BlackBox LMC5023C-R3

BlackBox LMC5023C-R3 Media Converter 100BASE-TX to 100BASE-FX

Networks > Media-Converters

BlackBox LMC5023C-R3 Media Converter 100BASE-TX to 100BASE-FX

Lieske Part No. 475091
Mfg Part No LMC5023C-R3
EAN-Code
Manufacturer BlackBox
Here only 375,36 EUR
446,68 EUR incl. VAT

Further information for BlackBox LMC5023C-R3 Media Converter 100BASE-TX to 100BASE-FX

General
Copper interface100BASE-TX
Fibre optic interface100BASE-FX
Fibre typeMulti mode
Wavelength1300 nm
Fibre optic connectorSC
Transmission range2 km
Layer1
System compatibilityHigh-Density Media Converter System II
The product is a Layer 1 module for the High-Density Media Converter System II from BlackBox. It is designed for converting Ethernet signals between copper and fiber optic cables, specifically from 100BASE-TX over twisted-pair cables to 100BASE-FX over multimode fiber optic cables. The module is intended for use in networks requiring extension of transmission distances over longer ranges without losing the network speed of 100 Mbit/s. The conversion takes place at Layer 1, i.e., at the physical level, meaning no protocol processing or packet analysis occurs — the function is limited to signal regeneration and conversion.

Applications
This module is suitable for networks requiring a connection between copper and fiber optic segments, for example in building cabling, when connecting outdoor stations, or in industrial environments where cable installation covers long distances. The multimode fiber optic cable with a 1300 nm wavelength enables transmission over up to 2 km, which is sufficient for many enterprise networks. The use of SC connectors is standard in many network infrastructures and ensures a secure mechanical connection.

Functions and Features in Detail
The module converts signals from 100BASE-TX (copper, RJ45) to 100BASE-FX (fiber optic, SC). The 100BASE-TX interface supports transmission over twisted-pair cables according to Ethernet standardization, with a typical maximum range of 100 meters on copper cables. The fiber optic side extends this range up to 2 km, using multimode fiber with a 1300 nm wavelength. The conversion occurs without processing on higher protocol layers, minimizing latency and increasing installation simplicity.

Technology Explained Simply
The technology is based on converting electrical signals (copper) into optical signals (fiber optic) and vice versa. The module receives an electrical signal via the RJ45 interface, converts it into a light signal, which is transmitted over the multimode fiber optic cable. On the receiving side, the light signal is converted back into an electrical signal. The 1300 nm wavelength is common for multimode fibers and offers a good balance between bandwidth and attenuation. The SC connector is a standard fiber optic connector that enables a secure and easy connection.

Compatibility and Accessories
The module is specifically developed for the High-Density Media Converter System II and is used within this system. It is designed as a Layer 1 module, meaning it does not process any network layer higher than the physical layer. Compatibility is limited to use with other modules of the same system. No specific additional hardware or software is required to operate the module. Connections are made via standardized interfaces, enabling integration into existing networks without additional configuration.

Installation and Mounting
The module is installed into the High-Density Media Converter System II, which features a modular design. Installation is done by inserting the module into the appropriate slot of the system. No additional tools or configuration steps are required. Cabling is done via the RJ45 interface for the copper cable and via the SC connector for the fiber optic cable. The connection becomes active immediately after insertion, as soon as the physical connections are established.

Operational Advantages
Using this module enables extension of network reach without speed loss. Conversion at Layer 1 minimizes latency and maintains stable network performance. The multimode fiber optic cable with 1300 nm wavelength provides sufficient range for many enterprise applications. The SC connector is robust and widely used, simplifying maintenance and replacement. The module is designed for use within a system, enabling a scalable and flexible network architecture.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/475091
qrcode für BlackBox LMC5023C-R3 Media Converter 100BASE-TX to 100BASE-FX