intended for standard applications. Optional features include star-delta starting, thermistor motor protection, and a wide voltage range (200–575 V), the latter requiring an auxiliary voltage (AC 230 V or AC 24 V). The devices comply with IEC/EN 60947-4-2 standards and carry the UKCA mark.
Mounting and Installation
Mounting is done by clipping onto a 35 mm DIN rail inside the enclosure. The supply voltage is connected to terminals L1–L2, and the motor to T1–T3. Control is via terminals X3–X4 (start contact) and X5–X6 (interlock for motor contactor). Terminals X1–X2 are optionally used for auxiliary voltage. The maximum allowable cross-sectional area per terminal is 2.5 mm², and the maximum torque for the terminals is 0.8 Nm. The operating temperature range is between 0 °C and +45 °C, and the storage temperature range is between -25 °C and +75 °C. The device has a protection rating of IP 20.
Advantages in Operation
The motor brake device offers higher safety through shorter coast-down times and reduced mechanical stress. It is wear-free and maintenance-free, which reduces operating costs. Easy installation in existing systems and adjustable braking parameters enable flexible use. The integrated standstill monitoring and signaling output increase system reliability. The devices are designed for an 8 % ED duty cycle at maximum braking current, with an I²t value of 1250 A²s for the power semiconductor. Coordination is according to Type 1 as per IEC 60947-4-1, meaning that in the event of a short circuit, the control unit must be replaced.