Dold 0039121, EAN: 4030641391218

Dold 0039121 Undervoltage Relay 230V

Industrial Material > Industrial relays and contactors > Switching units / measuring, control relay

Dold 0039121 Undervoltage Relay 230V

Lieske Part No. 773777
Mfg Part No 0039121
EAN-Code 4030641391218
Manufacturer Dold
Here only 302,01 EUR
359,39 EUR incl. VAT

Further information for Dold 0039121 Undervoltage Relay 230V

Technical data
1- / 3-phase3
Auxiliary voltageWithout
Enclosure designSwitch cabinet
Nominal voltage max.3/N AC 690 / 400 V
Output contacts2 C/O contacts
Width45 mm
TypeBA 9043
Operate delayYes
Variant
Contact equipping2 changeover contacts
Nominal voltage3/N 230/400 V
Time delay0,5 - 10 s
Approvals and MarkingsUKCA, CCC
VariantFor 3p4w systems. With adjustable time delay
The under-voltage relay BA9043/002 from Dold is a 3-phase monitoring device for three-phase networks with neutral conductor. It is designed for continuous monitoring of the network voltage and switches off connected loads in case of under-voltage or voltage loss, preventing damage to electrical devices. The device is rated for nominal voltages of 3/N AC 230/400 V and operates within a frequency range of 50 to 400 Hz. Measurement is performed via arithmetic mean value calculation, with each phase measured against the neutral conductor. Device settings are adjusted via rotary potentiometers on the front panel, enabling user-friendly and precise adjustment of pickup and drop-out values.

Applications
This relay is suitable for industrial applications as well as railway applications where reliable voltage monitoring is required. It is mounted in enclosures and designed for continuous operation. The operating temperature range is from -20 °C to +60 °C, and the storage temperature range is from -25 °C to +60 °C. The maximum operating altitude is 2000 m above sea level.

Functions and Equipment in Detail
The device features two changeover contacts as output contacts, suitable for switching operations in AC 15 and DC 13 service. The switching capacity is up to 3 A at AC 230 V and cos φ = 1. The electrical life expectancy is 2 × 10⁵ switching operations at 3 A and AC 230 V. The mechanical life expectancy exceeds 30 × 10⁶ switching operations. The contact configuration allows control of auxiliary functions or safety disconnections. LED indicators signal operational readiness (red LED) and activation of the output relay (green LED).

Technology Explained Simply
The relay operates on the rest current principle, where the output relay remains inactive in the event of a fault and stays in a resting state. Pickup values are continuously adjustable between 0.85 and 1.05 times the nominal voltage. The drop-out value is 0.75 to 0.95 of the pickup value, enabling hysteresis to avoid unwanted switching operations during voltage fluctuations. The time delay is adjustable from 0.5 to 10 seconds and only applies when the voltage is at least 0.6 times the nominal voltage. Below 0.4 times the nominal voltage, the switching-off process occurs immediately.

Compatibility and Accessories
The device is designed for networks with a neutral conductor and complies with standards IEC/EN 60255-1 and VDE 0435. It is insensitive to harmonics and suitable for frequencies from 50 to 400 Hz. The width is 45 mm, allowing mounting on a DIN rail. The terminals are rated for 2 x 2.5 mm² single- or multi-strand conductors, with a stripping length of 10 mm. Mounting is done using plus-minus screws with self-lifting clips.

Installation and Mounting
Mounting is performed on a DIN rail in accordance with IEC/EN 60715. The connection terminals are intended for connection to phases L1, L2, L3 and the neutral conductor N. The output contacts (11, 12, 14 and 21, 22, 24) are connected to the loads or safety functions to be controlled. Adjustment of pickup and drop-out values as well as time delay is done via the rotary potentiometers on the device front.

Operational Advantages
The continuous adjustability of pickup and drop-out values allows precise adaptation to specific network conditions. The LED indicators facilitate fault localization and monitoring of the operational status. Harmonic insensitivity ensures reliable operation even in networks with high harmonics. The time delay prevents unwanted switching-off during short-term voltage dips. The width of 45 mm enables compact mounting in enclosures.

Approvals and Markings
The device carries UKCA and CCC approvals, confirming compliance with applicable safety and quality requirements. The rated impulse withstand voltage is 6 kV at pollution degree 2, and the overvoltage category is III. EMC requirements according to IEC/EN 61000-4-2 to -4-5 are fulfilled.

