| Complementary |
| Maximum mechanical speed | 6000 rpm |
| [Us] rated supply voltage | 115...480 V |
| Network number of phases | Three phase |
| Continuous stall current | 4.8 A |
| Continuous stall torque | 5.8 N.m at 115...480 V three phase |
| Continuous power | 1900 W |
| Peak stall torque | 18.3 N.m at 115...480 V three phase |
| Nominal output power | 580 W at 115 V single phase; 1090 W at 230 V single phase; 1930 W at 400 V three phase; 2210 W at 480 V three phase |
| Nominal torque | 5.5 N.m at 115 V single phase; 5.2 N.m at 230 V single phase; 4.6 N.m at 400 V three phase; 4.4 N.m at 480 V three phase |
| Nominal speed | 1000 rpm at 115 V single phase; 2000 rpm at 230 V single phase; 4000 rpm at 400 V three phase; 4800 rpm at 480 V three phase |
| Maximum current Irms | 17.1 A |
| Shaft end | Smooth shaft |
| Shaft diameter | 19 mm |
| Shaft length | 40 mm |
| IP degree of protection | IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5; IP65 motor: conforming to IEC 60034-5; IP65 shaft bushing: conforming to IEC 60034-5 |
| Encoder type | Absolute single turn SinCos Hiperface |
| Speed feedback resolution | 128 periods |
| Holding brake | Without |
| Mounting support | International standard flange |
| Motor flange size | 100 mm |
| Electrical connection | Rotatable right angled connector |
| Torque constant | 1.21 N.m/A at 120 °C |
| Back emf constant | 77 V/krpm at 20 °C |
| Number of motor poles | 4.0 |
| Rotor inertia | 2.31 kg.cm² |
| Stator resistance | 2.4 Ohm |
| Stator inductance | 6.75 mH |
| Maximum radial force Fr | 990 N at 1000 rpm; 790 N at 2000 rpm; 690 N at 3000 rpm; 620 N at 4000 rpm |
| Maximum axial force Fa | 160 N |
| Type of cooling | Natural convection |
| Length | 204.5 mm |
| Centring collar diameter | 95 mm |
| Centring collar depth | 3.5 mm |
| Number of mounting holes | 4 |
| Mounting holes diameter | 9.0 mm |
| Circle diameter of the mounting holes | 115 mm |
| Net weight | 5.8 kg |
| Sizing reference | SH31002P |
| Temperature copper hot | 130 °C |
| Output current 3s peak | 17.1 A |
| Inertia | 0.0 kg.cm² of brake; 2.31 kg.cm² of motor |
| Contractual warranty |
| Warranty (in months) | 18 |
| Logistical informations |
| Country of origin | DE |
| Main |
| Range compatibility | PacDrive 3 |
| Device short name | SH3 |
| Product or component type | Servo motor |
| Packing Units |
| Unit Type of Package 1 | PCE |
| Number of Units in Package 1 | 1 |
| Package 1 Height | 21.0 cm |
| Package 1 Width | 18.0 cm |
| Package 1 Length | 35.6 cm |
| Package 1 Weight | 6.717 kg |
Lexium SH3 servo motor. This SH3 series of AC servo motors has a low rotor moment of inertia, which enables high acceleration capability for dynamic applications. Thanks to the winding technology, a higher power density is achieved in a compact design. This servo has a nominal continuous stall torque of 5.8 Nm and achieves a peak torque of 18.3 Nm. Its nominal speed is up to 4800 rpm depending on the supply voltage. This results in a voltage-dependent nominal power of up to 2210 W. The built-in encoder is designed as a single-turn with 128 periods/revolution (128x1024) as a SinCos Hiperface. The electrical connection is made via 2x M23 connectors, angled by 90° and rotatable. The motor flange is 100 mm for fastening. The drive shaft has a diameter of 19 mm. The shaft end is smooth and corresponds to protection class IP54. The motor housing has protection class IP65. There is no holding brake. The servo amplifiers from the Lexium series Lexium 52 & Lexium 62 are recommended for operating the synchronous motor.