DEHN 952308, EAN: 4013364120716

DEHN 952308 surge arrester 3-pole TN-C

Energy > Surge Protection

DEHN 952308 surge arrester 3-pole TN-C

Lieske Part No. 926688
Mfg Part No 952308
EAN-Code 4013364120716
Manufacturer DEHN
Here only 370,97 EUR
441,45 EUR incl. VAT

Further information for DEHN 952308 surge arrester 3-pole TN-C

General
NormEN 61643-11
Degree of protectionmultipolar
SystemTN-C
Monitoring technologyThermo-Dynamik-Control
Applicationlightning protection zones concept
Interface0B - 1 and higher
Standards
CertificationUL
UL StandardUL 1449 5th edition
UL File NumberE319777
Technical data
Energy coordination with terminal equipment (≤ 10 m)type 2 + type 3
Nominal voltage (a.c.) (UN)400 / 690 V (50 / 60 Hz)
Max. continuous operating voltage (AC) (UC)440 V (50 / 60 Hz)
Nominal discharge current (8/20 µs) (In)20 kA
Max. discharge current (8/20 µs) (Imax)40 kA
Voltage protection level (UP)≤ 2 kV
Voltage protection level at 5 kA (UP)≤ 1.7 kV
Response time (tA)≤ 25 ns
Max. mains-side overcurrent protection125 A gG
Short-circuit withstand capability for max. mains-side overcurrent protection (ISCCR)50 kArms
Temporary overvoltage (UT) – characteristic580 V / 5 sec. – Festigkeit, 765 V / 120 min. – sicherer Ausfall
Operating temperature range (TU)-40 °C ... +80 °C
Operating state / fault indicationgreen / red
Number of ports1
Cross-sectional area (min.)1.5 mm2 solid / flexible
Cross-sectional area (max.)35 mm2 stranded / 25 mm2 flexible
For mounting on35 mm DIN rails acc. to EN 60715
Enclosure materialthermoplastic, red, UL 94 V-0
Place of installationindoor installation
Degree of protectionIP 20 (integrated)
Capacity3 Standard DIN module, DIN 43880
ApprovalsDEKRA, UL
Type of remote signalling contactchangeover contact
Switching capacity (a.c.)250 V / 0.5 A
Switching capacity (d.c.)250 V / 0.1 A; 125 V / 0.2 A; 75 V / 0.5 A
Cross-sectional area for remote signalling terminalsmax. 1.5 mm2 solid / flexible
Test values according to UL 1449
Rated Voltage (AC, 50/60 Hz)400 V
MCOV (AC, 50/60 Hz) [L-N]/[L-G]/[N-G]440 V
Voltage protection rating (VPR)≤ 1700 V
Nominal discharge current (8/20µs) ( In)20 kA
Maximum ambient temperature85 °C
UL 1449 edition5th edition
Type (SPD classification)Type 4 component assembly
The DEHNguard M, Type 2, model DG M TNC 440 FM, is a multipole surge arrester of the brand DEHN, developed for the protection function of low-voltage consumer installations against transient overvoltages. It serves as a protective measure in the lightning protection zone concept at interfaces 0B – 1 and higher, covering the transitions between protection zones to safeguard electrical devices and installations from damage caused by lightning or induction overvoltages. The device consists of a base unit into which protection modules are inserted, enabling a modular and adaptable configuration.

Applications

The surge arrester is intended for use in electrical installations in the low-voltage range, particularly in buildings supplied with an electrical system using a TN-C system. It is installed at the transitions between lightning protection zone 0B and zone 1, as well as higher zones, to protect power supply systems from transient voltage spikes caused by direct or indirect lightning strikes. The application typically occurs near distributors or at the entry interface of the electrical installation.

Functions and Equipment in Detail

The arrester provides high device safety through integrated arrester monitoring with Thermo-Dynamik-Control. This technology continuously monitors the condition of the arrester and responds to thermal changes that may indicate a malfunction or wear. This enables early detection of defects, increasing the reliability of the protective function. The design as a multipole arrester allows the protection of multiple conductors within a single device, ensuring a compact and efficient installation.

Technology Explained Simply

The DEHNguard M operates according to standard EN 61643-11, which defines surge protection devices of types 2 and 3. As a Type 2 device, it is designed for use at the interface between zone 0B and zone 1, where it can divert overvoltages with a nominal impulse voltage of 1.2/50 µs and an impulse voltage of 4 kV (for 10/350 µs). The designation TNC indicates use in a TN-C system, where the neutral conductor and protective conductor are combined. The modular design allows flexible adaptation to different installation configurations, with individual protection modules inserted into the base unit.

Compatibility and Accessories

The arrester is specifically designed for use in TN-C systems, meaning it is intended for installations with combined neutral and protective conductors. It is part of the DEHNguard M series and can be combined with other modules from this series to achieve different protection configurations. The use of additional protection modules requires no special tools or additional components, as the modules are directly inserted into the base unit.

Mounting and Installation

Installation typically takes place in a distribution box or at the entry interface of the electrical installation. Mounting is done by installing the base unit into a suitable switch cabinet, with protection modules inserted into the appropriate sockets as needed. Electrical connections are made at the designated terminals, ensuring correct assignment of conductors (e.g., L, N, PE). Mounting does not require special tools, but compliance with VDE and EN standards for electrical installation is mandatory.

Advantages in Operation

The DEHNguard M provides reliable protection through integrated monitoring technology, enabling early detection of defects. The modular design simplifies adaptation to different installation configurations and reduces installation time. Compliance with standard EN 61643-11 ensures conformity with applicable safety standards. Use within the lightning protection zone concept ensures a structured and effective protection strategy covering the entire electrical installation.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/926688
qrcode für DEHN 952308 surge arrester 3-pole TN-C