| Complementary |
| Maximum mechanical speed | 3800 rpm |
| [Us] rated supply voltage | 115...480 V |
| Network number of phases | Three phase |
| Continuous stall current | 21 A |
| Continuous stall torque | 36.9 N.m at 115...480 V three phase |
| Continuous power | 5500 W |
| Peak stall torque | 110 N.m at 115...480 V three phase |
| Nominal output power | 2510 W at 115 V single phase; 4240 W at 230 V single phase; 5500 W at 400 V three phase; 5200 W at 480 V three phase |
| Nominal torque | 31.9 N.m at 115 V single phase; 27 N.m at 230 V single phase; 17.5 N.m at 400 V three phase; 13.8 N.m at 480 V three phase |
| Nominal speed | 750 rpm at 115 V single phase; 1500 rpm at 230 V single phase; 3000 rpm at 400 V three phase; 3600 rpm at 480 V three phase |
| Maximum current Irms | 87.2 A |
| Shaft end | Parallel key |
| Shaft diameter | 38 mm |
| Shaft length | 80 mm |
| Key width | 10 mm |
| IP degree of protection | IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5; IP65 motor: conforming to IEC 60034-5; IP65 shaft bushing: conforming to IEC 60034-5 |
| Encoder type | Absolute multiturn SinCos Hiperface |
| Speed feedback resolution | 128 periods |
| Holding brake | Without |
| Mounting support | International standard flange |
| Motor flange size | 205 mm |
| Electrical connection | Straight connector |
| Torque constant | 1.75 N.m/A at 120 °C |
| Back emf constant | 104 V/krpm at 20 °C |
| Number of motor poles | 5.0 |
| Rotor inertia | 71.4 kg.cm² |
| Stator resistance | 0.3 Ohm |
| Stator inductance | 2.97 mH |
| Maximum radial force Fr | 3730 N at 1000 rpm; 2960 N at 2000 rpm; 2580 N at 3000 rpm |
| Maximum axial force Fa | 740 N |
| Type of cooling | Natural convection |
| Length | 321 mm |
| Centring collar diameter | 180 mm |
| Centring collar depth | 4 mm |
| Number of mounting holes | 4 |
| Mounting holes diameter | 14 mm |
| Circle diameter of the mounting holes | 215 mm |
| Net weight | 35 kg |
| Sizing reference | SH32051P |
| Temperature copper hot | 130 °C |
| Number of motor stacks | 1 |
| Output current 3s peak | 87.2 A |
| Inertia | 0.0 kg.cm² of brake; 71.4 kg.cm² of motor |
| Contractual warranty |
| Warranty (in months) | 18 |
| Logistical informations |
| Country of origin | DE |
| Main |
| Range compatibility | PacDrive 3 |
| Device short name | SH3 |
| Product or component type | Servo motor |
| Packing Units |
| Unit Type of Package 1 | PCE |
| Number of Units in Package 1 | 1 |
| Package 1 Height | 40.000 cm |
| Package 1 Width | 80.000 cm |
| Package 1 Length | 30.000 cm |
| Package 1 Weight | 35.000 kg |
| Unit Type of Package 2 | PAL |
| Number of Units in Package 2 | 2 |
| Package 2 Height | 55.000 cm |
| Package 2 Width | 85.000 cm |
| Package 2 Length | 65.000 cm |
| Package 2 Weight | 80.000 kg |
Lexium SH3 servo motor. This SH3 series of AC servo motors has a low rotor moment of inertia, which enables high acceleration capability for dynamic applications. Thanks to the winding technology, a higher power density is achieved in a compact design. This servo has a nominal continuous stall torque of 36.9 Nm and achieves a peak torque of 110 Nm. Its nominal speed is up to 3600 rpm depending on the supply voltage. This results in a voltage-dependent nominal power of up to 5.2 kW. The built-in encoder is designed as a multiturn with 128 periods/revolution (128x1024x4096) as a SinCos Hiperface. The electrical connection is made via M40 + M23 connectors, angled by 90° and rotatable. The motor flange is 205 mm for fastening. The drive shaft has a diameter of 38 mm. The shaft end is designed with a feather key and corresponds to protection class IP54. The motor housing corresponds to protection class IP65. There is no holding brake. The servo amplifiers from the Lexium series Lexium 52 & Lexium 62 are recommended for operating the synchronous motor.