Dold 0046456, EAN: 4030641464561

Dold 0046456 BD5936.17 AC50/60Hz 230V still-run monitor

Dold 0046456 BD5936.17 AC50/60Hz 230V still-run monitor

Lieske Part No. 1152666
Mfg Part No 0046456
EAN-Code 4030641464561
Manufacturer Dold
Here only 381,30 EUR
453,75 EUR incl. VAT

Further information for Dold 0046456 BD5936.17 AC50/60Hz 230V still-run monitor

Technical data
ClassificationStillstandsüberwachung
Enclosure designSwitch cabinet
Output contacts2 NC contacts, 2 NO contacts
Width45 mm
TypeBD 5936
Variant
Auxiliary voltageAC 230 V 50/60 Hz
Contact equipping2 NO contacts, 2 NC contacts
Approvals and MarkingsCCC
VariantWithout automatic reset for broken wire detection
The Dold BD5936.17 AC50/60HZ 230V is a standstill monitor for monitoring three-phase and single-phase asynchronous motors. The device detects motor standstill without additional sensors by measuring the induced voltage at two terminals of the stator winding. When the induction voltage drops to zero, this is interpreted as motor standstill and the output relay is energized. Simultaneously, the device monitors the measurement circuit between inputs Z1 and Z2 for wire breakage. Upon detection of a wire break, the relay switches to its rest position, which corresponds to the state of a running motor. This state is stored and can only be cleared by briefly switching off the auxiliary voltage.

Standstill monitoring is sensorless, simplifying installation and maintenance. The device is designed for use in enclosures and is suitable, for example, for releasing safety door interlocks on machine tools or for activating holding brakes. The operation is based on measuring the induced voltage in the decelerating motor, with a pickup value of approximately 20 mV and a drop-out value of approximately 40 mV defined.

Functions and equipment in detail include forced-guided output contacts with 2 NO and 2 NC contacts, rated for a nominal voltage of AC 250 V. The contacts are rated for a thermal current load of 5 A and have a switching capacity according to AC 15 of 3 A / AC 230 V for NO contacts and 2 A / AC 230 V for NC contacts. The electrical life is approximately 100,000 switching operations at 2 A and AC 230 V. The auxiliary voltage is AC 230 V at a frequency of 50/60 Hz, with a nominal consumption of approximately 3 VA or 3 W.

Technology explained simply is based on measuring the induced voltage in the motor stator. During the motor's deceleration phase, a voltage is induced, which decreases as the speed drops. When this voltage falls below the pickup value, standstill is detected. Wire break detection is performed via the measurement lines Z1/Z2, which should be connected directly to the motor to minimize interference. For longer runs, twisted cables are recommended. Indication is provided via LEDs: a green LED indicates that the operating voltage is present, a second green LED signals motor standstill, and a red LED lights up in case of wire break.

Compatibility and accessories refer to use with three-phase and single-phase asynchronous motors. The connection terminals allow connection of stranded wires with 2 x 1.5 mm² with ferrule and plastic collar or 2 x 2.5 mm² with ferrule according to DIN 46 228-1/-2/-3/-4. The width is 45 mm, enabling installation in standard enclosures. The device complies with standards IEC/EN 60255-1 and IEC/EN 60255-26 and carries the CCC certification.

Mounting and installation is performed in the enclosure. The measurement lines Z1/Z2 should be connected directly to the motor to avoid interference voltages. For longer runs, the use of twisted cables is recommended. The auxiliary voltage is supplied via terminals A1/A2. The connection terminals are designed for the specified wire cross-sections.

Advantages in operation include sensorless standstill monitoring, which requires no additional mechanical or electronic sensors. Wire break detection with storage ensures a safe response even in case of cable defects. The forced-guided contacts ensure a secure switching function, and the LED indicators enable quick visual diagnosis of the operating status. Compliance with standards IEC/EN 60255-1 and IEC/EN 60255-26 ensures reliability in industrial applications.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/1152666
qrcode für Dold 0046456 BD5936.17 AC50/60Hz 230V still-run monitor