Further information for Dold 0038524 CB3056.02 AC/DC24V coupling relay
Technical data
Enclosure design
Switch cabinet
Output contacts max.
1 C/O contact, 2 NO contacts
Thermal current Ith max.
5 A
Width
11,5 mm
Type
CB 3056
Initiator triggering
Suppressor circuit on the coil input
Variant
Contact equipping
2 NO contacts
Nominal voltage
AC/DC 24 V
The Dold coupling relay CB3056.02 AC/DC24V is an industrial relay for contact multiplication and serves as an interface between control and power circuits. It is designed for use in enclosures and features a width of 11.5 mm, enabling compact mounting on standard rail systems. The rated voltage is AC/DC 24 V, allowing operation with both alternating and direct current. The contact configuration includes two normally open contacts, designed for controlling loads up to 3 A at AC 230 V or 1 A at DC 24 V. The maximum contact arrangement is 1 changeover or 2 normally open contacts, with the described variant featuring two normally open contacts.
Applications
This relay is suitable for use in industrial control systems, particularly where potential separation between control and load circuits is required. It is appropriate for switching electrical loads in machine controls, drive technology, automation systems, and other applications requiring safe electrical potential separation according to IEC/EN 61140 and IEC/EN 60947-1, with a rated impulse voltage of 6 kV and pollution degree 2. Operation is specified within a temperature range of -25 °C to +60 °C and at altitudes up to 2000 m above sea level.
Functions and Features in Detail
The device includes an LED indicator that lights up when the relay is energized, visually signaling its operational status. The coil is equipped with a protective circuit at the input, ensuring higher surge voltage resistance. An optional MOV protective circuit is available, further enhancing surge voltage resistance. Contacts are standardly coated with silver-nickel (AgNi); in special variants, a 5 μm gold plating is available, suitable for switching small loads in the range of 2 to 60 V, 1 to 300 mA, and 10 mW to 12 W. At higher switching currents, the gold plating is burned off, rendering the device unsuitable for small load applications thereafter.
Technology Explained Simply
The relay coil is connected to the operating voltage via terminals A1 and A2. When voltage is applied, the armature is attracted, causing the contacts to close. The pickup time is less than 10 ms, and the drop-out time is less than 20 ms. The thermal current rating (Ith) is up to 5 A, indicating the continuous load capacity of the contacts. The mechanical life expectancy exceeds 30 million switching operations, while the electrical life expectancy at AC 15 (3 A, AC 230 V) exceeds 800,000 switching operations. Short-circuit resistance is defined by a maximum fuse rating of 6 A gG/gL according to IEC/EN 60947-5-1.
Compatibility and Accessories
The relay is compliant with IEC/EN 60947-5-1 and suitable for use in systems meeting this standard. It is designed for use in enclosures and can be mounted on standard rail systems. The rated insulation voltage is 300 V, and the overvoltage category is III. The enclosure protection rating is IP 40, and the terminal protection rating is IP 20. EMC requirements are met according to IEC/EN 61000-4-2 to -4-5, including immunity to electrostatic discharge (8 kV), RF radiation (10 V/m), and fast transients (4 kV). The enclosure is made of thermoplastic material with VO behavior according to UL 94.
Mounting and Installation
Mounting is performed in enclosures using a rail system. Terminals A1 and A2 supply the coil, while output contacts (13/14, 23/24) are connected to the loads to be switched. The maximum switching frequency is 20 operations per second. The operating voltage must remain within the specified range: for DC, 80 to 110 % of the rated voltage (with ripple ≥ 10 to 48 %), and for AC, 80 to 110 % of the rated voltage. The rated frequency is 50/60 Hz, with a frequency tolerance of ±5 %.
Operational Advantages
The relay provides safe potential separation, high mechanical and electrical life expectancy, and clear visual operational indication via the LED. The protective circuit at the input enhances reliability against transient voltage spikes. The compact design with a width of 11.5 mm allows dense mounting in enclosures. Compliance with IEC/EN 60947-5-1 ensures suitability for use in standardized industrial installations. The operating temperature range of -25 °C to +60 °C permits use in a wide range of environments, including industrial production facilities and outdoor areas, provided ambient conditions remain within the specified limits.