Further information for Dold 0034163 IK3076.11/004 AC/DC24V coupling relay
Technical data
Enclosure design
Distribution board
Output contacts max.
2 C/O contacts
Thermal current Ith max.
10 A
Width
17,5 mm
Type
IK 3076
Initiator triggering
Suppressor circuit on the coil input
Variant
Contact equipping
1 changeover contact
Nominal voltage
AC/DC 24 V
Variant
For switching low loads
The coupling relay IK3076.11/004 AC/DC24V from Dold serves as an interface between control and power circuits and enables contact multiplication in industrial applications. It is specifically designed for use in installation and industrial distributors according to DIN 43880 and provides safe potential isolation, making it suitable for applications in industry and railway systems. The variant IK3076.11/004 is designed for operation with a nominal voltage of AC/DC 24 V and features a contact configuration with one changeover contact. The width is 17.5 mm, enabling compact mounting in standard distributors. The device is designed for continuous operation and can be used at operating temperatures from -25 °C to +60 °C.
Applications
This coupling relay is intended for use in control systems where galvanic isolation between control and power circuits is required. It is particularly suitable for applications where small loads such as signal lamps, relays, or small motors need to be switched. The design for switching small loads makes it especially suitable for systems with low current requirements. Use in railway applications is permitted due to the high EMC requirements and safety standards IEC/EN 60947-5-1 and IEC/EN 61810-1.
Functions and Equipment in Detail
The device features an LED indicator that lights green when the relay is energized, enabling visual monitoring of the operating status. The contact configuration includes one changeover contact, designed for switching operations with a thermal current Ith of up to 10 A. The pickup and drop-out time is less than 10 ms and less than 20 ms respectively, ensuring a fast response to control signals. The switching capacity according to AC 15 is 3 A at AC 230 V for the normally open contact and 1 A for the normally closed contact. For direct current (DC 13), the switching capacity is 1 A at DC 24 V for both normally open and normally closed contacts.
Technology Explained Simply
The relay coil is protected by an input protection circuit that absorbs voltage surges and thus extends the device’s service life. The electrical life is 100,000 switching operations at 3 A and AC 230 V, while the mechanical life exceeds 30 million switching operations. The short-circuit withstand capability is specified with a maximum fuse rating of 10 A gG/gL for the IK3076.11 variant. The permissible switching frequency is 6000 switching operations per hour. The housing design is intended for installation distributors, with connection terminals located at the bottom and a depth of 59 mm. Mounting is either via DIN rail (IEC/EN 60715) or via screw mounting with M4 screws.
Compatibility and Accessories
The relay, with a width of 17.5 mm, is compatible with standard DIN rail systems. It can be used in combination with other coupling relays from the IK3076 series, with the variant IK3076.12 featuring two changeover contacts available as an alternative. The connection terminals are designed for conductor cross-sections of 2 x 2.5 mm² (solid) or 2 x 1.5 mm² (stranded wire with ferrule DIN 46228-1/-2/-3/-4). The stripping length is 10 mm, and the tightening torque for the terminals is 0.8 Nm.
Mounting and Installation
Mounting is either via snap-in on a DIN rail according to IEC/EN 60715 or via screw mounting with M4 screws on a 90 mm grid. The terminals are located at the bottom, facilitating integration into installation distributors. Terminal marking follows EN 50005, with A1 and A2 representing coil inputs, and 11, 12, 14 representing contacts of the first changeover contact.
Advantages in Operation
The coupling relay offers high operational reliability due to galvanic isolation and the integrated input protection circuit. The LED indicator enables simple status monitoring. The high mechanical life and short response time make it suitable for applications with high switching frequencies. Compliance with standards IEC/EN 60947-5-1, IEC/EN 61810-1, and IEC/EN 61140 ensures adherence to safety and functional requirements in industrial environments. The protection rating IP 40 for the housing and IP 20 for the terminals protects against contact and foreign objects, with the device intended for use in enclosed enclosures.