| Complementary |
| Maximum mechanical speed | 8000 rpm |
| [Us] rated supply voltage | 115...480 V |
| Network number of phases | Three phase |
| Continuous stall current | 4.1 A |
| Continuous stall torque | 2.94 N.m at 115...480 V three phase |
| Continuous power | 1330 W |
| Peak stall torque | 11.3 N.m at 115...480 V three phase |
| Nominal output power | 460 W at 115 V single phase; 880 W at 230 V single phase; 1450 W at 400 V three phase; 1550 W at 480 V three phase |
| Nominal torque | 2.95 N.m at 115 V single phase; 2.8 N.m at 230 V single phase; 2.1 N.m at 400 V three phase; 2.1 N.m at 480 V three phase |
| Nominal speed | 1500 rpm at 115 V single phase; 3000 rpm at 230 V single phase; 6000 rpm at 400 V three phase; 7200 rpm at 480 V three phase |
| Maximum current Irms | 17.0 A |
| Shaft end | Parallel key |
| Shaft diameter | 14 mm |
| Shaft length | 30 mm |
| Key width | 5 mm |
| IP degree of protection | IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5; IP65 motor: conforming to IEC 60034-5; IP65 shaft bushing: conforming to IEC 60034-5 |
| Encoder type | Absolute single turn SinCos Hiperface |
| Speed feedback resolution | 128 periods |
| Holding brake | Without |
| Mounting support | International standard flange |
| Motor flange size | 70 mm |
| Electrical connection | Straight connector |
| Torque constant | 0.72 N.m/A at 120 °C |
| Back emf constant | 49 V/krpm at 20 °C |
| Number of motor poles | 3.0 |
| Rotor inertia | 0.58 kg.cm² |
| Stator resistance | 2.7 Ohm |
| Stator inductance | 7.3 mH |
| Maximum radial force Fr | 730 N at 1000 rpm; 580 N at 2000 rpm; 510 N at 3000 rpm; 460 N at 4000 rpm; 430 N at 5000 rpm; 400 N at 6000 rpm |
| Maximum axial force Fa | 80 N |
| Type of cooling | Natural convection |
| Length | 220 mm |
| Centring collar diameter | 60 mm |
| Centring collar depth | 2.5 mm |
| Number of mounting holes | 4 |
| Mounting holes diameter | 5.5 mm |
| Circle diameter of the mounting holes | 82 mm |
| Net weight | 3.6 kg |
| Sizing reference | SH30703P |
| Temperature copper hot | 130 °C |
| Output current 3s peak | 17.0 A |
| Inertia | 0.0 kg.cm² of brake; 0.58 kg.cm² of motor |
| Contractual warranty |
| Warranty (in months) | 18 |
| Logistical informations |
| Country of origin | DE |
| Main |
| Range compatibility | PacDrive 3 |
| Device short name | SH3 |
| Product or component type | Servo motor |
| Packing Units |
| Unit Type of Package 1 | PCE |
| Number of Units in Package 1 | 1 |
| Package 1 Height | 11.176 cm |
| Package 1 Width | 18.796 cm |
| Package 1 Length | 39.370 cm |
| Package 1 Weight | 4.014 kg |
Lexium SH3 servo motor. This SH3 series of AC servo motors has a low rotor moment of inertia, which enables high acceleration capability for dynamic applications. Thanks to the winding technology, a higher power density is achieved in a compact design. This servo has a nominal continuous stall torque of 3.1 Nm and achieves a peak torque of 11.3 Nm. Its nominal speed is up to 7200 rpm depending on the supply voltage. This results in a voltage-dependent nominal power of up to 1550 W. The built-in encoder is designed as a single-turn with 128 periods/revolution (128x1024) as a SinCos Hiperface. The electrical connection is made via 2x M23 connectors, angled by 90° and rotatable. The motor flange is 70 mm for fastening. The drive shaft has a diameter of 14 mm. The shaft end is designed with a feather key and corresponds to protection class IP54. The motor housing has protection class IP65. There is no holding brake. The servo amplifiers from the Lexium series Lexium 52 & Lexium 62 are recommended for operating the synchronous motor.