Switching Capacity and Lifespan
The relay has a switching capacity of 2 A as a make contact and 1 A as a break contact at AC 230 V. The electrical lifespan is 2 × 10⁵ switching operations at 3 A and AC 230 V, and the mechanical lifespan exceeds 30 × 10⁶ switching operations. Maximum short-circuit withstand is ensured by a maximum fuse rating of 4 A gG/gL.

Temperature and Environmental Conditions
The device is designed for operating temperatures from -20 °C to +60 °C. The storage temperature range is from -25 °C to +60 °C. The operating altitude is limited to 2000 m above sea level. The temperature influence on measurement accuracy is less than 0.05 % per Kelvin.

Connection and Mounting
The connection terminals are rated for 2 x 2.5 mm² single- or multi-strand conductors, with a stripping length of 10 mm. Mounting is done using plus-minus screws with self-lifting clips. Installation is on a DIN rail in accordance with IEC/EN 60715. The width is 45 mm.

Additional Features
The device is suitable for networks with frequencies from 50 to 400 Hz. The nominal frequency is 50 to 400 Hz, with a frequency range of ±5 %. The maximum overload capacity is 1.2 times the nominal voltage continuously. The nominal power consumption is AC 4 VA. The adjustment accuracy is ≤ ±10 %.

Approvals and Markings
The device carries UKCA and CCC approvals. The rated impulse withstand voltage is 6 kV at pollution degree 2. The overvoltage category is III. EMC requirements according to IEC/EN 61000-4-2 to -4-5 are fulfilled.

Switching Capacity and Lifespan
The relay has a switching capacity of 2 A as a make contact and 1 A as a break contact at AC 230 V. The electrical lifespan is 2 × 10⁵ switching operations at 3 A and AC 230 V, and the mechanical lifespan exceeds 30 × 10⁶ switching operations. Maximum short-circuit withstand is ensured by a maximum fuse rating of 4 A gG/gL.

Temperature and Environmental Conditions
The device is designed for operating temperatures from -20 °C to +60 °C. The storage temperature range is from -25 °C to +60 °C. The operating altitude is limited to 2000 m above sea level. The temperature influence on measurement accuracy is less than 0.05 % per Kelvin.

Connection and Mounting
The connection terminals are rated for 2 x 2.5 mm² single- or multi-strand conductors, with a stripping length of 10 mm. Mounting is done using plus-minus screws with self-lifting clips. Installation is on a DIN rail in accordance with IEC/EN 60715. The width is 45 mm.

Additional Features
The device is suitable for networks with frequencies from 50 to 400 Hz. The nominal frequency is 50 to 400 Hz, with a frequency range of ±5 %. The maximum overload capacity is 1.2 times the nominal voltage continuously. The nominal power consumption is AC 4 VA. The adjustment accuracy is ≤ ±10 %.

Approvals and Markings
The device carries UKCA and CCC approvals. The rated impulse withstand voltage is 6 kV at pollution degree 2. The overvoltage category is III. EMC requirements according to IEC/EN 61000-4-2 to -4-5 are fulfilled.

Switching Capacity and Lifespan
The relay has a switching capacity of 2 A as a make contact and 1 A as a break contact at AC 230 V. The electrical lifespan is 2 × 10⁵ switching operations at 3 A and AC 230 V, and the mechanical lifespan exceeds 30 × 10⁶ switching operations. Maximum short-circuit withstand is ensured by a maximum fuse rating of 4 A gG/gL.

Temperature and Environmental Conditions
The device is designed for operating temperatures from -20 °C to +60 °C. The storage temperature range is from -25 °C to +60 °C. The operating altitude is limited to 2000 m above sea level. The temperature influence on measurement accuracy is less than 0.05 % per Kelvin.

Connection and Mounting
The connection terminals are rated for 2 x 2.5 mm² single- or multi-strand conductors, with a stripping length of 10 mm. Mounting is done using plus-minus screws with self-lifting clips. Installation is on a DIN rail in accordance with IEC/EN 60715. The width is 45 mm.

Additional Features
The device is suitable for networks with frequencies from 50 to 400 Hz. The nominal frequency is 50 to 400 Hz, with a frequency range of ±5 %. The maximum overload capacity is 1.2 times the nominal voltage continuously. The nominal power consumption is AC 4 VA. The adjustment accuracy is ≤ ±10 %.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/773777
qrcode für Dold 0039121 Undervoltage Relay 230V