ABB 2CSF204101R1400, EAN: 8012542783503

ABB 2CSF204101R1400 RCD 4-pole 40A

Installation > Modular devices / equipment installation > RCD

ABB 2CSF204101R1400 RCD 4-pole 40A

Lieske Part No. 290324
Mfg Part No 2CSF204101R1400
EAN-Code 8012542783503
Manufacturer ABB
Here only 136,80 EUR
162,79 EUR incl. VAT

Further information for ABB 2CSF204101R1400 RCD 4-pole 40A

General
Number of poles4
Rated current40
Rated impulse withstand voltage Uimp4
Mounting methodDIN rail
Leakage current typeA
Frequency50/60 Hz
Degree of protection (IP)IP20
Width in number of modular spacings4
Built-in depth69
Ambient temperature during operating55
Pollution degree2
Connectable conductor cross section multi-wired25
Connectable conductor cross section solid-core25
Depth of device69
Height of device85
Power loss9.6
RAL-number (akin)7035
Width of device70
Selective protectionno
Short-time delayed trippingno
Additional equipment possibleyes
With interlocking deviceyes
Explosion-proofno
The residual current circuit breaker F204 A-40/0.03 from ABB is a 4-pole circuit breaker for installation in electrical installations. It provides protection for persons, installations and buildings against electrical hazards, particularly in cases of indirect contact, as well as fire prevention through detection and disconnection in the event of fault currents. The breaker is designed for use in household, commercial and industrial applications and complies with relevant standards, including IEC/EN 61008-1, 61008-2-1 and 61543 (corresponding to VDE 0664-10, -11, -30), as well as UL 1053 for the F200 series up to 100 A. It is designed for frequencies of 50/60 Hz and provides protection against sinusoidal alternating currents as well as pulsating currents with a smooth direct fault current component up to 6 mA to earth.

Residual current circuit breaker models of the F204 series are designed for use in electrical installations where high safety is required. The breaker is rated for a nominal current of 40 A and trips at a fault current of 30 mA, which corresponds to additional protection according to DIN VDE 0100-410. For fire protection applications, disconnection is provided at 300 mA, meeting the requirements for electrical fire protection. The protection functions include fault protection (protection against indirect contact), additional protection (IΔn = 30 mA) and fire protection (IΔn = 300 mA), with disconnection at 30 mA primarily relevant for personal protection.

Residual current type A means that the breaker can also detect and disconnect pulsating direct fault currents, which is particularly important for installations with electronic devices, such as computers, LED lighting or frequency converters. The rated impulse voltage withstand is 4 kV, ensuring reliability during transient voltage surges. The protection class IP20 ensures protection against contact with fingers and against solid foreign objects, but not against water or dust – therefore, use is intended for indoor environments without special environmental stresses.

DIN rail mounting enables simple and standardized installation in enclosures or distribution boxes. The mounting depth is 69 mm, the device width 70 mm and the height 85 mm, with the width corresponding to 4 module units. The maximum ambient temperature during operation is 55 °C, and pollution degree 2 is intended for environments with low pollution. The breaker can be connected with single-core and multi-core conductors up to 25 mm², enabling flexible wiring. The power loss is 9.6 W, describing the thermal load during operation.

Additional features such as auxiliary switches or interlocking devices are possible, allowing the breaker to be integrated into more complex installations. The interlocking device enables mechanical interlocking to prevent accidental switching on. Suitable accessories include auxiliary switches such as the LS S2C-H6-11R or S2C-S/H6R, as well as busbars such as PS3/9-FI or PS4/12, suitable for connecting multiple devices in a distribution board. The phase busbar PS3/12FI is designed for 1x F204+S200 L1 L2 L3 N and allows flexible arrangement of conductors.

Compatibility with other devices from the F200 and S200 series is provided, particularly when using busbars and auxiliary switches. The devices are designed for use in electrical distributions where safe and reliable disconnection in the event of fault currents is required. The color corresponds approximately to RAL number 7035, describing a gray surface that blends into standardized enclosures.

Operation and maintenance require no special measures. The mechanical interlock and the possibility of integrating auxiliary switches facilitate monitoring and control in complex installations. The devices are designed for indoor use, with protection class IP20 requiring application in dry, low-pollution environments. Mounting on DIN rail enables standardized and quick installation. Connection cross-sections up to 25 mm² for single-core and multi-core conductors ensure flexible wiring in various applications.

Operational advantages include reliable disconnection in the event of fault currents, compatibility with accessories and easy mounting. Compliance with standards IEC/EN 61008-1 and -2-1 as well as VDE 0664-10, -11, -30 ensures conformity with European and international safety requirements. Use in household, commercial and industrial applications demonstrates the versatility of the device. The integrated interlocking device and the possibility of extending with auxiliary switches enhance functionality in complex control systems.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/290324
qrcode für ABB 2CSF204101R1400 RCD 4-pole 40A