Dold 0053231, EAN: 4030641532314

Dold 0053231 overcurrent relay IK9272.11/011 AC220-240V 50mA

Dold 0053231 overcurrent relay IK9272.11/011 AC220-240V 50mA

Lieske Part No. 1153687
Mfg Part No 0053231
EAN-Code 4030641532314
Manufacturer Dold
Here only 108,63 EUR
129,27 EUR incl. VAT

Further information for Dold 0053231 overcurrent relay IK9272.11/011 AC220-240V 50mA

Technical data
1- / 3-phase1
Enclosure designDistribution board
Output contacts1 C/O contact
Width17,5 mm
TypeIK 9272
Operate delayYes
Variant
Auxiliary voltageAC 220 - 240 V
Contact equipping1 changeover contact
Measuring range50 mA
Switching delaywithout
Variant1-phasiges Stromrelais. Arbeitsstromprinzip. Nicht speichernd. Ansprechwert fest. Ohne Zeitverzögerung
The Dold overcurrent relay IK9272.11/011 AC220-240V 50mA is a single-phase current relay for monitoring alternating and three-phase power networks. It is used to detect overcurrents and switches the output contact when the set pickup value is exceeded. The device operates on the operating current principle, in which the output relay is activated in the event of a fault. There is no switching delay, but an integrated pickup delay allows for short-term current surges to be considered or ignored. The measurement range covers 50 mA, with the pickup value being infinitely variable within the range. The hysteresis is fixed at approximately 4 %, ensuring stable switching behavior without unwanted oscillations.

Applications
This relay is suitable for use in industrial and installation distributors, particularly in systems requiring continuous current monitoring. It is used in motor and machine monitoring systems, pump control systems, or for monitoring heating and cooling systems. The IK 9272 design is intended for installation and industrial distributors according to DIN 43880, with a depth of 59 mm and connection terminals located at the bottom. The operating temperature ranges from -20 °C to +60 °C, allowing use in indoor environments and protected outdoor areas.

Functions and Equipment in Detail
The device features 1 changeover contact as the output contact, designed for switching operations with a rated voltage of AC 230 V. The thermal current is 5 A, and the relay is designed for continuous operation. The electrical life expectancy is at least 300,000 switching cycles at 1 A and AC 230 V. The mechanical life expectancy exceeds 100 million switching cycles. The contacts are rated for switching capacity according to AC 15: closers up to 3 A / AC 230 V, openers up to 1 A / AC 230 V. Maximum short-circuit withstand is ensured by a maximum fuse rating of 4 A gG / gL.

Technology Explained Simply
The auxiliary voltage is AC 220–240 V, with a nominal consumption of 5.5 VA at AC 230 V. The frequency range is ±5 % around the nominal frequency of 50/60 Hz. Operational reliability is ensured by LED indicators: a green LED indicates the presence of auxiliary voltage, while a yellow LED shows the switching state of the output relay. The connection terminals are designed for conductor cross-sections of 2 x 2.5 mm² solid or 2 x 1.5 mm² stranded wire with ferrules according to DIN 46228. Mounting is done on a DIN rail according to IEC/EN 60715.

Compatibility and Accessories
The relay is specified according to IEC/EN 60255 and meets the requirements for electrical equipment for switching devices. The enclosure protection rating is IP 40, and the terminals are rated IP 20. The device dimensions are 17.5 mm width, 90 mm height, and 59 mm depth. The maximum continuous measured current at an ambient temperature of 50 °C is 2.5 A for the measurement range of 50–500 mA. The maximum overload is 8 A for a maximum of 3 seconds. The response time depends on the set switching delay.

Mounting and Installation
Mounting is done on a DIN rail, with the connection terminals located at the bottom. Conductor attachment is achieved via flat terminals with self-lifting connection washers. The tightening torque is 0.8 Nm. The devices are designed for use in distributors and enclosures, with the IK 9272 design intended for installation distributors.

Operational Advantages
The relay provides precise current monitoring with an adjustable pickup value and pickup delay. The LED indicators allow for quick status checks. The robust construction, high mechanical life expectancy, and short-circuit withstand ensure reliable performance in industrial applications. Compliance with the IEC/EN 60255 standard ensures compatibility with other switching devices and systems.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/1153687
qrcode für Dold 0053231 overcurrent relay IK9272.11/011 AC220-240V 50mA