DEHN 952096, EAN: 4013364109926

DEHN 952096 DG S 600 FM surge arrester 1-pole 600 V AC

Energy > Surge Protection

DEHN 952096 DG S 600 FM surge arrester 1-pole 600 V AC

Lieske Part No. 791448
Mfg Part No 952096
EAN-Code 4013364109926
Manufacturer DEHN
Here only 133,38 EUR
158,72 EUR incl. VAT

Further information for DEHN 952096 DG S 600 FM surge arrester 1-pole 600 V AC

General
Degree of protectionType 2
NormEN 61643-11
Monitoring technologyThermo-Dynamik-Control
Application arealow-voltage consumer installations
Use in lightning protection zone conceptinterfaces 0B – 1 and higher
Type of deviceSingle-pole surge arrester
ManufacturerDEHN
Constructionbase unit with inserted protection module
Technical data
Max. continuous operating voltage (AC) (UC)600 V (50 / 60 Hz)
Nominal discharge current (8/20 µs) (In)20 kA
Max. discharge current (8/20 µs) (Imax)40 kA
Voltage protection level (UP)≤ 2.5 kV
Max. mains-side overcurrent protection100 A gG
ApprovalsDEKRA, VDE, UL, CSA
Type of remote signalling contactchangeover contact
Test values according to UL 1449
Rated Voltage (AC, 50/60 Hz)600 V
MCOV (AC, 50/60 Hz)600 V
MLV (AC, 50/60 Hz)2820 V
Nominal discharge current (8/20µs) ( In)20 kA
Maximum ambient temperature+85 °C
AWG (conductors)2-14 Cu solid/stranded
AWG (remote indicator)14-22 Cu
UL 1449 edition5th edition
Type (SPD classification)Type 4 component assembly
The DEHNguard S 600 FM is a single-pole surge arrester of Type 2 category, designed for the protection of low-voltage consumer installations against transient overvoltages. The manufacturer is DEHN, and the device carries the manufacturer's number 952096. It is used within the lightning protection zone concept, particularly at interfaces 0B – 1 and higher, where the risk of overvoltages due to direct or indirect lightning effects exists. The device consists of a base unit and an inserted protection module, enabling a modular and flexible installation.

Applications

The arrester is intended for use in electrical installations within the low-voltage range, particularly in buildings where sensitive electronic devices are connected. It protects connected consumers against overvoltages caused by lightning effects, network disturbances, or other electrical interference sources. The application typically occurs in the transition zone between outdoor and indoor installations, where voltage spikes are most intense.

Functions and Equipment in Detail

The DEHNguard S 600 FM provides high device safety through integrated arrester monitoring with Thermo-Dynamic-Control. This technology continuously monitors the condition of the arrester and responds to thermal overloads, which may indicate damage or malfunction. This enables early detection of defects, increasing the reliability of the protection system. The device is designed for use in electrical installations dimensioned according to the lightning protection zone concept.

Technology Explained Simply

The arrester operates according to the principle of a Type 2 surge arrester in accordance with EN 61643-11. When overvoltages exceed a certain threshold, it diverts the energy through a discharge resistor or varistor to reduce the voltage to a level tolerable for connected devices. The Thermo-Dynamic-Control technology monitors the temperature of the protection module and can trigger an alarm or shutdown process if signs of overload are detected. This prevents a defective arrester from continuing to operate in the network and thus posing a hazard.

Compatibility and Accessories

The arrester is designed for use in low-voltage installations and can be used in combination with other DEHN protection devices to implement a comprehensive protection concept. It is used at interfaces 0B – 1 and higher within the lightning protection zone concept, with exact positioning depending on the specific installation configuration.

Mounting and Installation

Installation takes place in a suitable enclosure or distribution box. The device is connected to the respective line, with electrical connections to be made in accordance with applicable standards and regulations. Mounting is achieved by inserting the protection module into the base unit, enabling quick and secure installation.

Advantages in Operation

The DEHNguard S 600 FM provides reliable protection for sensitive electronic devices. The integrated monitoring technology increases safety by enabling early detection of defects. The modular design allows for easy maintenance and replacement of the protection module without having to replace the entire device. Compliance with standard EN 61643-11 ensures standardized performance and compatibility with other protection systems.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/791448
qrcode für DEHN 952096 DG S 600 FM surge arrester 1-pole 600 V AC