Complementary
Power quality analysis	up to the 63rd harmonic
Metering type	Measured neutral current; Calculated ground current
Device application	Gateway; WAGES metering; Power monitoring; Multi-tariff
Type of measurement	Current; Voltage; Frequency; Power factor; Energy; Active and reactive power
[Us] rated supply voltage	24 V DC
Network frequency	60 Hz; 50 Hz
[In] rated current	1 A; 5 A
type of network	3P + N; 3P; 1P + N
Maximum power consumption in VA	16 VA at 480 V
Ride-through time	35 ms 120 V AC typical; 129 ms 230 V AC typical; 50 ms 125 V DC typical
Display type	Monochrome graphic LCD
Display resolution	128 x 128 pixels
Sampling rate	128 samples/cycle
Measurement current	50…10000 mA
Analogue input type	Voltage (impedance 5 MOhm); Current (impedance
Measurement voltage	20…400 V AC 45...65 Hz between phase and neutral; 20…828 V AC 45...65 Hz between phases
Frequency measurement range	45…65 Hz
Number of inputs	4 digital
Measurement accuracy	Apparent power +/- 0.5 %; Frequency +/- 0.05 %; Active energy +/- 0.2 %; Reactive energy +/- 1 %; Active power +/- 0.2 %; Voltage +/- 0.1 %; Power factor +/- 0.005; Current +/- 0.15 %; Reactive power +/- 1 %
Accuracy class	Class 0.2S active energy conforming to IEC 62053-22
Number of outputs	2 digital
Information displayed	Tariff (8)
Communication port protocol	Modbus RTU and ASCII at 9.6, 19.2 and 38.4 kbauds even/odd or none - 2 wires, insulation 2500 V; JBUS; Modbus TCP/IP at 10/100 Mbit/s, insulation 2500 V; Ethernet Modbus TCP/IP daisy chain; BACnet IP; DNP3 over ethernet
Communication port support	RS485; ETHERNET
Communication gateway	Ethernet/serial
Data recording	Event logs; Maintenance logs; Min/max of instantaneous values; Data logs; Alarm logs; Time stamping
Memory capacity	1.1 MB
Web services	Alarm notification by e-mail; Web server; Diagnostic via predefined web pages; Real time viewing of data
Ethernet service	SNTP client; SNMP-Traps
Connections - terminals	Voltage circuit: screw terminal block4; Control circuit: screw terminal block2; Current transformer: screw terminal block6; RS485 link: screw terminal block4; Digital input: screw terminal block8; Digital output: screw terminal block4; Ethernet network: RJ45 connector2
Mounting mode	Flush-mounted
Mounting support	Framework
Standards	EN 50470-3; IEC 61557-12:2015; IEC 62053-22:2020; IEC 62053-24; IEC 60529; EN 50470-1; UL 61010-1; IEC 62053-23:2020; IEC 62052-11:2020; IEC 62052-31:2015
Product certifications	CE conforming to IEC 61010-1; CULus conforming to UL 61010-1
Width	96 mm
Depth	72 mm
Height	96 mm
Net weight	450 g
Contractual warranty
Warranty (in months)	18
Environment
IP degree of protection	IP54 display: conforming to IEC 60529; IP30 rear: conforming to IEC 60529
Relative humidity	5…95 % at 50 °C non-condensing
Pollution degree	2
Ambient air temperature for operation	-25…70 °C
Ambient air temperature for storage	-40…85 °C
Logistical informations
Country of origin	IN
Main
Range	PowerLogic
Product name	PowerLogic PM5000
Product or component type	Power meter
Device short name	PM5580
Packing Units
Unit Type of Package 1	PCE
Number of Units in Package 1	1
Package 1 Height	11.500 cm
Package 1 Width	12.500 cm
Package 1 Length	13.000 cm
Package 1 Weight	575.000 g
Unit Type of Package 2	S03
Number of Units in Package 2	12
Package 2 Height	30.000 cm
Package 2 Width	30.000 cm
Package 2 Length	40.000 cm
Package 2 Weight	7.440 kg

The PowerLogic PM5580 is a universal meter for front mounting (96 mm x 96 mm) with a fully graphic and backlit LCD display. The meter offers an accuracy of class 0.2s according to the IEC 62053-22 standard and 128 samples per cycle. The meter measures energy, active and reactive power, voltage, current, frequency, power factor and up to the 63rd harmonic. With 4 quadrant energy measurement. 1.1 MegaBytes memory for up to 14 selectable parameters with configurable interval and duration. This meter also has direct neutral monitoring. The device operates in a DC network and accepts a supply voltage of 24 VDC. The rated current of this meter is 1 A or 5 A and supports configurations with one phase and neutral, three phases or three phases and neutral. The measuring voltage range between phases is 20 to 690 VAC at 45 to 65 Hz. The measuring range between phase and neutral is 20 to 400 VAC at 45 to 65 Hz. Communication protocols are Modbus RTU and ASCII 2 wires with RS485 interface as well as Modbus TCP/IP, Ethernet/IP and BACnet/IP based on 10/100 Mbit/s, Daisy Chain Ethernet with RJ45 connection support. The integrated communication functions enable support of the DNP 3.0 protocol, access to an integrated web server and a serial to Ethernet gateway. The meter also has 4 digital inputs with pulse support and 2 digital outputs. There are 52 configurable alarms and 8 tariffs are supported. The product dimensions are as follows: width 96 millimeters, depth 77 millimeters, height 96 millimeters and product weight 450 g.