Complementary
[Us] rated supply voltage	24...240 V AC/DC 50/60 Hz, non self-powered
Supply voltage limits	20.4…264 V AC; 20.4…264 V DC
Supply frequency	50/60 Hz +/- 10 %
Power consumption in VA	0…4 VA at 24...240 V AC
Measurement range	208...480 V AC; 15...3100 Ohm
Measurement voltage limits	176…528 V AC
Time delay type	Without
Reset time	10000 ms output
Response time	> 50 ms (input Y1 (contact Y1-T1) and push-button)
Output contacts	2 NO
nominal output current	5 A
Maximum switching voltage	250 V AC
Switching capacity in VA	1250 VA
Minimum switching current	10 mA at 5 V DC
Maximum switching current	5 A AC; 5 A DC
Electrical durability	100000 cycles
Mechanical durability	30000000 cycles
Control circuit frequency	50...60 Hz +/- 10 %
Resistance across terminals	602 kOhm
Short-circuit current	0.007 A temperature sensing circuit (T1-T2 terminals short circuited)
Maximum resistance	1500 Ohm for temperature sensor at 20 °C
Tripping threshold	3100 Ohm +/- 10 % for temperature control circuit
Reset threshold	1650 Ohm +/- 10 % for temperature control circuit
Maximum power consumption in W	0.5 W DC
Contractual warranty
Warranty (in months)	18
Environment
Electromagnetic compatibility	Emission standard for industrial environments conforming to IEC 61000-6-4; Emission standard for residential, commercial and light-industrial environments conforming to IEC 61000-6-3; Immunity for industrial environments conforming to IEC 61000-6-2
Standards	IEC 60255-6; IEC 60034-11-2
Product certifications	CSA; C-Tick; GOST; UL; GL
Marking	CE
Directives	73/23/EEC - low voltage directive; 89/336/EEC - electromagnetic compatibility
Ambient air temperature for storage	-40…70 °C; -40…70 °C
Ambient air temperature for operation	-20…50 °C
Relative humidity	95 % at 55 °C conforming to IEC 60068-2-30
IP degree of protection	IP20 (terminals) conforming to IEC 60529; IP30 (casing) conforming to IEC 60529
Pollution degree	3 conforming to IEC 60664-1
Overvoltage category	III conforming to IEC 60664-1
Dielectric test voltage	2 kV, 1 min AC 50 Hz
Insulation resistance	> 500 MOhm at 500 V DC between supply and relay output conforming to IEC 60255-5
[Ui] rated insulation voltage	400 V conforming to IEC 60664-1
Operating position	Any position without derating
Connections - terminals	Screw terminals, 1 x 0.5...1 x 4 mm² (20 AWG...11 AWG) solid without cable end; Screw terminals, 2 x 0.5...2 x 2.5 mm² (20 AWG...14 AWG) solid without cable end; Screw terminals, 1 x 0.2...1 x 2.5 mm² (24 AWG...12 AWG) flexible with cable end; Screw terminals, 2 x 0.2...2 x 1.5 mm² (24 AWG...16 AWG) flexible with cable end
Tightening torque	0.6…1 N.m conforming to IEC 60947-1
Housing material	Polycarbonate
Local signalling	LED (green) for power ON; LED (yellow) for phase of relay (R2); LED (yellow) for temperature of relay (R1)
Mounting support	35 mm symmetrical DIN rail conforming to IEC 60715
Height	90 mm; 88.9 mm
Width	35 mm; 35.6 mm
Depth	72 mm; 71.1 mm
Net weight	0.095 kg; 0.10 kg
Logistical informations
Country of origin	ID
Main
Range of product	Harmony Control Relays
Relay type	Motor temperature control relay
Product or component type	Motor temperature control relay
Relay name	RM35TM
Relay monitored parameters	Phase failure detection; Phase sequence; Test/reset button; Motor temperature via PTC probe; Selection (with or without memory)
Control type	With test button
Contacts type and composition	2 NO
[Uc] control circuit voltage	24...240 V
Product specific application	For 3-phase supply
Packing Units
Unit Type of Package 1	PCE
Number of Units in Package 1	1
Package 1 Height	8.000 cm
Package 1 Width	4.500 cm
Package 1 Length	9.500 cm
Package 1 Weight	130.000 g
Unit Type of Package 2	S03
Number of Units in Package 2	48
Package 2 Height	30.000 cm
Package 2 Width	30.000 cm
Package 2 Length	40.000 cm
Package 2 Weight	6.969 kg

This monitoring relay is used in three-phase networks to monitor the phase sequence and phase failure and can monitor the temperature of motors with a built-in PTC sensor. A relay output with a normally open contact is available for phase monitoring and temperature monitoring. An error memory can be used as an option, which holds messages until a reset. The wide-voltage power supply enables universal use. The cable connection is made via screw terminals.