| General |
| Degree of protection | C |
| Nominal current | 4 A |
| Rated switching capacity | 10 kA |
| Operating voltage DC | 440 V |
| Operating voltage AC | 400 V |
| Number of poles | 2 way |
| Height | 70 mm |
| Terminal technology | double chamber terminal |
| Mounting method | tool-free with double slide |
| Accessory compatibility | uniform for 5SY series |
The circuit breaker
5SY5204-7 from Siemens belongs to the SENTRON series and is designed for safe short-circuit and overload protection in electrical installations. It is a
2-pole switch with a rated current of
4 A. The protection type
C indicates the tripping characteristic, suitable for applications with moderate inrush currents. The switch is designed for operating voltages of
440 V DC and
400 V AC and features a rated switching capacity of
10 kA, qualifying it for use in residential buildings, utility buildings, and special industrial applications. The design allows for tool-free mounting and dismounting via a double slider, simplifying installation and maintenance. The terminals are designed as double chamber terminals, enabling any combination of conductors and busbars. Power input is via a rear-mounted busbar, simplifying wiring. The 5SY switch series is available in various pole configurations, including 1-, 2-, 3-, 4- as well as 1+N- and 3+N-pole versions. Accessories are uniformly designed for all 5SY switches and can be universally used.
Applications
The switch is intended for use in electrical distributions within the field of building electrotechnics and in special industrial installations. It protects lines and consumers against overload and short-circuit. The protection type C is particularly suitable for installations with motors, heaters, or other devices that exhibit higher inrush currents during startup. The high rated switching capacity of 10 kA also makes it suitable for installations with increased short-circuit stresses.
Functions and Equipment in Detail
The switch features a double chamber terminal, enabling flexible connections between conductors and busbars. The rear busbar simplifies wiring for power input. Tool-free mounting via a double slider reduces installation effort and allows for quick and secure fixation in the enclosure. The 5SY switch series is modular, allowing various accessories such as auxiliary switches, isolation devices, or pin busbars to be easily installed. The switches are designed with a standard height of 70 mm, enabling standardization in distributions.
Technology Explained Simply
The protection type C means that the switch trips at a current of approximately 5 to 10 times the rated current (here 4 A). This is typical for installations where short-term current peaks occur, for example with motors or electronic devices. The rated switching capacity of 10 kA describes the maximum energy the switch can safely interrupt during a short-circuit. The operating voltages of 440 V DC and 400 V AC cover both DC and AC applications, with the DC voltage being relevant for industrial or special installations. The design is intended for installation in enclosures, with the mounting height of 70 mm enabling standardization within the SENTRON series.
Compatibility and Accessories
Accessories for the 5SY series are uniformly designed and can be universally used. Available components include auxiliary switches such as the 5ST3010, isolation devices such as the 5ST3803, pin busbars in various configurations (e.g. 5ST3608, 5ST3610, 5ST3736), and adapters for remote actuators such as the 5ST38201. Remote actuators such as the 5ST3073-0MC enable remote control of the switch. Combination with RCD modules such as the 5SM2322-6KK01 or 5SM2622-0 is possible to integrate additional fault current protection. Busbars are available in various cross-sections (e.g. 10 mm², 16 mm²) and configurations (e.g. 2-pole, 6x2-pole) to meet different wiring requirements.
Mounting and Installation
Mounting is tool-free via a double slider, which locks the switch into the enclosure. The terminals are designed to connect both conductors and busbars. The rear busbar simplifies wiring for power input. The standard height of 70 mm enables easy integration into existing distributions. The switches can be mounted in rows, with the modular design allowing flexible arrangement. Installation takes place in standard enclosures or distributions designed for the respective voltage and power.
Advantages in Operation
The switch offers high reliability due to its robust construction and high rated switching capacity. Tool-free mounting reduces installation time and minimizes the risk of mounting errors. The modular design enables flexible expansion of the installation with accessories. Uniform accessory compatibility within the 5SY series simplifies planning and maintenance. The protection type C provides balanced protection, effective under normal operating conditions as well as during short-term current peaks. Use in residential and utility buildings as well as in special industrial applications demonstrates the versatility of the device.