Further information for Telegärtner L00006A0048 patch cable Cat7 50 m blue
General
Cable type
S/FTP
Category
Cat.6A
Bandwidth
500 MHz
Connector type
RJ45
Plug sleeve
moulded, 90°/180°/270°, with latch protection
Connection sequence
EIA/TIA 568B
Colour
Blue
Conductor material
Cu
Material outer sheath
LSZH
Surge insulation test
6 kV
PoE support
IEEE 802.3bt
Cable construction
4x2xAWG27/7
Class
EA
Bush with RFID transponder
Mounting clip slots
Cable length on ferrule
The Telegärtner patch cable type 100009129 is an S/FTP cable of category 6A with a length of 50 metres and a bandwidth of 500 MHz. It is designed for use in networks supporting data transfer rates up to 10 Gbit/s and complies with the requirements of class EA according to ISO/IEC. The cable is equipped with RJ45 connectors of type MP8, featuring a moulded boot available in angles of 90°, 180°, or 270°. This boot provides a latch protection and includes grooves for mounting clips, facilitating installation in patch panels or rack systems. The wiring sequence follows EIA/TIA 568B, ensuring standardised cabling. The cable colour is blue, with additional colour variants such as grey, green, red, yellow, black, white, and purple available. The cable length is directly indicated on the connector boot, simplifying identification and management within the network.
Patch cable of this type is designed for use in structured cabling systems, particularly in office environments, server rooms, or for connecting network devices such as switches, routers, or end devices. The use of S/FTP technology (Screened/Foiled Twisted Pair) provides a high level of protection against electromagnetic interference (EMI) and enables reliable data transmission over longer distances. The cable is suitable for use with Power over Ethernet (PoE) according to IEEE 802.3bt, enabling power supply to end devices via the network cable. The conductors are made of copper (Cu) and are surrounded by an LSZH material (Low Smoke Zero Halogen) jacket, ensuring minimal smoke development and no release of halogens in case of fire. The surge voltage insulation test is performed at 6 kV, confirming the electrical safety of the cable.
Technology explained simply: The S/FTP structure means that the entire cable is shielded with a braided jacket, and additionally, each pair is individually protected by a foil shield. This reduces crosstalk and enhances signal integrity, especially at high frequencies. The cable construction with AWG27/7 (equivalent to a diameter of approximately 0.5 mm per single wire) ensures sufficient conductivity and mechanical stability. The use of LSZH material in the jacket is particularly advantageous in enclosed spaces such as server rooms or office buildings, as it does not release toxic gases when heated. The boot with RFID transponder enables AIM functionality (Asset Information Management), allowing the cable to be identified within inventory and management systems.
Compatibility and accessories: The cable is compatible with all devices supporting Cat.6A and ISO/IEC EA standards. It can be used in conjunction with patch panels, network switches, and other network devices. The available accessories include additional patch cables of category 6A in various lengths (e.g. 0.5 m to 50 m) and with similar characteristics such as S-STP (S/FTP), AWG26, LSZH, and GHMT certification. These items are also suitable for 10 Gbit/s Ethernet and PoE and can be used to extend or supplement existing networks.
Installation and mounting: Installation is performed by simply inserting the RJ45 connectors into the corresponding sockets. The moulded boot in angles of 90°, 180°, or 270° allows for flexible positioning, especially in tight racks or when connecting to devices requiring different angles. The grooves in the boot allow for fixation with a mounting clip, securing the cable neatly and preventing it from being pulled out of the socket during operation or movement. The cables are designed for indoor use, with the LSZH insulation meeting safety requirements in confined spaces.
Operational advantages: The high bandwidth of 500 MHz and support for 10 Gbit/s Ethernet enable fast and stable data transmission, even under heavy loads. PoE support according to IEEE 802.3bt reduces the need for additional power supplies for end devices. The integrated RFID functionality simplifies management and documentation within the network. The robust construction with copper conductors and LSZH jacket ensures long service life and high reliability. The standardised wiring according to EIA/TIA 568B ensures compatibility with existing systems and simplifies maintenance.