Further information for ABB 2CSF204101R2400 RCD 4-pole 100mA
General
Number of poles
4
Rated current
40
Rated impulse withstand voltage Uimp
4
Mounting method
DIN rail
Leakage current type
A
Frequency
50/60 Hz
Degree of protection (IP)
IP20
Width in number of modular spacings
4
Built-in depth
69
Ambient temperature during operating
55
Pollution degree
2
Connectable conductor cross section multi-wired
25
Connectable conductor cross section solid-core
25
Depth of device
69
Height of device
85
RAL-number (akin)
7035
Width of device
70
Selective protection
Short-time delayed tripping
Additional equipment possible
With interlocking device
Explosion-proof
The residual current circuit breaker F204 A-40/0.1 from ABB is a 4-pole circuit breaker with a rated current of 40 A and a rated residual current of 0.1 A (100 mA). It is designed for use in electrical installations requiring personal and property protection as well as fire protection in accordance with DIN VDE 0100-410 and DIN VDE 0100-530. The F200 series provides protection against sinusoidal alternating currents and pulsating currents with a smooth direct residual current component up to 6 mA, which is particularly relevant for modern electronic devices. The switch complies with product standards IEC/EN 61008-1, 61008-2-1, 61543 (corresponding to VDE 0664-10, -11, -30) and is also UL 1053 certified for F200 A circuit breakers up to 100 A. It is therefore suitable for use in domestic, commercial, and industrial applications.
Residual current circuit breaker provides protection against indirect contact (fault protection), additional protection (at IΔn = 30 mA), and fire protection (at IΔn = 300 mA). The switch is of type A, meaning it can detect both alternating and direct residual currents, which is important for installations with electronic loads. It is non-selective and not time-delayed, making it suitable for use in main distribution or installations with direct protection. Mounting is done on a DIN rail, enabling standardized installation in distribution boxes.
Technology explained simply: The switch responds to a residual current of 100 mA and disconnects the power supply within the specified time to prevent injuries or fires. The rated impulse voltage withstand is 4 kV, making it suitable for installations with normal overvoltage category. The operating ambient temperature may reach up to 55 °C, and the switch is designed for pollution degree 2, which is typical for indoor environments with normal contamination. The protection rating IP20 means it is protected against contact with fingers and against solid foreign objects up to 12.5 mm, but not against water or dust – therefore, it is intended exclusively for indoor use.
Compatibility and accessories: The device can be equipped with additional components, with suitable accessories including the auxiliary switch LS S2C-H6-11R, the Si-automat S200 B+ LS S2C-H6-20R, or the S2C-S/H6R auxiliary switch 1 changeover for LS and FI. These components allow for functional expansion, such as remote control or status indication, and are suitable for integration into more complex switching installations. The connection cross-sections are designed for single-core and multi-core conductors up to 25 mm², enabling flexible wiring in various installations.
Mounting and installation: The switch is mounted on a DIN rail and requires a width of 4 module units (equivalent to 70 mm). The installation depth is 69 mm, allowing it to be easily integrated into standard distribution boxes. The device dimensions are 70 mm (width) × 85 mm (height) × 69 mm (depth). The color corresponds approximately to RAL number 7035, which is a standard gray tone commonly used in electrical distribution boards.
Operational advantages: The combination of 4-pole design, residual current protection type A, and compliance with international standards makes the F204 A-40/0.1 a reliable protective device for a wide range of applications. The integrated locking device enables secure protection of the switch, for example during maintenance work. Compliance with standards IEC/EN 61008-1 and UL 1053 ensures worldwide usability in various markets.